ASODUR-K900_205070_Englisch.pdf
4 Pages
896 KB
Download
<h1>ASODUR-K900_205070_Englisch.pdf</h1> <p>Technical data sheet <br />ASODUR®-K900 <br />Casting and adhesive resin</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>205070001</p> <p>1kg, kneading bag</p> <p>yellowish transparent</p> <p>250,000</p> <p>5,000</p> <p>205070002</p> <p>0.5kg, kneading bag</p> <p>yellowish transparent</p> <p>350,000</p> <p>5,000</p> <p>Areas of application <br />As casting resin for “nailing” wide cracks with screed clamps <br />For non-positive sealing of cracks and joints <br />for producing levelling and scratch coats <br />for producing epoxy resin coating <br />Suitable for heated substrates</p> <p>Product features <br />Two component <br />Solvent free <br />Water and frost resistant <br />chemical-resistant <br />Low viscosity <br />Very good penetration characteristics <br />Rapid setting</p> <p>Advantages <br />Easy and clean application - without tools <br />In a kneading bag <br />Outstanding bonding on concrete, screed, stone, etc. <br />Including disposable gloves and screed clamps</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/4</p> <p>21/04/2026</p> <p>Technical data sheet <br />ASODUR®-K900 <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Density (spec. weight) <br />Viscosity, ready to use product [value]</p> <p>2 component system <br />Epoxy resin <br />approx. 1.1 g/cm³ <br />approx. 360 mPa*s</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B <br />Mix ratio, addition of quartz sand mortar (Ø 0.06–1.5 mm) <br />Mix ratio, addition of quartz sand (Ø 0.1 – 0.6 mm) <br />Mixing time</p> <p>2 weight proportion <br />1 Gewichtsanteil <br />approx. 8.3 weight proportion <br />1 Gewichtsanteil <br />approx. 3 minutes</p> <p>Application <br />approx. 10 - 35 °C <br />Substrate temperature <br />80 % <br />Max. relative humidity <br />approx. 12 minutes <br />Pot life <br />min. 10 °C <br />Minimum reaction temperature <br />approx. 1.1 kg/l <br />Consumption <br />Consumption per mm layer thickness (levelling and scratch coat with quartz sand) approx. 1.6 kg/m² <br />approx. 2 kg/m² <br />Consumption (epoxy resin mortar mixture per mm layer thickness) <br />approx. 10 - 35 °C <br />Application temperature <br />approx. 4 hours <br />Overcoat after</p> <p>Processing equipment <br />Aids/tools <br />Filler</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Load-bearing <br />2. Firm <br />3. Grippy <br />4. Dry <br />5. Free of adhesion inhibiting substances <br />6. Protected from the effects of moisture penetration on the rear side</p> <p>Measures for substrate preparation <br />Substrate preparations must be carried out in compliance with DIN EN 14879-1:2005, 4.2 et.seq.</p> <p>Substrate quality class</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/4</p> <p>21/04/2026</p> <p>Technical data sheet <br />ASODUR®-K900 <br />Application <br />Mixing <br />1. The (ideal) material temperature during the mixing procedure is +15 °C. <br />2. Pull the separating clamps out of the two-chamber segment and allow both components to run into each other. <br />3. Knead and churn the bag contents to form a homogeneous mass that is free of streaks. <br />4. The mixing time is ca. 3 minutes. <br />5. After mixing, open the screw top on the corner of the bag and squeeze the mass out.</p> <p>Crack filling <br />1. Depending on their length, open the cracks or joints to 1/2 to 2/3 of the screed thickness using a cut-off wheel. <br />2. Cut approx. 10 cm long transverse slits at right angles to the crack one after the other every 30 cm. <br />3. Then clean the cut areas meticulously with an industrial vacuum cleaner and remove any dust. <br />4. Apply the mixed casting resin to the cut joints until saturated. <br />5. Insert the screed clips provided into the transverse grooves. <br />6. Re-grouting may be necessary. <br />7. Use a spatula to remove excess material immediately. <br />8. After the gel phase has been reached, sprinkle the surface of the fresh casting resin completely with quartz sand (Ø 0.1–0.6 mm). <br />9. After hardening, vacuum off the unbound, loose quartz sand. <br />10. After approx. 4 hours, rework the hardened casting resin with sandpaper (e.g. 60 grain). Then thoroughly dedust the surface again.</p> <p>Filling voids <br />1. Make the area to be grouted accessible by exposing and/or drilling. <br />2. Clean the area thoroughly and remove dust. <br />3. Apply the mixed casting resin to the voids in portions. <br />4. Recasting may be necessary.</p> <p>Levelling of unevenness <br />1. Mix the quartz sand into the mixed and re-potted ASODUR®-K900 (at a mix ratio of 1:1). <br />2. Mix the liquid and solid components evenly. <br />3. Apply the mixed levelling compounds in a single application step using the scratch filler method. <br />4. While the layer is still fresh, apply quartz sand (Ø 0.1–0.6 mm).</p> <p>Producing and applying epoxy mortar as a levelling and coving mortar <br />1. Stir the quartz sand (Ø 0.06-1.5 mm) homogeneously into the mixed ASODUR®-K900 in a mix ratio of 3:25. <br />2. Prime the substrate with ASODUR®-K900. <br />3. Apply the mortar while still wet using trowel techniques, ensuring even compaction. <br />4. Observe the minimum film thickness of 3 mm.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 10 - 25 °C for 18 months in the original canister. Promptly use opened container.</p> <p>Notes <br />The indicated consumption quantities are calculated values without additions for textured surface roughness and absorbency, level <br />compensation and residual material in the container. We always recommend a calculated safety addition of 10% on top of the calculated <br />consumption quantities. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. <br />Only once the screed has reached its permissible residual moisture content, i.e. is ready for laying, should the screed cracks and crack <br />control joints be closed. <br />Observe the technical data sheets of the products mentioned before starting work. <br />Applications that have not been clearly mentioned in this technical data sheet may only be carried out after the technical service department <br />of SCHOMBURG GmbH has been consulted, and after the said department has approved of such a course of action in writing. <br />For detailed information on application, read and observe supplementary technical information no. 19 "Applying ASODUR products".</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/4</p> <p>21/04/2026</p> <p>Technical data sheet <br />ASODUR®-K900 <br />Relevant regulations <br />The recognised standards of construction engineering, the relevant guidelines and current regulations <br />must be observed. <br />Observe applicable safety data sheet!</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/4</p> <p>21/04/2026</p>
