CRISTALLFUGE-HF_Produktinformation_0122.pdf
2 页数
323.7 KB
Download
<h1>CRISTALLFUGE-HF_Produktinformation_0122.pdf</h1> <p>joint mortar</p> <p>Flexible joint mortar <br />CRISTALLFUGE-HF</p> <p>Application <br />1. Mix CRISTALLFUGE-HF with clean water in a clean mixing bucket. <br />Add 4.1-4.5 l water depending on the desired consistency, add 25 kg <br />CRISTALLFUGE-HF, and then stir into a homogeneous, smooth <br />compound. We recommend mixing with a suitable stirrer. After an <br />activation time of 3 minutes, the joint mortar is stirred again. In order to <br />avoid colour differences, the mix ratio must always be kept the same. <br />2. CRISTALLFUGE-HF is added to the wall and floor areas with a suitable <br />jointing board and pulled diagonally to the joint cleanly, so that the joint <br />cross-section is filled completely. Do not scatter dry joint mortar powder. <br />3. After applying the joint mortar, wash the surface first with a moist sponge <br />board approx. 15–20* minutes (control via finger test). After approx. <br />10-15 minutes, wash off again with the sponge board.</p> <p>High-strength flex joint mortar <br />3-20 mm, CG2 W A</p> <p>Please refer to the currently valid technical data sheet for additional <br />instructions.</p> <p>Properties <br />• Rapid setting <br />• Very good binding and wash-off properties <br />• 3 - 20 mm joint width, curing without cracks <br />• For porcelain stoneware and many other coverings <br />• Increased abrasion resistance <br />• Resistant to high-pressure cleaning <br />• Fungus-resistant <br />• For interior and exterior use and under water <br />• Water-repellent <br />• Frost/thaw-resistant <br />• Suitable for floor and wall heating systems <br />• Colours matched to the ESCOSIL-2000 and <br />ESCOSIL-2000-ST silicone system</p> <p>Application <br />• After the bedding mortar sets, scratch out the joints sufficiently deep. <br />• Next, clean the tiled finish sufficiently damp. <br />• The bedding mortar must be fully set, since otherwise discolourations in <br />the grout finish could result. <br />• Pre-moisten strongly absorbing coverings with water equally. <br />• Joint edges must be clean and free of separating substances. <br />• The time of grouting of the tiles set in the thin-bed depends on the thinbed mortar and amounts to approx. 3 to 72 hours. <br />• In case of thick-bed laying, the mortar bed must be sufficiently firm and <br />equally dry. <br />• Do not grout on surfaces with different surfaces temperatures (e.g. due to <br />sun exposure). <br />• The consistency of joint mortar must be specified depending on <br />the absorbency of the covering and substrate to be grouted.</p> <p>Areas of use <br />• CRISTALLFUGE-HF is suitable for grouting porcelain <br />stoneware, vitrified tiles and stoneware boards, brick <br />tiles, artificial stone, facing bricks, veneer and floor <br />bricks in baths, showers, and living areas, on terraces, <br />balconies and loggias, and façades, as well as <br />heating flow screeds for joint widths from 3–20 mm. <br />• CRISTALLFUGE-HF is especially suited to grouting tiled <br />finishes in swimming pools, car washes, commercial <br />kitchens, sales showrooms, commercial and industrial <br />facilities, and workshops due to its high mechanical <br />durability. <br />• CRISTALLFUGE-HF may be used in areas where high <br />mechanical stress occurs, e.g. due to cleaning <br />equipment, high-pressure steam cleaners, or <br />mechanical floor cleaning machines. With increased <br />resistance to cleaning chemicals. Neutral and alkaline <br />cleaners with correct dosage can be used without <br />limitation.</p> <p>Tiles/boards <br />format (in cm)</p> <p>20.0 × 20.0</p> <p>Joint width <br />(in mm)</p> <p>4.0</p> <p>Joint depth <br />(in mm)</p> <p>8.0</p> <p>1A <br /> vailable floor surface, bonding bed is set</p> <p>2 CRISTALLFUGE-HF, suitable tools</p> <p>3 Fill the joint mortar into a clean mixing bucket</p> <p>4 Mix the joint mortar</p> <p>5 Apply the joint mortar</p> <p>6 Slide diagonally across excess joint mortar</p> <p>7 Emulsify the joint mortar after setting</p> <p>8 Rinsing off surfaces diagonally to the joint <br />direction</p> <p>9 Finished and jointed floor surface</p> <p>Note: The adjacent floor jointing process <br />is also valid for wall areas</p> <p>approx. <br />consumption <br />each 1 m2 (in kg)</p> <p>0.74</p> <p>30.0 × 30.0</p> <p>5.0</p> <p>8.0</p> <p>0.61</p> <p>30.0 × 30.0</p> <p>5.0</p> <p>15.0</p> <p>1.15</p> <p>40.0 × 40.0</p> <p>5.0</p> <p>10.0</p> <p>0.58</p> <p>30.0 × 5.0</p> <p>8.0</p> <p>10.0</p> <p>3.80</p> <p>24.0 × 11.5</p> <p>10.0</p> <p>12.0</p> <p>3.40</p> <p>24.0 × 11.5</p> <p>10.0</p> <p>20.0</p> <p>5.60</p> <p>Flexible high-performance mortar <br />CRISTALLFUGE-HF <br />High-strength flex joint mortar 3-20 mm, CG2 W A</p> <p>Technical data <br />Basis</p> <p>Cement, high-quality additives, special aggregates</p> <p>Colours</p> <p>cement grey, medium grey</p> <p>Classification</p> <p>EN 13888 CG2 W A</p> <p>Application temperature</p> <p>+5 °C to +25 °C</p> <p>Pot life*</p> <p>approx. 30–45 minutes</p> <p>Water addition</p> <p>4.1–4.5 l water: 25 kg CRISTALLFUGE-HF</p> <p>Consumption</p> <p>see consumption table</p> <p>Foot traffic* <br />Withstands loads*</p> <p> fter approx. 6 hours <br />a <br />after at least 7 days</p> <p>Packaging</p> <p>25 kg foil sack</p> <p>Colours** <br />cement grey</p> <p>medium grey <br />** Colour deviations are due to printing technology.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>01/22 TS/JD/Tet/LiW Subject to change. The valid issue of the corresponding technical bulletin legally applies.</p> <p>* at +23 °C and 50 % rel. humidity</p>
