ASODUR-V2260_205066_Englisch.pdf
5 Pages
1.03 MB
Download
<h1>ASODUR-V2260_205066_Englisch.pdf</h1> <p>Technical data sheet <br />ASODUR®-V2260 <br />2 component polyurethane sealant, glossy</p> <p>Material number</p> <p>Contents</p> <p>Unit of quantity</p> <p>Colour</p> <p>205066001</p> <p>5</p> <p>KG</p> <p>Transparent</p> <p>Areas of application / surface protection <br />As surface protection on cementitious and reactive resin-bound substrates <br />For interior</p> <p>Product features <br />Two component <br />aqueous <br />light-fast and UV-stable <br />chemical-resistant <br />Good migration resistance <br />Very low emission - EMICODE® EC 1PLUS <br />Fulfils AgBB formula requirements</p> <p>Advantages <br />Solvent free <br />Transparent <br />Can be adjusted for slip resistance <br />Good scratch resistance <br />Good abrasion resistance <br />Easy to clean <br />no training requirement due to the low content of free monomeric diisocyanates (<0.1%)</p> <p>Existing test certificates <br />CE mark and declaration of performance in accordance with DIN EN 1504-2 <br />CE mark and declaration of performance in accordance with DIN EN 13813</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/5</p> <p>14/05/2025</p> <p>Technical data sheet <br />ASODUR®-V2260 <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Density, ready to use product (ISO 1183-1) <br />Viscosity A-component (DIN EN ISO 2884-1) <br />Viscosity B-component (DIN EN ISO 2884-1) <br />Vapour diffusion behaviour</p> <p>2 component system <br />polyurethane resin <br />approx. 1.05 g/cm³ <br />50 - 80 mPas (+ 23 °C / 50% relative humidity) <br />1640 - 2440 mPas (+ 23 °C / 50% relative humidity) <br />Vapour diffusion-inhibiting</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B <br />Mix ratio, addition of ASO-Antislide slip resistance <br />Mixing time <br />Maturing time <br />Water addition (percentage)</p> <p>100 weight proportion <br />20 weight proportion <br />10 % <br />approx. 3 minutes <br />approx. 2 minutes <br />approx. 5 %</p> <p>Application <br />Substrate temperature <br />Max. relative humidity <br />Minimum reaction temperature <br />Mixing method, machines, tools <br />Overcoat and walkable after</p> <p>Consumption (non-absorbent substrates) <br />Consumption (absorbent substrates) <br />Consumption (sealing coat, slip-resistant) <br />Pot life <br />Application temperature <br />Hardening time / full resilience</p> <p>approx. 10 - 30 °C <br />80 % <br />min. 10 °C <br />Drill with stirrer <br />Min. 2 - 3 hours, max. 12 hours at + 30 °C <br />Min. 4 - 15 hours, max. 24 hours at + 20 °C <br />Min. 24 - 36 hours, max. 48 hours at + 10 °C <br />80 - 150 g/m² per layer <br />200 - 250 g/m² per layer <br />approx. 120 g / m² <br />approx. 25 - 35 minutes <br />approx. 10 - 30 °C <br />approx. 7 days</p> <p>Processing equipment <br />Aids/tools <br />Nylon fur roller (6mm) with textured polyamide cover <br />Stirrer <br />Circular cage <br />PSA</p> <p>Manual processing <br />Can be applied with a nylon fur roller <br />Distributable with nylon fur roller</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/5</p> <p>14/05/2025</p> <p>Technical data sheet <br />ASODUR®-V2260 <br />Preparing the substrate <br />Requirement for substrate <br />1. Dry (moisture content ≤ 4 CM-%) <br />2. Load-bearing <br />3. Firm <br />4. Grippy <br />5. dust-free <br />6. Protected from moisture penetration from the rear <br />7. Free of adhesion inhibiting substances <br />8. Open-pored after mechanical substrate preparation</p> <p>Measures for substrate preparation <br />Substrate preparations must be carried out in compliance with DIN EN 14879-1:2005, 4.2 et.seq.</p> <p>Application <br />Mixing <br />1. The (ideal) material temperature during the mixing procedure is +15 °C. <br />2. Homogenise the resin in the original container by shaking. <br />3. Pour the homogenised resin into a clean mixing container. <br />4. The resin must run out of the container completely. <br />5. Add the hardener to the resin. <br />6. The hardener must run completely out of the container. <br />7. Mix thoroughly with the mixer until a homogeneous consistency. <br />8. The hardener must be distributed evenly. <br />9. The mixing time is ca. 3 minutes. <br />10. Let the homogenised mixture stand for about 2 minutes. <br />11. Decant the mass into a clean bucket. <br />12. Stir carefully again.</p> <p>Application <br />1. ASODUR®-V2260 is applied in a single application step. <br />2. The mixed material is poured onto the surface in portions. <br />3. Spread evenly over the surface with the fur roller in a criss-cross pattern and level. <br />4. Minimise overlaps as far as possible. <br />5. The ASODUR® coatings that are to be sealed should not be older than 24 hours.</p> <p>Slip-resistant setting <br />1. In the mixed ASODUR®-V2260 add approx. 8-10 wt.% of ASO®-Antislide homogeneously stirred in. <br />2. The mixed material is poured onto the surface in portions. <br />3. Spread evenly with the fur roller in a criss-cross pattern and level.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 10 - 30 °C for 12 months in the original canister. Promptly use opened container.</p> <p>Disposal <br />Hardened product leftovers can be disposed of in household waste.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/5</p> <p>14/05/2025</p> <p>Technical data sheet <br />ASODUR®-V2260 <br />Notes <br />The indicated consumption quantities are calculated values without additions for textured surface roughness and absorbency, level <br />compensation and residual material in the container. We always recommend a calculated safety addition of 10% on top of the calculated <br />consumption quantities. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. The rate at which material is <br />consumed also increases at lower temperatures. <br />The bonding between the individual layers can be strongly disrupted between the individual application steps due to the effects of dampness <br />and contamination. Coating work requires a substrate temperature of at least 3 °C above the dew point temperature. <br />If longer waiting times arise between the individual application steps or surfaces that have already been treated with liquid resin are coated <br />again after an extended period of time, the old surface must be well cleaned and thoroughly roughened. Then apply a complete pore-free <br />new coating. <br />Ensure there is good ventilation during the drying and hardening phases. <br />After they have been applied, surface protection systems must be protected against dampness (e.g. rainwater, condensation water) for <br />approx. 4–6 hours. Moisture causes a white colour and/or stickiness on the surface and can cause problems during hardening. Discoloured <br />and/or sticky surfaces must be removed and reworked, e.g. through grinding or shot blasting. <br />Observe the technical data sheets of the products mentioned before starting work. <br />Applications that have not been clearly mentioned in this technical data sheet may only be carried out after the technical service department <br />of SCHOMBURG GmbH has been consulted, and after the said department has approved of such a course of action in writing. <br />The possible formation of microbubbles in the first sealing layer can be reduced by applying a second layer within 24 hours. <br />Dips < 5 mm should be levelled with ASOCRET-M30. <br />Puddles of water can lead to white discolouration on the hardened sealing layer. The formation of puddles should be avoided. <br />Diluting ASODUR-V2260 with water can possibly lead to increased orange peel effect. <br />The statements are made on the basis of extensive testing and practical experience. They are not transferable to every application. We <br />therefore recommend performing trials if necessary. We reserve the right to make technical changes in connection with further developments.</p> <p>Relevant regulations <br />The recognised standards of construction engineering, the relevant guidelines and current regulations <br />must be observed. <br />Observe applicable safety data sheet! <br />GISCODE: PU40 <br />Explanations <br />Conformity / Declaration / Verification</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/5</p> <p>14/05/2025</p> <p>Technical data sheet <br />ASODUR®-V2260 <br />Chemical durability</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />5/5</p> <p>14/05/2025</p>
