AQUAFIN-RS300_Product_information_GB_4815.pdf
2 页数
306.4 KB
Download
<h1>AQUAFIN-RS300_Product_information_GB_4815.pdf</h1> <p>Product information <br />Waterproofing systems</p> <p>AQUAFIN®-RS300 <br />Rapid setting hybrid waterproof <br />membrane</p> <p>Technical Data: <br />Basis: <br /> </p> <p>Preblended mortar, <br />cement/sand, polymer improved</p> <p> <br /> </p> <p>Liquid component Powder component <br />polymer dispersion special cement, <br />functional fillers</p> <p>Mixing ratio: </p> <p>1 part by weight </p> <p>Packaging: <br /> </p> <p>20 kg combined product <br />10 kg bucket <br />2 x 5 kg bag</p> <p> <br /> </p> <p>10 kg combined product <br />5 kg bucket <br />5 kg bag</p> <p>Colour: </p> <p>white grey</p> <p>1 part by weight</p> <p>Ready for foot traffic/ <br />ready to receive finishes*: after approx. 3 hrs (per coat) <br />Pot life: </p> <p>approx. 45 minutes</p> <p>Wet duty classification: </p> <p>A, B, A0, B0</p> <p>Substrate/Material/ <br />Application temperature: +5 to +30 °C <br />Consumption: </p> <p>approx. 15 kg per m²/ mm thickness</p> <p>TS/CoS/JD</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>48/15</p> <p>Areas of application: <br />• Waterproofing combined with tiled finishes: <br />For the effective and assured waterproofing in combination <br />with tiled finishes when longer term or frequent impermeability <br />to water is required e.g. in private bathrooms and kitchens, <br />private and public sanitary areas as well as balconies and <br />terraces, swimming pools and pool surrounds. <br />• AQUAFIN-RS300 is suitable for wet duty exposure classes <br />A and B in accordance with the technical test criteria for <br />regulated areas and wet duty exposure classes A0 and B0 <br />in accordance with the ZDB data sheet “Bonded waterproof <br />membranes“.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>* at +23 °C and 50 % relative humidity</p> <p>2 04208</p> <p>1 Load-bearing substrate</p> <p>2 Cleaning the substrate</p> <p>3 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>4 Filling out the waterproofing membrane at <br />the pre-determined mix ratio</p> <p>5 Mixing the waterproofing membrane</p> <p>6 Bonding the ASO®-Joint-Tape into the first <br />coat of the waterproofing membrane</p> <p>7 Application of the first coat of <br />waterproofing membrane</p> <p>8 Allow the first coat to dry</p> <p>9 Application of the second coat of <br />waterproofing membrane</p> <p>10 Finished waterproofing membrane ready <br />to receive finishes</p> <p>AQUAFIN®-RS300 <br />Rapid setting hybrid <br />waterproof membrane <br />Properties: <br />•2 <br /> component <br />• Multi-functional <br />•H <br /> ydraulic cure and self <br />cross-linking <br />• Rapid reactive setting, practically <br />climate independent <br />• Very low loss on drying <br />• After 3 hours resistant to rain and <br />foot traffic and ready for overcoating <br />• Can be applied by brush, trowel or <br />with suitable spray equipment <br />• Bonds to damp cementitious <br />substrates without priming <br />• Simple effective application <br />• Flexible and crack-bridging <br />• Suitable for all sound, loadbearing <br />conventional substrates used in <br />construction <br />• For interior and exterior use</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 · D-32760 Detmold <br />14 <br />2 04208 <br />EN 14891 <br />AQUAFIN-RS300 <br />Liquid-applied water impermeable <br />cement-based product for use beneath <br />ceramic tiling in external areas <br />EN 14891: CM <br />Initial tensile adhesion strength: </p> <p>≥ 0.5 N/mm²</p> <p>Tensile adhesion strength <br />after water contact: <br />after heat aging: <br />after freeze/thaw cycles: <br />after contact with lime water: </p> <p>≥ <br />≥ <br />≥ <br />≥</p> <p>Water impermability: <br />Crack bridging: </p> <p>0.5 <br />0.5 <br />0.5 <br />0.5</p> <p>Product application: <br />Place approx. 50–60 % liquid component into a clean mixing bucket and <br />stir in the powder until a homogenous, lump free mix is achieved. A mixing <br />time of approx. 2-3 minutes is necessary when mixing with power tools <br />(approx. 500-700 rpm). Add the remaining liquid component afterwards. <br />Depending on the method of application, up to a maximum of 1.5% clean <br />water (0.5 l/35 kg) can be added to AQUAFIN-RS300. <br />1. Prepare the substrate appropriate to its requirements. <br />2. Pre-wet the cementitious substrate so that it is matt damp at the time the <br />AQUAFIN-RS300 is applied. Prime very porous and slighty sanded <br />substrates with ASO-Unigrund. Allow the primer to dry before successive <br />work steps. <br />3. Apply a minimum of two coats of AQUAFIN-RS300 by brush or trowel. <br />Only apply the second and successive coats once the one beneath will <br />not be damaged by foot traffic or during application (approx. 4-6 hours, <br />depending on environmental conditions). An even thickness is achieved <br />by using a 4 to 6 mm notched trowel followed by smoothing flat. Avoid <br />applying thicknesses greater than 3 kg/m² as a single coat as there is a <br />risk of cracks appearing in the waterproof layer due to the high binder <br />content. Alternatively AQUAFIN-RS300 can be spray applied with <br />suitable equipment such as e.g. HighPump M8 (Peristaltic pump), <br />HighPump Small or HighPump Pictor (screw feed pump). Information on <br />the above can be obtained from HTG HIGH TECH Germany GmbH. <br />4. For forming water impermeable movement and connecting joints use the <br />ASO-Joint-Tape system. Using a 4-6 mm notched trowel, apply <br />AQUAFIN-RS300 to both sides of the joint to be bridged to a min. 2 cm <br />wider than the Joint-Tape. Lay the ASO-Joint-Tape system into the wet <br />coat and then thoroughly press down into the waterproofing coat with a <br />steel trowel or hard roller, without voids or folds. Ensure that a solid bed <br />and complete wetting is achieved as far as possible. Bonding must be <br />carried out in such a way as to exclude water migration around the <br />back of the ASO- Joint-Tape system. Lay the Joint-Tape system in a loop <br />over movement joints. Overlap Joint-Tape ends by min. 5 to 10 cm fully <br />bonded with AQUAFIN-RS300 without voids or folds, then overcoat. <br />5. Floor drains should have a thin-bed flange of a minimum circumferential <br />width of 5 cm to take the ASO-Joint-Sleeve and consist of suitable <br />materials for bonding, such as e.g. stainless steel, gun metal or PVC-U. <br />6. Thin-bed bonding of the tiles is carried out with polymer modified <br />adhesives such as e.g. AK7P, MONOFLEX-XL, SOLOFLEX, <br />UNIFIX-2K/6 etc.</p> <p>N/mm² <br />N/mm² <br />N/mm² <br />N/mm²</p> <p>no water penetration <br />≥ 0.75 mm</p> <p>* Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p>
