TM INDUBOND-Tape-3000_GB_0616.pdf
2 Các trang
50 KB
Download
<h1>TM INDUBOND-Tape-3000_GB_0616.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>INDUBOND-Tape-3000 </p> <p> </p> <p>Thermoplastic joint tape for waterproofing joints</p> <p>Properties: <br />• Highly flexible <br />• Simple, homogenous weld <br />• No activation necessary <br />• Impermeable to water even <br />against negative pressure <br />• Can be applied to matt damp <br />substrates without priming <br />• Resistant to frost, UV and <br />ageing</p> <p>DD-4442/ÜBB/2012</p> <p>KIWA MPA <br />Bautest GmbH, <br />NL Dresden</p> <p>Areas of application: <br />INDUBOND-Tape-3000 is used in combination <br />with INDUBOND-VK4031 for waterproofing day/ <br />construction joints and expansion joints as well as <br />for waterproofing cracks and voids in concrete <br />construction. It is additionally suitable for waterproofing <br />transitions, penetrations or differing building materials. <br />Substrate preparation: <br />The substrate must be clean and load-bearing as <br />well as free from adhesion inhibiting materials. <br />At the time of installation it may be matt damp but <br />not wet or with saturated pores. In the area to be <br />waterproofed, mechanically prepare the substrate using <br />suitable means e.g. planing, scabbling or grit blasting <br />etc., in order to ensure a good bond. When using <br />on substrates other than concrete, assess with a trial <br />adhesion test. <br />When applying joint waterproofing as strips it is <br />essential that the concrete has waterproof qualities. <br />Otherwise the joint waterproofing must be used <br />in combination with a surface applied waterproof <br />membrane. <br />Product application: <br />Coat the prepared substrate on both sides of the joint <br />to be bridged with INDUBOND-VK4031 to a width <br />min. 1 cm wider than the INDUBOND-Tape-3000 <br />being used. Then lay the joint tape and thoroughly <br />bed into the adhesive layer with a trowel or pressure <br />roller without voids or folds and coat over the top. In so</p> <p>Art.-No. 5 55114</p> <p>doing, ensure that the joint tape is completely bedded. <br />The adhesive or smoothing coat thickness should never <br />be less than 1 mm. Overlap butt joints by a min. of <br />5 to 10 cm and bond or alternatively hot air weld. <br />Expansion joints: <br />Expansion joints always require a 2 mm joint tape and <br />can either be laid flush or in a loop dependent on the <br />project. To accomodate expansion, leave an unbonded <br />section of tape in the expansion area. Dependent <br />on the installation and loading e.g. overhead use or <br />negative water pressure, a reinforcing or supporting <br />construction may be necessary. <br />Hot air welding: <br />The joint tapes are cut to suit the project (butt joints or <br />corner joints) and laid on a flat substrate. Butt joints <br />are to be overlapped by a min. 5 cm. The overlap <br />area is to be roughened with abrasive paper and <br />cleaned. Welding is carried out with hot air equipment <br />with a wide nozzle and a pressure roller. The welding <br />temperature (reference values: approx. 300 - 350 °C) <br />is to be set by a trial weld. The joints in the tapes are <br />laid on top of one another appropriately and fixed <br />at the edges by selective welding in order to prevent <br />slipping during welding. Then the wide nozzle of <br />the hot air tool is drawn slowly and evenly over the <br />overlap area and fully joined together with a pressure <br />roller. Before installing check the weld for a complete <br />watertight bond. <br />Technical Data: <br />Basis: TPE <br /> (Thermoplastic Elastomer) <br />Colour: grey <br />Shore A hardness <br />to ISO 868: <br />approx. 87 <br />Temperature resistance: -30°C / +90°C <br />Application, substrate <br />and material <br />temperature: <br />+ 5°C to + 35°C</p> <p>1/2</p> <p>06/16</p> <p>Material thickness</p> <p>1.0 mm</p> <p>2.0 mm</p> <p>Weight per unit <br />area, g/m²</p> <p>approx. 900</p> <p>approx. 1800</p> <p>Tensile strength <br />at break, to DIN <br />EN ISO 527-3, <br />N/mm²</p> <p>approx. 14.0</p> <p>approx. 14.0</p> <p>Elongation at <br />break, to DIN EN <br />ISO 527-3, %</p> <p>approx. 1000</p> <p>approx. 1000</p> <p>Tear propogation <br />strength, to DIN <br />12310-2, N:</p> <p>approx. 100</p> <p>approx. 200</p> <p>Consumption INDUBOND-VK4031: <br />Consumption in kg/m <br />Size/ <br />Thickness</p> <p>1.0 mm</p> <p>2.0 mm</p> <p>150 mm</p> <p>approx. 0.8</p> <p>approx. 1.4</p> <p>200 mm</p> <p>approx. 1.0</p> <p>approx. 1.5</p> <p>250 mm</p> <p>approx. 1.1</p> <p>approx. 1.7</p> <p>300 mm</p> <p>approx. 1.3</p> <p>approx. 1.8</p> <p>500 mm</p> <p>approx. 1.8</p> <p>approx. 2.4</p> <p>Sizes: <br />150, 200, 250, <br /> <br />300, 500 1000 mm <br />Storage: <br />dry and protected <br /> from weathering, 12 <br /> <br />months in the original <br /> unopened packaging. <br /> <br />Use within 2 months <br /> once opened. <br />Advice: <br />• Unlike Hypalon tapes, INDUBOND-Tape-3000 does <br />not require additional surface activation. It must not <br />be brought into contact with solvents. <br />• INDUBOND-Tape-3000 provides excellent adhesion <br />to the epoxy adhesive INDUBOND-VK4031. <br />• Protect the joint tape from mechanical damage by <br />suitable protective measures. <br />• With negative water pressure > 0.5 bar a suitable <br />supporting system (apron plate) is indispensible.</p> <p>Does not consider extra material consumption for <br />uneven substrates.</p> <p> </p> <p>Combined test with INDUBOND-VK4031: <br />Tensile adhesion strength, <br />to PG- ÜBB: <br />> 3.0 N/mm² with <br /> break in concrete <br />Water impermeability, <br />positive and negative <br />according to DIN 1048: <br />5 bar <br />Crack bridging to PG-ÜBB, <br />1.0 mm crack held for 28 d <br />Water pressure 0.75 bar: <br />passed <br />Reaction to fire: <br />Class E to <br /> DIN EN 13501-1 <br />Packaging: <br />20 m rolls <br />This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the product. <br />Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>SF/CoS/JD</p> <p>06/16</p>
