SOLOPLAN-FA TM_GB_1116.pdf
4 Các trang
200 KB
Download
<h1>SOLOPLAN-FA TM_GB_1116.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>SOLOPLAN®-FA</p> <p>Art.-No. 2 00012</p> <p>ry</p> <p>ve</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />14 <br />2 00012</p> <p>io n</p> <p>Self levelling, fibre reinforced floor levelling compound</p> <p>l o w e m iss</p> <p>EN 13818 <br />SOLOPLAN-FA <br />Cement screeding mortar for <br />use in buildings <br />CT-C30-F7 <br />Reaction to fire <br /> Class E <br />Release of corrosive <br />substances CT <br />Compressive strength <br />C30 <br />Flexural strength <br />F7</p> <p>• Fibre reinforced and low shrinkage <br />• Very low emissions <br />• Suitable for heated screeds <br />• For interiors <br />• For thicknesses from 3 to 20 mm <br />• Rapid hardening <br />• Highly polymer modified <br />• Self levelling <br />• Class RWFC-550, according to EN 13892-7 <br />after 16 h <br />Areas of application: <br />SOLOPLAN-FA is a powder based, highly modified <br />factory blended mortar with reinforcing fibres, which <br />minimises cracks on wooden floors. SOLOPLAN-FA <br />is used at thicknesses from 3 – 20 mm for smoothing, <br />floating and levelling. The wooden floor levelling <br />compound SOLOPLAN-FA is suitable for producing flat, <br />absorbent installation surfaces e.g. for textile finishes, <br />vinyl or cushion flooring, PVC designer flooring, linoleum, <br />cork and tiles. <br />• On timber floor boards, V100 chipboard without <br />additional reinforcing mesh <br />• On old substrates with bonded adhesive and levelling <br />compound residues <br />• For the restoration and repair of wooden floors and <br />additionally for screeds and substrates in old and new <br />construction</p> <p>• For producing flat, absorbent, high strength installation <br />surfaces for textile and elastic floor finishes as well as <br />for ceramic tiles. When using beneath tiles and natural <br />or agglomerate stone, plan for additional de-coupling <br />membranes on wooden substrates. STEPBOARD in 9 <br />and 15 mm thicknesses are available for this purpose. <br />• Suitable for use on heated substrates and as a flowing <br />material over thin build-up electrical and warm water <br />heating systems. <br />SOLOPLAN-FA is used in dry areas and can also be <br />incorporated into rooms with low moisture exposure (wet <br />duty exposure class A0 in accordance with the ZDB data <br />sheet [*1]) when used beneath a waterproof membrane <br />from AQUAFIN-2K/M, AQUAFIN-2K or <br />AQUAFIN-RS300. Not suitable as a wearing finish <br />without additional planned coatings. <br />Technical Data: <br />Basis: <br />special cement with mineral- <br /> <br />based aggregates and <br /> additives <br />Colour: grey <br />Application temp: <br />min. +10°C floor, ideally <br /> <br />+15°C to +25°C at relative <br /> <br />humidity < 75% <br />Pot life *1): <br />approx. 45 mins <br />Foot traffic after *1): <br />approx. 3 hrs <br />Full service conditions <br />after *1): <br />approx. 24 hrs <br />Drying time *1) *2): <br />approx. 1 day / 3 mm layer <br /> <br />for elastic and textile flooring as <br /> <br />well as natural stone, approx. 1 <br /> <br />day / 10 mm thickness for <br /> <br />ceramic finishes <br />Classification: <br />EN 13813 CT-C30-F7 <br />Reaction to fire: <br />class E <br />Cleaning: <br />with water whilst fresh</p> <p>1/4</p> <p>11/16</p> <p>Consumption: <br />approx. 1.6 kg/m²/mm <br /> thickness <br />Thickness</p> <p>Consumption</p> <p>Sufficient for <br />approx.</p> <p>3 mm</p> <p>4.8 kg/m²</p> <p>5.2 m²</p> <p>6 mm</p> <p>9.6 kg/m²</p> <p>2.6 m²</p> <p>9 mm</p> <p>14.4 kg/m²</p> <p>1.7 m²</p> <p> <br />Storage: <br />dry, 6 months in the original <br /> <br />unopened packaging. Use <br /> <br />opened packaging promptly. <br />Packaging: <br />25 kg plastic bag <br />*1) These values relate to +20ºC and 65% relative humidity for <br />a 3 mm thickness. Higher temperatures accelerate and lower <br />temperatures retard the setting time. <br />*2) This information relates to guide values, which does not negate the <br />need for moisture measurements by the carbide method.</p> <p>Substrate preparation: <br />The substrate must be load-bearing conforming to loading <br />requirements of DIN 1055 and in accordance with <br />DIN 18365 and DIN 18352, must be sound, dry, free <br />from cracks, clean and free from substances acting as a <br />separating layer. Thoroughly mechanically remove friable <br />layers, separating and laitance layers and similar by <br />suitable measures e.g. planing, blast cleaning techniques <br />or scabbling. Vaccum abrasion dust, then prime with <br />ASO-Unigrund-S. Block off wall/floor junctions e.g. with <br />the edge insulating strip RD-SK50. Moisture from the <br />substrate must be eliminated. <br />Clean and abrade well bonded ceramic tiles, prime with <br />ASODUR-SG2 blinded with 0.5 – 1.0 mm quartz sand. <br />Remove excess by vacuum once cured. <br />Wooden substrates must be clean, dry and load-bearing. <br />Replace damaged floor boards. Secure loose, springy or <br />squeaking boards or sheets with screws. Chipboard must <br />be laid with staggered joints, screwed and glued. <br />The residual moisture of wooden substrates (measured <br />by kiln drying or with a moisture meter suitable for wood) <br />may not exceed 6 to 12% by weight from equilibrium</p> <p>moisture content. Seal joints, cracks and holes with an <br />acrylic sealant. <br />Follow the product information for the application of <br />products to be used. <br />The readiness of substrates to receive SOLOPLAN-FA is to <br />be tested by the carbide method. The carbide hygrometer <br />(CM device) may not exceed for: <br />Cement-based screeds 2.0 CM% <br />Calcium sufate screeds with underfloor heating 0.5 CM% <br />Calcium sufate screeds with underfloor heating 0.3 CM% <br />The CM measurements are to be carried out in <br />accordance with current FBH-AD work instructions from <br />the technical information “Coordination of cut-out points <br />with heated floor constructions”. <br />Product preparation: <br />1. <br />Prime substrates with ASO-Unigrund-S and allow to <br />dry. On calcium sulfate and cement-based screeds, <br />use diluted 1:1 with water. Use two undiluted coats <br />of ASO-Unigrund-S on timber substrates. <br />2. <br />Place 6.0 – 6.3 litres of clean water into a clean <br />bucket and sprinkle in 25 kg SOLPLAN-FA. Mix the <br />contents until homogenous with a drill or rotating mixer <br />(max. 600 rpm). We recommend the use of a drill <br />with 500 – 600 rpm using a Collomix paddle type <br />RR140 to 160. <br />3. Pour SOLOPLAN-FA on to the primed substrate and <br />evenly spread with a smoothing trowel or rake within <br />the pot life, so that the required thickness is applied in <br />one operation where possible. De-aerate the liquid <br />layer with a spiked roller and encourage to flow. The <br />surface and flow are decidedly improved. <br />4. <br />Protect setting material from rapid water loss from e.g. <br />high room temperatures, direct sunlight and draughts. <br />The air, material and substrate temperatures may not <br />drop below +5ºC during application and for the <br />week after. <br />5. <br />The surface quality and absorption is increased by <br />abrading with 40 to 60 grit after 12 – 24 hours.</p> <p>2/4</p> <p>11/16</p> <p>Priming table <br />Calcium sufate screed</p> <p>ASO-Unigrund-S <br />(Mixing ratio 1:1 with water)</p> <p>Cement-based screed</p> <p>ASO-Unigrund-S <br />(Mixing ratio 1:1 with water)</p> <p>Wooden substrates <br />(screwed) such as e.g. <br />OSB boards, wooden floor <br />boards, V100 chipboard</p> <p>ASO-Unigrund-S</p> <p>Well bonded ceramic tiles, <br />terrazzo</p> <p>ASODUR-SG2 *</p> <p>*Blinded to excess with 0.5 – 1.0 mm quartz sand. Only sweep <br />off and vacuum excess sand once reacted (approx. 16 hrs *1).</p> <p>Important advice: <br />• Before installing finishes, the levelling compound <br />must be fully dry. We recommend that moisture <br />measurements are carried out with a carbide <br />hygrometer. <br />• Adequate ventilation beneath the wooden floor must <br />be guaranteed especially when installing further <br />vapour proof finishes e.g. by installing ventilation <br />slots or by inserting special skirting strips with vented <br />openings. <br />• The subfloor construction of wooden floors must be <br />permanently dry in order to prevent moisture damage <br />from decay or mould formation. <br />• There is a risk of cracking through rapid water loss in <br />heated rooms or highly absorbent substrates. <br />• Ventilation on site is necessary. However avoid <br />draughts during the application and curing process <br />as well as direct sunlight. The floor and interior <br />temperature must be at least +5ºC during application <br />and for the week after. Dehumidifiers may only be <br />used after the first 3 days. <br />• Essential to the success of floor levelling is the <br />condition of the substrate. Absorbent substrates <br />negatively alter the flow performance of the <br />compound. Therefore thoroughly prepare the <br />substrate, clean and prime. <br />• Completely remove sulphite lye adhesives.</p> <p>• As far as possible, mechanically remove small <br />quantities of dispersion-based flooring adhesives, <br />clean and prime with ASODUR-GBM or ASODURSG2 blinding to excess with 0.5 – 1.0 mm quartz <br />sand. Remove excess by vacuum once cured. <br />• Watch the water addition. Adding too much water <br />produces separation together with a weak surface. <br />This causes increased cracking and hollow areas. <br />Such weak surfaces are to be mechanically removed. <br />• Perimeter, bay, structural and intermediate movement <br />joints are to be brought through or incorporated as <br />designed and blocked off with a suitable material e.g. <br />edge insulation strip (RD-SK50). <br />• Substrates with a coarse texture lead to greater <br />material consumption. <br />• High temperatures accelerate and low temperatures <br />retard the setting process. <br />• Observe the relevant current regulations. E.g. <br />DIN 18157 <br />DIN 18365 <br />DIN 18352 <br />DIN 18560 <br />DIN EN 13813 <br />DIN 1055 <br />The BEB information sheets, distributed by the <br />Bundesverband Estrich und Belag e.V. <br />The technical information “coordination of cut out <br />points in heated floor constructions”. <br />The ZDB information sheets, distributed by the <br />professional association of the German tile industry: <br />[*1] “Bonded waterproof membranes” <br />[*2] “Tiling to calcium sulfate screeds <br />[*3] “Movement joints in wall and floor tile finishes” <br />[*5] “Ceramic tiles, natural stone and cement-bound <br />composite slabs on cement-based floor constructions <br />with insulation” <br />[*6] “Ceramic tiles, natural stone and cement-bound <br />composite slabs on heated cement-based floor <br />constructions” <br />[*9] “Tolerances in level” <br />[*10] “Tolerances”</p> <p>3/4</p> <p>11/16</p> <p>• Use only clean tools and clean water. <br />• Follow the information in the technical data sheets for <br />the products used. <br />Please observe a current valid EU Health & <br />Safety Data Sheet! <br />GISCODE: ZP1</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the <br />product. Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>4/4</p> <p>WKD/CoS/JD</p> <p>11/16</p>
