SANIFLEX_Product_information_GB_2616.pdf
2 页数
282.9 KB
Download
<h1>SANIFLEX_Product_information_GB_2616.pdf</h1> <p>Product information <br />Waterproofing systems</p> <p>SANIFLEX <br />Liquid waterproof membrane for <br />bonded waterproofing systems</p> <p>Technical Data: <br />Basis: solvent free polymer dispersion with carbonate fillers <br />Colour: </p> <p>ochre and grey</p> <p>Ready for foot traffic/ <br />ready to receive finishes*: after approx. 1 day <br />Pot life*: </p> <p>approx. 60 mins</p> <p>Wet duty exposure class: A (wall), A0 <br />Substrate/Material/ <br />Application temperatur: </p> <p>+5°C to + 30°C</p> <p>Consumption: <br /> <br /> </p> <p>approx. 1.2 kg/ m² per approx. 0.5 mm dry film thickness <br />(no allowance has been made for greater consumption due <br />to uneven substrates)</p> <p>Packaging: <br /> <br /> <br /> </p> <p>5, 12 and 20 kg packs in the colour ochre as a <br />trowel, brush or roller applied variant <br />20 kg pack in the colour grey as a trowel, brush <br />or roller applied variant</p> <p>* +20 °C and 65 % relative humidity</p> <p>ASO-Joint-Tape-2000</p> <p>×</p> <p>ASO-Joint-Tape-2000-S</p> <p>×</p> <p>ASO-Joint-Tape-2000-Corners, (90°, internal/external)</p> <p>×</p> <p>ASO-Joint-Tape-2000-S-Corners, (90°, internal/external)</p> <p>×</p> <p>ASO-Joint-Tape-2000-T-pieces, cross pieces</p> <p>×</p> <p>ASO-Joint-Sleeve-Floor/Wall</p> <p>×</p> <p>UNIFIX-S3</p> <p>×</p> <p>UNIFIX-2K</p> <p>×</p> <p>UNIFIX-2K/6</p> <p>×</p> <p>LIGHTFLEX</p> <p>×</p> <p>MONOFLEX-FB</p> <p>×</p> <p>MONOFLEX-XL</p> <p>×</p> <p>ASODUR-EK98-Wall/-Floor</p> <p>×</p> <p>ASODUR-Design</p> <p>×</p> <p>SOLOFLEX</p> <p>×</p> <p>AK7P</p> <p>×</p> <p>CRISTALLIT-flex</p> <p>×</p> <p>SOLOFLEX-white modified with UNIFLEX-B</p> <p>×</p> <p>CRISTALLIT-MULTI-flex</p> <p>×</p> <p>UNIFIX-S3-FAST</p> <p>×</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>×</p> <p>TS/CoS/JD</p> <p>Areas of application: <br />• SANIFLEX is used for seamless and jointless waterproofing <br />beneath tiles in wet duty areas where impermeability to water <br />is required such as e.g. in domestic bathrooms and kitchens, <br />private and commercial washrooms. <br />• SANIFLEX is suitable for walls in wet duty class A in <br />accordance with general technical test criteria and wet duty <br />class A0 in accordance with the ZDB data sheet “Bonded <br />waterproof membranes”. <br />• SANIFLEX is suitable for use in interior rooms in accordance <br />with the AgBB evaluation scheme (Committee for Healthrelated Evaluation of Building Products) and the French <br />VOC by-law. Very low emissions in accordance with <br />GEV-EMICODE, which as a rule leads to positive evaluation <br />within the scope of building certification systems in accordance <br />with DGNB, LEED, BREEAM, HQE.</p> <p>Exposure classes A, A0</p> <p>26/16</p> <p>System components <br />ASO-DB-Standard</p> <p>2 05004</p> <p>SANIFLEX <br />Liquids waterproof membrane <br />for bonded waterproofing <br />systems <br />Properties: <br />• One component <br />• Ready-to-use <br />• Fast drying <br />• Brush, roller or trowel applied <br />• Very easy to trowel and smooth <br />• Simple effective application <br />• Very low emissions <br />• Environmentally friendly as <br />solvent free <br />• Vapour permeable <br />• Elastic and impermeable to <br />water</p> <p>Product application: <br />1. Prime the substrate with ASO®-Unigrund. <br />2. Once the primer has dried, apply SANIFLEX undiluted with a steel float, <br />brush or a lamb’s wool roller. When trowel applying, an even thickness <br />is achieved by using a 4 mm notched trowel and subsequently <br />smoothening. At least two coats are required when brush or roller <br />applying. The previous coat must have dried out before the second coat <br />is applied. <br />3. For the formation of impermeable movement and connecting joints, insert <br />the system components from the ASO-Joint-Tape technology appropriate <br />for the particular wet duty class. Coat both sides of the joint to be <br />bridged with SANIFLEX with a 4–6 mm notched trowel. Lay the joint tape <br />into the wet coat and then carefully press into the waterproofing layer <br />with a steel trowel or hard roller, without voids or folds. Overlap joint <br />tape ends by a minimum of 5 to 10 cm, bond with SANIFLEX without <br />folds and with a full bed. <br />4. Installation of tiles is carried out with one of the named adhesives from <br />the system components. At the time of tiling, the waterproof coat must <br />have hardened. <br />5. Do not expose SANIFLEX to water until cured. In this context, bonded <br />overlapped areas of joint tape/pre-formed pieces will take considerably <br />longer to dry dependent on ambient conditions. <br />Application: <br />All flat, load-bearing surfaces, which can take tiles and bonded waterproof <br />membranes are suitable. Furthermore the suitability of the substrate in the <br />appropriate wet duty class must be given (refer to ZDB data sheet). <br />The substrate must be load-bearing, adequately flat to DIN 18202, free <br />from penetrating cracks and be free from separating substances such as <br />e.g. oil, paint, laitance layers and loose areas. <br />Plasters/renders to DIN EN 998-1 must have a minimum compressive <br />strength of 2.5 N/mm2 and be suitable for installing tiles in the relevant wet <br />duty class. <br />Ensure that there are no height differences within the substrate to receive <br />finishes and that there is no route for moisture penetration from the reverse <br />side.</p> <p>1 Load-bearing substrate</p> <p>2 Cleaning the wall substrate</p> <p>3 Priming the substrate, e.g. with <br />ASODUR®-GBM</p> <p>4 SANIFLEX, suitable tools</p> <p>5 Bonding the ASO®-Joint-Tape into the first <br />coat of the waterproofing membrane</p> <p>6 Application of the first coat of <br />waterproofing membrane</p> <p>7 Allow the first coat to dry</p> <p>8 Application of the second coat of <br />waterproofing membrane</p> <p>SCHOMBURG <br />GmbH & Co. KG <br />Detmold</p> <p>P-2002-4-1023/03 <br />KIWA MPA <br />Bautest GmbH, <br />NL Dresden</p> <p>v er</p> <p>y lo</p> <p>io n</p> <p> </p> <p>w e m is</p> <p>s</p> <p>9 Completed waterproof membrane <br />Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p>
