AQUAFIN-OS_201403_Englisch.pdf
4 Pages
964 KB
Download
<h1>AQUAFIN-OS_201403_Englisch.pdf</h1> <p>Technical data sheet <br />AQUAFIN®-OS <br />Crack-bridging, cementitious surface protection system (OS 5b)</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>201403001</p> <p>30 kg, set (2 component)</p> <p>Grey</p> <p>50,000</p> <p>1,000</p> <p>A-component: 20 kg, bag</p> <p>50,000</p> <p>1,000</p> <p>B-component: 10 kg, canister</p> <p>50,000</p> <p>1,000</p> <p>Fields of application / waterproofing <br />OS5b surface protection system for underground garages and multi-storey car parks <br />Protective coating against chloride attack and carbonation according to DIN 1504-2 <br />Renovation and protection of concrete surfaces prone to cracking <br />For newbuild and renovation <br />for interior and exterior use</p> <p>Product features <br />watertight <br />high resistance to freeze-thaw cycles and de-icing salt <br />CO2 and chloride barrier <br />For cementitious substrates <br />Approved surface protection system according to OS 5b and EN 1504-2</p> <p>Advantages <br />Crack bridging at -20 °C <br />Chloride-resistant <br />UV-resistant <br />Protects against carbonation <br />protects against chloride ingress</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/4</p> <p>02/06/2026</p> <p>Technical data sheet <br />AQUAFIN®-OS <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Consistency <br />Tensile adhesion strength DIN EN 1542 <br />Rainproof <br />Crack bridging DIN EN 1062-7</p> <p>Water vapour permeability, SD <br />CO₂ permeability, SD <br />Classification of the reaction to fire in accordance with DIN EN 13501-1</p> <p>2 component system <br />Polymer-mortar combination <br />Filler consistency <br />≥ 0.8 N/mm² <br />4 hours <br />static: Class A4 (2.0 mm) at +20 °C <br />dynamic: Class B2 at -20 °C and after 2000 h of UV <br />weathering: 0.10 - 0.15 mm (1000 cycles) Procedure B <br />Class I > 50 m <br />> 200 m <br />E</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B <br />Mixing time <br />Maturing time</p> <p>2 parts by weight (powder) <br />1 weight fraction (fluid) <br />approx. 3 minutes <br />approx. 2 minutes</p> <p>Application <br />Substrate/application temperature <br />Pot life <br />Method of application, max. layer thickness per application step <br />Consumption after OS5b and EN 1504-2 <br />Consumption pro m² and mm layer thickness <br />Overcoat after</p> <p>approx. 5 - 30 °C <br />approx. 30 minutes <br />up to 3 mm <br />approx. 5.5 kg/m² <br />approx. 1.8 kg <br />approx. 3 hours</p> <p>Processing equipment <br />Aids/tools <br />Stirrer (approx. 500-700 rpm) <br />Suitable mixing paddle <br />Trowel <br />Serrated or layer-thickness trowel <br />Flat trowel <br />Brush <br />Spray equipment</p> <p>Manual processing <br />Can be trowelled off <br />Applicable with a brush</p> <p>Machine application <br />AQUAFIN®-OS can be mechanically applied. For precise information, see the additional Technical Information No. 43.</p> <p>Suitable substrate <br />Concrete with a tensile adhesion strength of 1.5 N/mm² <br />Masonry work <br />Plasters P II and P III</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/4</p> <p>02/06/2026</p> <p>Technical data sheet <br />AQUAFIN®-OS <br />Preparing the substrate <br />Requirement for substrate <br />1. Even <br />2. Free of adhesion inhibiting substances <br />3. Sealed in the surface <br />4. Pore open <br />5. Load-bearing <br />6. Extensively fully grouted</p> <p>Preparing the surface <br />1. In the case of substrates damaged by de-icing salt, the substrate must be removed down to the neutral area, e.g. by means of milling, etc. <br />2. Pre-moisten the dry substrate so that it is matt damp at the time of application. <br />3. Extremely absorbent and slightly sandy substrates must be primed with AQUAFIN-Primer. <br />4. Moisture penetration from the rear and intermittent moisture loading from the negative side must be avoided.</p> <p>Application <br />Mixing <br />1. Put the liquid component into a clean mixing bucket and mix with the powder component to produce a homogeneous, lump-free mass. <br />2. The mixing time is ca. 3 minutes. <br />3. After a settling period of ca. 2 minutes, thoroughly homogenise the compound again.</p> <p>Application <br />1. Apply AQUAFIN®-OS as scratch coat and contact layer before first application. <br />2. Immediately afterwards, the first layer of sealant is applied wet-on-wet. <br />3. The second application step (and following) can take place when the first application step can no longer be damaged by reworking. (see <br />“Technical Data > Application”) <br />4. The waiting time between layers depends on temperature, humidity and other ambient conditions.</p> <p>Cleaning tools <br />Clean tools thoroughly with water after use.</p> <p>Notes <br />Protect surfaces that are not to be treated from the effects of AQUAFIN®-OS! <br />AQUAFIN®-OS as a surface coating must not be exposed to point or linear loads. <br />AQUAFIN®-OS may be plastered and coated with vapour permeable, solvent-free dispersion facade paints or dispersion silicate paints (not <br />pure silicate paints). Silicon resin paints and acrylate-based paints may also be used. <br />On PVC, gunmetal, and stainless steel flanges, ASO®-Dichtmanschetten or alternatively ADF®-Pipe-Gasket must be installed without voids or <br />wrinkles and integrated seamlessly into the waterproofing. <br />In case of strong sunlight, work against the movement of the sun in shaded areas. <br />Direct contact with metals such as copper, zinc, and aluminium must be avoided by means of a pore sealed primer. A pore-sealed primer is <br />produced via 2 application steps using ASODUR®-GBM (see technical data sheet). <br />In rooms with high humidity and/or insufficient ventilation (e.g. water containers), dropping below the dew point (condensation formation) <br />may occur on the surface. This must be avoided by taking suitable measures such as by using condensation dryers. Direct heating or <br />uncontrolled blowing warm air is not permitted. <br />The waterproofing must not be affected by water during binding. The effect of water from behind can lead to spalling in case of frost.</p> <p>Observe applicable safety data sheet!</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/4</p> <p>02/06/2026</p> <p>Technical data sheet <br />AQUAFIN®-OS <br />Explanations <br />Conformity / Declaration / Verification</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/4</p> <p>02/06/2026</p>
