ASO-Unigrund-GE_Product_Information_GB_4915.pdf
2 页数
209.7 KB
Download
<h1>ASO-Unigrund-GE_Product_Information_GB_4915.pdf</h1> <p>Product information <br />Primers</p> <p>ASO®-Unigrund-GE <br />Ready to use primer</p> <p>Technical Data: <br />Basis: </p> <p>acrylate dispersion</p> <p>Colour: green</p> <p>Consumption: </p> <p>approx. 200 g/m2</p> <p>Packaging: </p> <p>1, 5, 10, 25, 210 litre containers</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>TS/CoS/JD</p> <p>+5°C to +30 °C</p> <p>49/15</p> <p>Areas of application: <br />• ASO®-Unigrund-GE reduces the absorption of substrates, binds <br />surface dust, consolidates, prevents rapid water loss from <br />levelling compounds. <br />• ASO®-Unigrund-GE is used for priming absorbent and lightly <br />sanded substrates e.g. gypsum-based construction materials <br />(plaster, interlocking gypsum slabs, boards, screeds), concrete, <br />masonry work and similar. <br />• Suitable as an adhesion promoter for surface applied <br />waterproof membranes (e.g. SANIFLEX, AQUAFIN®-2K/M), <br />thin-bed adhesives as well as wall and floor levelling <br />compounds such as SOLOCRET®-50, SOLOPLAN®-30 and <br />ASO®-NM15. It is also suitable for exterior use.</p> <p>Application/substrate <br />temperature: </p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>Mixing ratio: ready to use</p> <p>2 05535</p> <p>Product preparation: <br />ASO®-Unigrund- GE is ready to use. Application is with a paint brush, <br />brush or a fine-pored sponge roller but it can also be sprayed with <br />suitable equipment. Avoid applying too thickly or forming puddles. <br />ASO®-Unigrund- GE must be fully dry before further work can be carried <br />out on the primed surface.</p> <p>ASO®-Unigrund-GE</p> <p>Application: <br />The substrate must be load-bearing, clean, dry and free from materials, <br />which will impede adhesion. Flow screeds must be abraded and <br />vacuumed. Remove unstable or weakly bonded layers e.g. release agents, <br />residues of old adhesive, levelling layers, surface finishes and paints, by <br />mechanical scrubbing, planing, scabbling or shot-blasting.</p> <p>1 Cleaning the wall substrate</p> <p>2 Priming the wall substrate</p> <p>3 Cleaning the floor substrate</p> <p>4 Priming the floor substrate</p> <p>Ready to use primer</p> <p>v er</p> <p>y lo</p> <p>io n</p> <p>Properties: <br />• Rapid drying <br />• Universal application <br />• Resistant to water and alkalis <br />• Low emission <br />• Solvent free <br />• For interior and exterior use</p> <p>w e m is</p> <p>s</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p>
