SOLOCRET-50_Product_information_GB_2616.pdf
2 页数
189.1 KB
Download
<h1>SOLOCRET-50_Product_information_GB_2616.pdf</h1> <p>Product information <br />Smoothing and levelling compounds</p> <p>SOLOCRET®-50 <br />Anti-sag smoothing compound – rapid hardening</p> <p>Technical Data: <br />Basis: </p> <p>Special cement, aggregate, high quality additives</p> <p>Flexural and compressive <br />strength*: </p> <p>4.0 N/mm²/25 N/mm² after 28 days</p> <p>Application temperature: </p> <p>+5 °C to +25 °C</p> <p>Pot life*: </p> <p>min. 30 mins</p> <p>Water addition: 4.0–4.5 l water : 25 kg SOLOCRET®-50 <br /> <br />(dependent on thickness installed) <br />Consumption: </p> <p>approx. 1.5 kg/m²/mm thickness</p> <p>Overcoat*: </p> <p>after approx. 3–4 hrs</p> <p>Foot traffic*: </p> <p>after approx. 7 day</p> <p>Packaging: </p> <p>25 kg plastic bag</p> <p>TS/CoS/JD</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>26/16</p> <p>Areas of application: <br />• SOLOCRET®-50 is a rapid hardening, highly slump resistant <br />smoothing compound for use at thicknesses from 2-50 mm in <br />one application for preparing substrates before the <br />subsequent installation of ceramic tiles and slabs, natural <br />and artificial stone as well as other finishes, including over <br />underfloor heating. <br />• SOLOCRET®-50 can be used on suitable substrates such as <br />e.g. mineral-based substrates; concrete to DIN 1045, <br />heated and unheated cement-based screeds to DIN <br />18560, cement-based renders, old well adhered tiled <br />finishes and rapid setting cement-based screeds. <br />• SOLOCRET®-50 is suitable for exterior and wet duty areas <br />when an appropriate SCHOMBURG bonded waterproof <br />membrane is installed.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>*) Values are valid at +23° C and 50% relative humidity.</p> <p>2 05440</p> <p>1 Load-bearing substrate</p> <p>2 Cleaning the wall substrate</p> <p>3 Priming the substrate, e.g. with <br />ASO-®Unigrund</p> <p>4 Adding the smoothing compound to the <br />pre-weighed water</p> <p>5 Mixing the smoothing compound</p> <p>6 Levelling uneven areas in walls</p> <p>7 Cleaning the floor substrate</p> <p>8 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>9 Levelling and/or creating falls in the floor</p> <p>10 Even walls and floor ready to receive <br />finishes</p> <p>SOLOCRET®-50 <br />Anti-sag smoothing compound <br />– rapid hardening</p> <p>Properties: <br />• For thicknesses from 2 - 50 mm in <br />one application <br />• Rapid hardening <br />• Low shrinkage <br />• Smooth and easy application <br />• For interior and exterior use <br />• Suitable for heated screeds <br />• For walls, ceilings and floors</p> <p>Product application: <br />Prime the substrate with ASO-Unigrund. Cement-based substrates can also <br />be pre-wetted until matt damp. <br />Mix SOLOCRET®-50 at a ratio of approx. 4.0 to 4.5 l water : 25 kg <br />SOLOCRET®-50 with clean water in a clean mixing bucket with a suitable <br />drill mixer for approx. 3-5 minutes until homogenous. After standing for <br />approx. 5 mins, stir through once again. Do not mix more material than can <br />be used within 30 minutes. Produce a scratch coat and then trowel out <br />SOLOCRET®-50 and spread evenly with a suitable tool (plasterer’s darby) <br />within the working life of the product. <br />SOLOCRET®-50 can be applied to surfaces at a thickness of 50 mm in <br />one application and for localised defects also to a thickness of 100 mm. <br />After approx. 60–80 minutes (dependent on the substrate, ambient <br />conditions and thickness), SOLOCRET®-50 can be smoothed off or <br />roughened with a grid float to remove uneven areas and produce a rough <br />surface texture, which provides a good key for subsequent applications of <br />bonded materials.</p> <p>Application: <br />The substrate must be dry, load-bearing, adequately flat, free from <br />penetrating cracks and free from separating substances such as e.g. oil, <br />paints, laitance layers and loose components. It must have a largely closed <br />texture and possess surface characteristics and strength typical for its type. <br />Prime absorbent substrates with ASO®-Unigrund. Heat substrates with <br />underfloor heating before applying finishes. The readiness of a substrate to <br />receive finishes is to be determined using the carbide (CM) method and <br />may not fall below the following values: <br />•CT ≤ 2.0 % <br />•CA/ CFA unheated ≤ 0.5 %, heated ≤ 0.3 %</p>
