TM INDUFLOOR-IB1275_GB_1216.pdf
3 Các trang
90 KB
Download
<h1>TM INDUFLOOR-IB1275_GB_1216.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>INDUFLOOR®-IB1275 </p> <p> </p> <p>Priming and levelling mortar</p> <p>Properties: <br />INDUFLOOR-IB1275 is a <br />two component, solvent free <br />epoxy resin primer: <br />• pre-filled <br />• very good ability to <br />de-aerate <br />• good substrate wetting <br />capacity <br />• self levelling when used <br />as a levelling mortar <br />• thicknesses from 0 - 2 mm</p> <p>Art.-No. 2 03510</p> <p>Packaging: <br />28.5 kg container <br /> <br />Component A and B are <br /> <br />supplied at a pre-determined <br /> mix ratio <br />Storage: <br />12 months when stored dry <br /> <br />and cool above +10° C <br /> <br />in the original unopened <br /> packaging.</p> <p>1119</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2– 8 <br />D-32760 Detmold <br />13 <br />5 50063 <br />EN 1504-2 <br />INDUFLOOR-IB1275 <br />Surface protection product - Impregnation <br />Principle 1.2 <br />Capillary water absorption and <br />water permeability <br />w < 0.1 kg/m² × h <br />Penetration depth <br />Class I < 10 mm <br />Tensile adhesion strength <br />by pull-off test <br />≥ 1.5 (1.0) N/mm² <br />Reaction to fire <br />Class E <br />Hazardous substances In compliance with <br /> <br />5.3 EN 1504-2</p> <p>0.5</p> <p>Areas of application: <br />As a primer or levelling mortar <br />on cement-based areas such as concrete and screed <br />beneath the following INDUFLOOR coatings: <br />• INDUFLOOR-IB-3357 <br />• INDUFLOOR-IB-3358</p> <p>Technical Data: <br />Basis: <br />2 component epoxy resin <br />Viscosity: <br />approx. 2000 – 2500 mPa·s <br /> at +20° C <br />Density: <br />approx. 1.50 g/cm3 <br /> <br />at + 23° C <br />Mixing ratio: <br />100 : 14 parts by weight <br />Pot life: <br />approx. 60 mins at +10° C <br /> <br />approx. 45 mins at +23° C <br /> <br />approx. 25 mins at +30° C <br />Application temperature: min. +10° C, <br /> max. +30° C <br />Substrate temperature: > 8° C and 3° K above <br /> dew point <br />Foot traffic after: <br />min. 12 hrs at +23° C <br />Overcoat after: <br />approx. 12 hrs, max. 24 hrs <br /> at +23° C <br />Tensile adhesion <br />strength: <br />Concrete failure (B1.5) <br />Flexural strength: <br />53.5 N/mm2 <br />Compressive strength: 71.5 N/mm2 <br />Cleaning: <br />Clean work tools thoroughly <br /> after use with <br /> INDU-IB-Cleanser</p> <p>Substrate preparation: <br />The areas to be treated must be: <br />• firm, sound and have a good grip <br />• free from separating and adhesion inhibiting <br />substances such as dust, laitance, grease, <br />rubber marks, paint residues and similar. <br />• protected from moisture penetration from the rear. <br />Use suitable means to prepare the substrate dependent <br />on its condition such as e.g. sweeping, vacuuming, <br />brushing, planing, scabbling, grit-blasting, shot-blasting. <br />The following criteria are to be observed dependent <br />on the particular substrate: <br />• Concrete quality: <br />• Screed quality: <br />Tensile adhesion <br />strength: <br />• Poured asphalt: </p> <p>min. C 20/25 <br />min. EN 13813 CT-C25-F4 <br />>1.5 N/mm² <br />min. AS-IC 15</p> <p>Product preparation: <br />Components A (resin) and B (hardener) are delivered <br />at a predetermined mixing ratio. Tip component B <br />into component A. Ensure that the hardener drains <br />completely from its container. Mixing of the components <br />is to be carried out with a suitable mixer at approx. <br />300 rpm (e.g. drill with paddle). It is important to <br />also stir from the sides and the bottom to ensure that <br />the hardener is evenly dispersed. Stir until the mix is <br />homogenous (free from streaks); mixing time 2 minutes. <br />The minimum temperature during mixing should be <br />+15° C. Do not use mixed material directly from <br />the packaging. Decant the material into a clean <br />container and mix through thoroughly once again.</p> <p>1/3</p> <p>12/16</p> <p>Application method/consumption: <br />Use as a primer: <br />Pour the mixed INDUFLOOR-IB1275 in portions over <br />the area, spread with a rubber squeegee and then <br />back roll with a short nap roller. Avoid ponding and <br />bubble formation. Do not broadcast sand into the <br />primer once completed. Apply subsequent coatings <br />after a maximum waiting time of 24 hours at +23 °C. <br />Consumption: 300 - 500 g/m² dependent on the <br />absorption of the substrate. <br />Use as a levelling compound for irregularities <br />of 1.00 - 2.00 mm: <br />Evenly apply a single coat of INDUFLOOR-IB1275 <br />with a notched trowel or toothed rake to the desired <br />thickness and, where there are air bubbles, slowly <br />and evenly roll through with a spiked roller (metal type <br />- Polyplan spiked roller or similar). Do not broadcast <br />sand into the primer once completed. <br />Apply subsequent coatings after a maximum waiting <br />time of 24 hours at +23 °C.</p> <p>•</p> <p>Consumption for dry substrates: <br />Depth of <br />irregularity</p> <p>0.5 – 1.00 mm</p> <p>1.00 – 2.00 mm</p> <p>Consumption</p> <p>0.60 – 1.50 kg/m2</p> <p>1.50 – 3.00 kg/m2</p> <p>Consumption for matt damp substrates: <br />Depth of <br />irregularity</p> <p>0.5 – 1.00 mm</p> <p>1.00 – 1.50 mm</p> <p>Consumption</p> <p>0.60 – 1.50 kg/m2</p> <p>1.50 – 2.20 kg/m2</p> <p>Health & Safety: <br />INDUFLOOR-IB1275 is harmless once cured. The <br />hardener (B) component is corrosive. When using <br />the product follow the government health & safety <br />regulations (data sheet M023) as well as the advice <br />on the containers. <br />Important advice: <br />• As a rule SCHOMBURG products are supplied in <br />working packs i.e. at a predetermined mixing ratio.</p> <p>• <br />•</p> <p>•</p> <p>•</p> <p>2/3</p> <p>With deliveries in large containers, part quantities will <br />need to be weighed using scales. Always thoroughly <br />stir the filled components and only then blend with <br />the second component. This is to be carried out with <br />a suitable rotary mixer e.g. Polyplan/Ronden mixing <br />paddle or similar. In order to exclude mixing errors, <br />decant into a clean container and remix. The mixing <br />speed should be 300 – 400 rpm. Ensure that no <br />air is entrained. Higher speeds drag unnecessary air <br />quantities into the product whilst lower speeds do not <br />result in a good blend or require too long a mix time <br />(pot life). The temperature of the components should <br />be at a minimum of +15° C. This is also applicable <br />to any fillers, e.g. sand, to be mixed in. The addition <br />of any fillers is carried out after both liquids have <br />been blended. Afterwards tip the completely mixed <br />material immediately onto the prepared substrate and <br />promptly thoroughly spread in accordance with the <br />instructions in the technical data sheet. Always stir <br />one component products before using. <br />The application on to substrates covered in dew must <br />always be avoided. Furthermore, damp sand may <br />not be used and ensure that sweat does not fall on <br />to the fresh coating, as this leads to foaming of the <br />material. <br />The bond between the individual coats can be <br />heavily impeded through the influence of moisture or <br />contamination between successive applcations. <br />If there is a long time period between coatings or if <br />already treated surfaces are to be re-coated after a <br />long time period, then thoroughly clean and abrade <br />the surface followed by a the application of a <br />completely new pore free coat. It is not sufficient to <br />simply overcoat. <br />Surface protective systems must be protected for <br />approx. 4 – 6 hours from dampness after application <br />(e.g. rain, melt water). Dampness produces a white <br />discolouration and/or stickiness on the surface and <br />can impede the cure. Discoloured and/or sticky <br />surfaces should be taken off e.g. by abrading and <br />renewed. <br />Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />Technical Services Department of SCHOMBURG.</p> <p>12/16</p> <p>•C <br /> ured product residues can be disposed of under <br />waste disposal classification 15010. <br />• Please observe a valid EU safety data sheet! <br />Paint products directive (2004/42/EG): <br />Group Lb: j <br />Level 2 (2010): max. 500 g/l <br />INDUFLOOR-IB1275 contains: < 500 g/l <br />GISCODE: RE 1</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. <br />Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>3/3</p> <p>Höl/CoS/JD 12/16</p>
