SOLOFLEX-FAST TM GB_4915.pdf
4 Các trang
200 KB
Download
<h1>SOLOFLEX-FAST TM GB_4915.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>SOLOFLEX-FAST </p> <p>Reaction to fire: <br />Bond strength, as <br />tensile adhesion strength after <br />dry storage: <br />Durability, as <br />tensile adhesion strength after <br />water immersion: <br />tensile adhesion strength after <br />warm storage: <br />tensile adhesion strength after <br />freeze/thaw cycles: <br />Early tensile adhesion strength <br />after 6 hrs: </p> <p>ry</p> <p>ve</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />11 <br />2 05439 <br />EN 12004 <br />SOLOFLEX-FAST <br />Fast setting, cement-based adhesive <br />with increased performance for the <br />installation of tiles in interior and <br />exterior areas <br />C2 F</p> <p>io n</p> <p>Art.-No. 2 05439 <br />Thin and medium bed adhesive, flexible and rapid hardening</p> <p>l o w e m iss</p> <p>Class A1/A1fl <br />≥ 1 N/mm²</p> <p>≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 1 N/mm² <br />≥ 0.5 N/mm²</p> <p>Properties: <br />•C <br /> onforms to DIN EN 12004, <br />C2 FT <br />• Rapid hardening <br />• Long pot life <br />• Slump resistant <br />•W <br /> ith rapid crystalline water <br />binding <br />• For interior and exterior use <br />• Polymer modified <br />• Smooth application <br />• Resistant to water and freeze / thaw cycles <br />• Up to 15 mm bed thickness <br />Areas of application: <br />As a rapid hardening, slump resistant thin and medium <br />bed adhesive, SOLOFLEX-FAST is the preferred choice <br />for work under time constraints for the installation <br />of vitrified and earthenware tiles, ceramic tiles with <br />low water absorption ≤ 0.5% (fully vitrified), clinker, <br />mosaics, cementitious tiles, cement-based slabs and <br />natural stone that is not translucent nor sensitive to <br />discolouration. <br />Despite its rapid setting nature, SOLOFLEX with FAST <br />technology possesses a long pot life and open time. <br />Also when working and substrate temperatures are</p> <p>low, the water is bound in a crystalline form so that <br />a noticeably quicker strength development can be <br />detected in comparison with conventional rapid setting <br />adhesives. SOLOFLEX-FAST is suitable for the secure <br />fixing of tiles to flat, sound substrates and for tiling onto <br />mineral based and dispersion based SCHOMBURG <br />waterproof membranes, in moderate wet duty areas. <br />On horizontal external areas such as e.g. balconies and <br />terraces, modify 25 kg of SOLOFLEX-FAST with 8.33 kg <br />of UNIFLEX-B. <br />Technical Data: <br />Basis: <br />Cement, aggregate and <br /> additives <br />Colour: Grey <br />Bulk density: <br />approx. 1.24 kg/dm3 <br />Pot life *): <br />approx. 45 to 60 mins <br />Open time *): <br />approx. 20 mins <br />Foot traffic *): <br />After approx. 3 hrs <br />Grout after *): <br />approx. 3 hrs <br />Fully serviceable *): <br />After approx. 7 days <br />Consumption: <br />approx. 2.5 kg/m2 with a <br /> <br />6 mm notched trowel <br /> approx. 3.3 kg/m2 with an <br /> <br />8 mm notched trowel <br /> approx. 4.2 kg/m2 with a <br /> <br />10 mm notched trowel <br /> approx. 6.0 kg/m2 with <br /> <br />a 12/20 mm half moon – <br /> medium bed trowel <br /> approx. 6.0 kg/m2 with a <br /> <br />10 mm Flowline notched <br /> trowel <br />Packaging: <br />25 kg bags <br />Cleaning: <br />Clean tools immediately with <br /> water after use <br />Storage: <br />Dry, 6 months in the original <br /> <br />unopened packaging. Use <br /> opened packaging promptly. <br />Application/substrate <br />temperature: <br />+5° C to +25° C <br />* These values relate to +20° C and 65% relative humidity</p> <p>1/4</p> <p>49/15</p> <p>Substrate preparation: <br />SOLOFLEX-FAST is suitable for the secure installation of <br />tiles to dimensionally stable substrates conforming to <br />DIN 18 157 part 1 e.g. concrete, aerated concrete, <br />render / plaster, cement-based and calcium sulfate <br />based screeds, masonry work etc. The substrate must <br />be dry, sound, adequately flat, free from penetrating <br />cracks and free from separating substances such as <br />e.g. oil, paint, laitance and loose areas. It must have <br />a surface condition and strength consistent with its <br />type. When installing tiles, substrate preparation must <br />be carried out to DIN 18 157 part 1. Prime porous <br />substrates with ASO-Unigrund. Calcium sulfate based <br />screeds must be abraded, vacuumed and as with all <br />calcium sulfate based substrates, thoroughly primed <br />with ASO-Unigrund-GE. If large format tiles are to be <br />installed, we recommend that priming is carried out <br />using ASODUR-V360W due its greater barrier forming <br />capacity. Heated screeds must be commissioned in line <br />with recognized technical regulations before tiling. To <br />ascertain a surface’s readiness to receive tiles, carry out <br />moisture measurements with a carbide hygrometer (CM <br />device). The CM moisture content may not exceed: <br />•C <br /> ement-based screeds ≤ 2.0% for floating or <br />unbonded screeds <br />•C <br /> alcium sulfate screeds without underfloor <br />heating ≤ 0.5% <br />•C <br /> alcium sulfate screeds with underfloor <br />heating ≤ 0.3% <br />The CM measurement is to be carried out in <br />accordance with the current work instructions from the <br />technical information of the FBH-AD “Coordination of <br />cut out areas with heated floor constructions”. <br />Product preparation: <br />Mix SOLOFLEX-FAST with clean water in a clean mixing <br />bucket until homogenous. <br />Mixing ratio: <br />1.8 – 2.0 litres water : 6 kg SOLOFLEX-FAST <br />7.5 – 8.5 litres water : 25 kg SOLOFLEX-FAST <br />On horizontal external surfaces such as e.g. balconies <br />and terraces, SOLOFLEX-FAST is to be modified with <br />UNIFLEX-B. Furthermore we recommend the addition</p> <p>of UNIFLEX-B to SOLOFLEX-FAST when installing large <br />format tiles greater than 60 x 60 cm. Modification with <br />the UNIFLEX-B elastifier improves the deformability and <br />tensile adhesion strength of SOLOFLEX-FAST. Dependent <br />on the modification, class S2 can be achieved, which <br />is especially recommended for large format tiles greater <br />than 60 x 60 cm. This considerably compensates <br />against shear stresses which can lead to de-bonding <br />under unfavourable external conditions. To improve the <br />workability, add water once the SOLOFLEX-FAST has <br />been mixed with UNIFLEX-B. The addition of UNIFLEX-B <br />will shorten the open time. The deformability to DIN EN <br />12004 is considerably increased so that class S2 <br />is achieved. <br />Mixing ratio: <br />2 kg UNIFLEX-B : 6 kg SOLOFLEX-FAST : <br />approx. 0.5 litres water <br />8.33 kg UNIFLEX-B : 25 kg SOLOFLEX-FAST : <br />approx 2.0 litres water <br />After standing for 3 minutes, mix through once again. <br />Do not mix more SOLOFLEX-FAST than can be used <br />within the pot life. <br />Spread SOLOFLEX-FAST adhesive onto the surface of <br />the substrate and comb through with the appropriately <br />sized notched trowel for the tile format. Install the <br />finishing material within the open time. Always clean <br />mixing containers as setting SOLOFLEX-FAST functions <br />as an accelerator. Do not mix with other cement-based <br />mortars. <br />Important advice: <br />• Not suitable for underwater areas. <br />• When installing natural or agglomerate stone always <br />observe their specific product properties (tendency to <br />discolour, risk of curling etc.) and the stone producer’s <br />installation recommendations. We recommend that a <br />test area is carried out. <br />• To safely avoid curling effects caused by water <br />absorption when installing serpentinite, slate and <br />with agglomerate / synthetic stone which contain <br />these natural stones, we recommend the use of <br />ASODUR-EK98 or ASODUR-Design.</p> <p>2/4</p> <p>49/15</p> <p>•W <br /> hen installing agglomerate / synthetic stone we <br />recommend that 25 kg SOLOFLEX-FAST is modified <br />with 2.0 kg UNIFLEX-B. <br />•W <br /> hen installing tiles or slabs to poured asphalt of <br />hardness class IC10 we recommend that 25 kg <br />SOLOFLEX-FAST is modified with 2.0 kg UNIFLEX-B. <br />• P erimeter, bay, structural joints and movement joints <br />are to be brought through or incorporated in the <br />designed position and blocked with an appropriate <br />medium e.g. edging strip RD-SK50. Saw cut joints <br />are to be adhesively sealed or secured against <br />uneven levels. <br />• T horoughly prime calcium sulfate based substrates <br />such as ASO-NM15 with ASO-Unigrund-GE, <br />ASO-Unigrund-S, ASO-Unigrund-K (mixing ratio 1:3 <br />with water) or ASODUR-V360W. ASODUR-V360W <br />has the greatest blocking effect of the substrate. To <br />avoid the formation of ettringite with calcium sulfate <br />based substrates, UNIFIX-AEK is suitable for tiling <br />to these substrates up to residual moisture levels, <br />measured with a carbide hygrometer, of 1.0% when <br />heated and 1.5% when unheated. <br />•W <br /> hen installing large format tiles greater than 50 x <br />50 cm, apply a scratch coat to the rear of the tile to <br />improve adhesion, or fix using the floating-buttering <br />method. <br />•D <br /> o not re-life adhesives that has already started to <br />harden, by adding more water or fresh adhesive as <br />there is a risk of inadequate strength development. <br />•W <br /> hen installing tiles in heavy duty external areas <br />(balconies/terraces) we recommend the installation <br />of the highly elastic waterproof membrane system <br />AQUAFIN-RS300, AQUAFIN-2K/M or AQUAFIN-2K. <br />• In permanently wet areas (swimming pools, containers <br />etc.) we recommend the use of the system thin bed <br />adhesives UNIFIX-2K, UNIFIX-S3, UNIFIX-2K/6 onto <br />the SCHOMBURG waterproof membrane suitable <br />for the area of application. Observe the specific <br />properties of the finishing products to be installed. <br />• P rotect areas where SOLOFLEX-FAST is not being <br />used, from its effects. <br />• Instead of ASO-Unigrund-GE, ASO-Unigrund-K diluted <br />1:3 with water can also be used. <br />•S <br /> OLOFLEX-FAST is a hydraulic setting mortar that is <br />to be protected from water and frost penetration until</p> <p>fully cured, which in adverse weather conditions can <br />take a few days. <br />• Direct contact between cement-based adhesives and <br />magnesium screeds leads to destruction via chemical <br />reaction. Therefore rising moisture from the substrate <br />must be eliminated through appropriate measures. <br />Mechanically roughen the magnesite surface and <br />prime with the epoxy resin ASODUR-V360W with <br />the addition of max. 5% water as necessary <br />(approx. 250 g/m2). Wait for approx. 12 – 24 <br />hours at +20° C then apply a second coat of <br />ASODUR-V360W (approx. 300 – 350 g/m2). <br />Blind the second coat whilst it is still wet with an <br />excess of 0.5 – 1.0 mm quartz. Wait for a further <br />12 – 16 hours before further work. <br />• Follow the relevant current regulations. For e.g. <br />DIN 18157, DIN 18352, DIN 18560, EN 13813, <br />DIN 18202, DIN 1055 <br />The BEB technical sheets issued by the federal <br />association for screeds and finishes Technical sheet <br />from the experts EURO-F-E-N Schloss Raesfled “Tiles, <br />slabs, natural and concrete slabs on poured asphalt <br />in interior areas” <br />The professional information “Coordination of cut out <br />points with heated floor constructions” <br />The technical construction information on natural stone <br />from the Natural Stone Association <br />The ZDB technical sheets issued by the Professional <br />Association of the German tile industry: <br />[*2] “Finishes on calcium sulfate screeds” <br />(October 2005) <br />[*3] “Movement joints in tile and slab finishes” <br />[*4] “Heavy duty ceramic tiled finishes” <br />[*5] “Ceramic tiles and slabs, natural and concrete <br />slabs on cement-based floor constructions on <br />insulation” <br />[*6] “Ceramic tiles and slabs, natural and concrete <br />slabs on heated cement-based floor constructions” <br />[*7] “Exterior tiling” <br />[*8] “Finishes on poured asphalt” <br />[*9] “Height variations” <br />[*10] “Tolerances” <br />[*11] “Cleaning, protection, maintenance”</p> <p>3/4</p> <p>49/15</p> <p>Please observe a valid EU health & safety data sheet. <br />Low-chromate. <br />GISCODE: ZP1</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. <br />Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>4/4</p> <p>WKD/CoS/JD</p> <p>49/15</p>
