INDUFLEX-PU_206415_Englisch.pdf
5 Pages
1.7 MB
Download
<h1>INDUFLEX-PU_206415_Englisch.pdf</h1> <p>Technical data sheet <br />INDUFLEX-PU <br />Elastic 1 component-PU jointing compound</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>206415001</p> <p>600 ml tubular bag, box</p> <p>Grey</p> <p>288</p> <p>6</p> <p>Areas of application / surface protection <br />for the elastic waterproofing of floor, connection and wall joints <br />in storage and production halls, yard areas <br />for joint widths From 10 mm to 30 mm <br />for interior and exterior use</p> <p>Product features <br />Good chemical and mechanical resistance <br />Higher tear resistance approx. 9.0 N/mm² <br />Frost-resistant and ageing-resistant <br />pigmented <br />temperature-resistant from - 40 °C to + 80 °C <br />suitable for load class A</p> <p>Advantages <br />Elastic and UV-resistant <br />Ready to use <br />total permissible deformation: 25% <br />no training requirement due to the low content of free monomeric diisocyanates (<0.1%)</p> <p>Existing test certificates <br />CE mark and declaration of performance in accordance with DIN EN 15651-4:2012</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/5</p> <p>12/03/2026</p> <p>Technical data sheet <br />INDUFLEX-PU <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Density, ready to use product (ISO 1183-1) <br />Recovery capacity (ISO 7389) <br />Shore-A hardness (ISO 868) <br />Temperature resistance <br />Deformation (DIN EN ISO 11600) <br />Viscosity, ready to use product <br />Water pollution class (WGK) <br />Permissible total deformation (DIN EN ISO 11600)</p> <p>Ready to use <br />Polyurethane (moisture curing) <br />approx. 1.3 g/cm³ <br />> 90 % <br />approx. 40 <br />- 40 + 80 °C <br />25 % <br />Filler consistency <br />1 (Selbsteinstufung) <br />max. 25 %</p> <p>Application <br />approx. 5 - 40 °C <br />80 % <br />min. 5 °C <br />approx. 10 mm <br />approx. 35 mm <br />Joint width (mm) × filling depth of jointing compound (mm) = <br />required quantity of jointing compound (ml) per linear metre of <br />joint. <br />min. 60 - 90 minutes</p> <p>Substrate temperature <br />Max. relative humidity <br />Minimum reaction temperature <br />Joint width min. <br />Joint width max. <br />Consumption</p> <p>Skin formation time</p> <p>Material rate <br />Material consumption rate according to the area of application <br />Consumption table for INDUFLEX-PU: Joint width x joint depth in a ratio of 1:0.8 based on IVD data sheet 1 <br />Joint width in mm</p> <p>Joint depth in mm</p> <p>Consumption of joint sealant over 1 m length</p> <p>10</p> <p>10</p> <p>approx. 100 ml</p> <p>15</p> <p>12</p> <p>approx. 180 ml</p> <p>20</p> <p>16</p> <p>approx. 320 ml</p> <p>25</p> <p>20</p> <p>approx. 500 ml</p> <p>30</p> <p>25</p> <p>approx. 750 ml</p> <p>The stated consumption quantities are approximate. There may be deviations depending on the property. We recommend creating test areas.</p> <p>Processing equipment <br />Aids/tools <br />Smooth wood <br />Cartridge gun <br />Brush <br />Industrial vacuum cleaner <br />Closed-cell and rot-resistant backing cord, approx. 20% larger than the joint width <br />Stirrer (approx. 300 rpm) <br />Circular cage <br />PSA</p> <p>Manual processing <br />Can be smoothed with a smoothing tool</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/5</p> <p>12/03/2026</p> <p>Technical data sheet <br />INDUFLEX-PU <br />Preparing the substrate <br />Requirement for substrate <br />1. Dry <br />2. Load-bearing <br />3. Firm <br />4. Grippy <br />5. Protected from moisture penetration from the rear <br />6. Free from adhesion inhibiting substances such as oil, dust, loose components, cement slurry, paints, hydrophobising agents, anti-graffiti coatings <br />7. smooth surfaces must be degreased with a suitable solvent</p> <p>Measures for substrate preparation <br />Substrate preparations must be carried out in compliance with DIN EN 14879-1:2005, 4.2 et.seq.</p> <p>Substrate quality class</p> <p>Preparing the details <br />In the case of building components which vehicles drive on, prepare the joint edges for the casting by chamfering them with a 45° chamfer with <br />a chamfer edge of approx. 5 mm. The chamfer must not be filled. General standard of joint width to joint depth (sealant thickness) = 1:0.8 or 1: <br />1.</p> <p>Application <br />Application <br />1. Insert a closed-cell backfill cord into the prepared joint space without damaging it. <br />2. Before grouting, protect the joint edge areas with adhesive tape. <br />3. Prime the joint flanks with ASODUR®-SG3-superfast before sealing the joint (see valid technical data sheet ASODUR®-SG3-superfast). <br />4. INDUFLEX-PU is applied with a suitable cartridge gun. The joint sealant must be applied free of bubbles and voids and must have complete <br />contact with the joint edges. <br />5. If necessary, level the joint surface within the pot life by lightly brushing over with the smoothing wood or a soft brush using a smoothing agent. <br />6. Strike off the joint compound with a suitable smoothing tool, pressing on the joint edges and the backfill.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 5 - 25 °C for 15 months in the original canister. Promptly use opened container.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/5</p> <p>12/03/2026</p> <p>Technical data sheet <br />INDUFLEX-PU <br />Notes <br />The indicated consumption quantities are calculated values without additions for textured surface roughness and absorbency, level <br />compensation and residual material in the container. We always recommend a calculated safety addition of 10% on top of the calculated <br />consumption quantities. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. <br />The bonding between the individual layers can be strongly disrupted between the individual application steps due to the effects of dampness <br />and contamination. Coating work requires a substrate temperature of at least 3 °C above the dew point temperature. <br />INDUFLEX-PU must not be used in swimming pool areas and for sealing glass. <br />INDUFLEX-PU may not be used on polyethylene, polypropylene, Teflon, polystyrene and bituminous substrates <br />INDUFLEX-PU must not be painted over. <br />Hard cleaning brushes used for mechanical cleaning can destroy the joint <br />Slight colour differences, caused by different production batches and raw material fluctuations, are unavoidable. Neighbouring surface <br />sections should be coated using the same production batch (same batch no. on the delivered packaging). <br />Effects of the environment and external influences can lead to colour changes, but these have no effect on the functionality of the jointing <br />compound. <br />No discoloration on natural stones, please carry out tests before application <br />Protect from the effects of dirt and moisture during the curing phase. <br />The hardening time until full loadability is 14 days at approx. +20 °C. 80% of the final hardness, according to Shore A, is reached after 2 <br />days at +23 °C <br />Observe the technical data sheets of the products mentioned before starting work. <br />Applications that have not been clearly mentioned in this technical data sheet may only be carried out after the technical service department <br />of SCHOMBURG GmbH has been consulted, and after the said department has approved of such a course of action in writing.</p> <p>Relevant regulations <br />The recognised standards of construction engineering, the relevant guidelines and current regulations <br />must be observed. <br />Observe applicable safety data sheet! <br />Explanations <br />Conformity / Declaration / Verification</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/5</p> <p>12/03/2026</p> <p>Technical data sheet <br />INDUFLEX-PU <br />Chemical durability</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />5/5</p> <p>12/03/2026</p>
