ASO-Dichtmanschette-Wand_205937_Englisch.pdf
4 Pages
949 KB
Download
<h1>ASO-Dichtmanschette-Wand_205937_Englisch.pdf</h1> <p>Technical data sheet <br />ASO®-Dichtmanschette-Wand <br />Preformed waterproof sections for pipe penetrations in walls</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>205937001</p> <p>12x12cm, piece</p> <p>white with logo</p> <p>3000,000</p> <p>50,000</p> <p>Areas of use/bonded waterproofing <br />to integrate tap extensions and intersections into the bonded waterproofing system <br />as a system component for bonded waterproofing for water impact class W0-I to W3-I in accordance with DIN 18534</p> <p>Product features <br />Fleece-laminated wall collar <br />Tear resistant <br />Highly flexible and stretchy <br />Extra thin <br />Highly resistant <br />Crack bridging</p> <p>Advantages <br />Tested system product <br />Can be adjusted individually to the required diameter <br />High bonding to cementitious waterproofing slurry or polymer dispersions – thanks to fleece-laminated surface</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/4</p> <p>26/04/2026</p> <p>Technical data sheet <br />ASO®-Dichtmanschette-Wand <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Diameter (internal) <br />For pipe diameter <br />Burst pressure <br />Expansion, crosswise (DIN EN ISO 527-3) <br />UV-resistance after DIN EN ISO 4892-2 <br />Sd value</p> <p>Piece goods <br />Composite material: Fleece-membrane-fleece <br />approx. 16 mm <br />approx. 24 - 40 mm <br />≥ 1.5 bar <br />> 300 % <br />500 hours <br />>1m</p> <p>Sealing against pressing water until <br />Temperature resistance <br />Vapour diffusion behaviour</p> <p>1.5 bar <br />- 22 + 90 °C <br />Vapour diffusion inhibiting</p> <p>Application <br />Consumption</p> <p>1 unit per pipe penetration</p> <p>Processing equipment <br />Aids/tools <br />Serrated or layer-thickness trowel <br />Flat trowel <br />Brush <br />Pressure roller <br />Scissors/knife</p> <p>Suitable substrate <br />Dry screeds <br />Raised floors <br />Tile bearing elements <br />Firmly adhering tiled finishes <br />Bonded waterproofing <br />Concrete <br />Cement-based screed (CT)</p> <p>Floor levelling compounds <br />Calcium sulphate screeds (CA, CAF) <br />Mastic asphalt screeds (AS) <br />Magnesia screeds (MA) <br />Cement plaster <br />Gypsum plaster <br />Lime-cement plaster</p> <p>Light plaster</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Dry <br />2. Load-bearing <br />3. Even <br />4. Sealed in the surface <br />5. Free of cracks <br />6. Free from negative pressing water <br />7. Free of adhesion inhibiting substances</p> <p>Measures for substrate preparation <br />Instructions for substrate preparation can be found in the technical data sheet of the selected sealing material.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/4</p> <p>26/04/2026</p> <p>Technical data sheet <br />ASO®-Dichtmanschette-Wand <br />Application <br />Application <br />1. Clean and de-grease the pipe penetration. <br />2. Apply the selected waterproofing material to the prepared substrate. <br />3. The system design in wear class C is the same as described for the DENSARE system. <br />4. Choose a ASO®-Dichtmanschette-Wand that is suitable for the pipe diameter. The hole diameter of the sealing sleeve must be smaller than the <br />pipe diameter so that the sealing sleeve is pressed against the pipe penetration. <br />5. Widen the hole diameter of the sealing sleeve slightly and slip it over the pipe connection. Alternatively, if direct connection to the pipe is not <br />possible (blanking plugs mortared in), prepare the final assembly with ASO®-DMH (Joint-Sleeve-Installation tool). <br />6. Press the sealing sleeve into the waterproofing layer meticulously without voids or wrinkles, using a flat trowel or pressure roller. <br />7. 8. The sealing sleeve must be integrated into the area waterproofing seamlessly. A tight connection to the area waterproofing must be made.</p> <p>Storage conditions <br />Storage <br />Cool, dry, protected from sunlight. Min. 36 months in the original canister.</p> <p>Notes <br />Pipe penetrations that are secured with ASO®-Dichtmanschette-Wand must be protected adequately against mechanical damage. <br />ASO®-Dichtmanschette-Wand may not be glued or overcoated afterwards with products containing solvents.</p> <p>Relevant regulations <br />Planning, inspection of substrates and building site circumstances, laying, grouting and subsequent <br />care of the work must be done in accordance with the relevant DIN standards and recognised rules of <br />technology (e.g. the ZDB Data sheets of the Zentralverband Deutsches Baugewerbe e.V.(German <br />construction Association) in the latest version. <br />Explanations <br />Chemical durability</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/4</p> <p>26/04/2026</p> <p>Technical data sheet <br />ASO®-Dichtmanschette-Wand <br />Impact classes and typical applications in accordance with DIN 18534-1</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/4</p> <p>26/04/2026</p>
