ASODUR-EMB_TM_GB_2915.pdf
2 Các trang
80 KB
Download
<h1>ASODUR-EMB_TM_GB_2915.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax <br />+ 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Technical Data Sheet</p> <p>ASODUR®-EMB</p> <p>Art.-No. 2 05790</p> <p>Epoxy resin mortar</p> <p>• Two component. <br />• Solvent free. <br />• For interior or exterior use. <br />SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />06 <br />2 05790 <br />EN 13813 <br />ASODUR-EMB <br />Resin-based screed / resin-based coating <br />for interior rooms <br />SR-B1,5-AR1-IR4 <br />Reaction to fire according to K 2010/85/EU E <br />Release of corrosive substances <br />SR <br />Resistance to wear <br />AR1 <br />Tensile strength <br />≥ B1,5 <br />Impact resistance <br />IR4</p> <p>Areas of application: <br />ASODUR-EMB is used for repairing cementitious surfaces <br />as well as for the construction of coved fillets on e.g. <br />concrete roads, ramps and industrial floors. <br />Technical Data: <br />Base: <br />2 component epoxy resin <br />Colour: grey <br />Viscosity: <br />mortar consistency <br />Density: <br />approx. 2.0 g/cm3 <br />Mix ratio: <br />100 : 3.6 parts by weight <br />Curing temperature: <br />(material/substrate): +10 °C to +30 °C <br />Pot life: <br />approx. 40 mins at +23 °C <br />Ready for use: <br />after approx. 16 hours up to <br /> <br />max. 24 hours at +23 °C <br />Overcoat: <br />after approx. 16 hours up to <br /> <br />max. 24 hours at +23 °C <br />Compressive strength: approx. 100 N/mm2 <br />Flexural strength: <br />approx. 35 N/mm2 <br />E-modulus: <br />approx. 16000 N/mm2 <br />Cleaning of tools: <br />Thoroughly clean tools <br />immediately after use with <br />AQUAFIN-Cleanser. <br />Packaging: <br />8 kg container <br />Components A and B are <br /> <br />supplied in the correct mixing <br /> <br />ratios.</p> <p>Storage: <br /> <br /> <br /> </p> <p>Cool and dry 18 months in <br />original unopened packaging <br />above +10° C. Storage must <br />be in accordance with the <br />regulations for the storage of <br />material hazardous to water <br />courses.</p> <p>Surface preparation: <br />The area to be treated must be: <br />• dry, firm, sound and have a good grip <br />• free from separating and adhesion inhibiting <br />substances such as dust, laitance, grease, oil, rubber <br />marks, paint residues and similar. <br />• protected from moisture ingress from the rear. <br />Depending on type and size of application, use as <br />appropriate any of the following surface preparation <br />methods: grit blasting, scabbling, shot blasting or <br />grinding. As a guideline all surfaces should be rated <br />as follows: <br />Cementitious substrates: <br />• Concrete quality: min. C20/25 <br />• Screed quality: <br />min. CT-C25-F4 <br />• Age: <br />min. 28 days <br />• Tensile adhesion <br />strength: <br />>1,5 N/mm2 <br />• Residual moisture: < 4 % <br /> <br />(carbide hygrometer method) <br />Product preparation: <br />Component A (mortar) and component B (hardener: <br />inside) are delivered in a complimentary mix ratio. <br />Tip component B into component A. Ensure that the <br />hardener drains completely from the container. Mixing <br />of the components is to be carried out with a suitable <br />mixer at approx. 300 rpm (e.g. drill with paddle). It is <br />important to stir from the sides and the bottom to ensure <br />that the hardener is evenly dispersed. Stir until the mix is <br />homogenous. Mix time approx. 5 minutes. The material <br />temperature should be approx. +15° C during the mix <br />process. Do not use the mixed material directly from the</p> <p>1/2</p> <p>29/15</p> <p>delivered packaging! Decant the mass into a clean mix <br />bucket and thoroughly mix through once again. Use a <br />forced paddle mixer (e.g. Colormatic, Zyklos or Uez) <br />for larger projects. <br />Method of application / consumption: <br />1. Surface preparation – see above <br />2. Prime the area to be treated: <br />Apply ASODUR-GBM in one coat with a roller. <br />Consumption: approx. 300–500 g/m2 <br />2.1 Repair of damaged or defective areas in concrete <br />and screeds: <br />ASODUR-EMB is inserted into the primed damaged <br />or defective area, compacted and struck-off level with <br />the surface. <br />Consumption: approx. 2000 g/m2/mm thickness <br />3. Production of coved fillets: <br />Form the coved fillet with ASODUR-EMB with a <br />trowel over the primed area. <br />Radius: approx. 3–5 cm <br />Consumption: approx. 1800 g/m (with a coved fillet <br />radius of approx. 5 cm)</p> <p>Important advice: <br />• Higher temperatures shorten the pot life. Lower <br />temperatures lengthen the pot life and curing time. <br />Material consumption is also increased at lower <br />temperatures. <br />• Applications that are not clearly explained in this <br />technical data sheet may only be carried out after <br />consultation with and written confirmation from the <br />technical services department of SCHOMBURG. <br />• Waste code: liquid product residues: EAK O8 01 <br />11 pigment and lacquer waste that contains organic <br />solvents or other harmful materials. Cured product <br />residues: EAK 17 02 03 plastic. <br />Please observe a valid EU safety data sheet. <br />GISCODE: RE1</p> <p>This technical data sheet is a translation from German and does not consider local building codes or legal requirements. It shall be used as general reference for the <br />product. Legally binding is only the latest German technical data sheet or the latest data sheet from one of our foreign subsidiaries inside their sales territory.</p> <p>2/2</p> <p>CJ/CoS/JD</p> <p>29/15</p>
