ASODUR-V2370_206441_Englisch.pdf
5 Pages
1.16 MB
Download
<h1>ASODUR-V2370_206441_Englisch.pdf</h1> <p>Technical Datasheet <br />ASODUR®-V2370 <br />Sealing coating</p> <p>Material number</p> <p>Contents</p> <p>Unit of quantity</p> <p>Packaging</p> <p>Colour</p> <p>206441003</p> <p>15</p> <p>KG</p> <p>Combination packs</p> <p>≈ RAL 7032 pebble grey</p> <p>206441001</p> <p>15</p> <p>KG</p> <p>Combination packs</p> <p>Red</p> <p>206441002</p> <p>15</p> <p>KG</p> <p>Combination packs</p> <p>Black</p> <p>Product features <br />Two component <br />Solvent free <br />Resistant to weathering <br />high chemical resistance <br />Resistant to water, wastewater and seawater <br />Abrasion-resistant <br />Elastifying</p> <p>Advantages <br />Can be applied to vertical surfaces <br />pigmented <br />Sprayable <br />Stray current-insulating</p> <p>Areas of application / surface protection <br />As surface protection in sewage treatment plants, sewage pipes, biogas plants, steel sheet piles and digestion towers with cementitious <br />substrates <br />As surface protection on cementitious and reactive resin-bound substrates <br />Suitable for steel substrates <br />For interior and exterior use</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/5</p> <p>15/01/2024</p> <p>Technical Datasheet <br />ASODUR®-V2370 <br />Existing test certificates <br />CE mark and declaration of performance in accordance with DIN EN 1504-2</p> <p>Technical Data <br />Material properties <br />Product components <br />Base material <br />Density, ready to use product (ISO 1183-1) <br />Shore-A hardness (DIN ISO 7619) <br />Viscosity A-component (DIN EN ISO 2884-1) <br />Viscosity B-component (DIN EN ISO 2884-1)</p> <p>2 component system <br />Epoxy resin <br />approx. 1.37 g/cm³ <br />approx. 80 <br />5,250 - 7,880 mPas (+ 23 °C / 50% relative humidity) <br />110 - 160 mPas (+ 23 °C / 50% relative humidity)</p> <p>Mixing <br />Mix ratio, component A <br />Mix ratio, component B <br />Mixing time</p> <p>7 weight proportion <br />1 weight proportion <br />approx. 3 minutes</p> <p>Application <br />Substrate temperature <br />Max. relative humidity <br />Minimum reaction temperature <br />Mixing method, machines, tools <br />Overcoat and walkable after</p> <p>Consumption (non-absorbent substrates) <br />Consumption (absorbent substrates) <br />Pot life <br />Pot life</p> <p>Application temperature <br />Hardening time / full resilience</p> <p>from 10 °C to 30 °C <br />80 % <br />min. 10 °C <br />Drill with stirrer <br />Min. 6 - 8 hours, max. 12 hours at + 30 °C <br />Min. 24 - 36 hours, max. 48 hours at + 20 °C <br />Min. 9 - 13 hours, max. 48 hours at + 10 °C <br />400 - 500 g/m² per layer <br />250 - 400 g/m² per layer <br />approx. 0 - 0 minutes <br />22 - 28 minutes (+ 30 °C) <br />45 - 55 minutes (+ 20 °C) <br />90 - 110 minutes (+ 10 °C) <br />from 10 °C to 30 °C <br />3 days (+ 30 °C) <br />7 days (+ 20 °C) <br />10 days (+ 10 °C)</p> <p>Application technology <br />Aids/tools <br />Nylon fur roller (6mm) with textured polyamide cover <br />Stirrer <br />Circular cage <br />PSA <br />Mechanical grouting system (airless)</p> <p>Manual processing <br />Can be applied with a nylon fur roller <br />Distributable with nylon fur roller</p> <p>Machine application <br />ASODUR®-V2370 can be mechanically applied. For precise information, see the additional Technical Information No. 43.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/5</p> <p>15/01/2024</p> <p>Technical Datasheet <br />ASODUR®-V2370 <br />Substrate preparation <br />Requirement for substrate <br />1. <br />2. <br />3. <br />4. <br />5. <br />6. <br />7. <br />8. <br />9.</p> <p>Dry (moisture content ≤ 6 CM-%) <br />Load-bearing <br />Firm <br />Grippy <br />dust-free <br />Protected from moisture penetration from the rear <br />Free of adhesion inhibiting substances <br />Open-pored after mechanical substrate preparation <br />Iron and steel surfaces are rust-removed to standard purity level Sa 2.5 in accordance with DIN 55982</p> <p>Measures for substrate preparation <br />Substrate preparations must be carried out in compliance with DIN EN 14879-1:2005, 4.2 et.seq.</p> <p>Usage <br />Mixing <br />1. <br />2. <br />3. <br />4. <br />5. <br />6. <br />7. <br />8. <br />9.</p> <p>The (ideal) material temperature during the mixing procedure is +15 °C. <br />Mix the resin homogeneously in the original container. <br />Add the hardener to the resin. <br />The resin must run out of the container completely. <br />Mix thoroughly with the mixer until a homogeneous consistency. <br />The hardener must be distributed evenly. <br />The mixing time is ca. 3 minutes. <br />Decant the mass into a clean bucket. <br />Stir meticulously again.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 10 - 30 °C for 12 months in the original canister. Promptly use opened canister.</p> <p>Disposal <br />Hardened product leftovers can be disposed of in household waste.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/5</p> <p>15/01/2024</p> <p>Technical Datasheet <br />ASODUR®-V2370 <br />Notes <br />The indicated consumption quantities are calculated values without additions for textured surface roughness and absorbency, level <br />compensation, and residual material in the canister. We always recommend a calculated safety addition of 10% on top of the calculated <br />consumption quantities. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. The rate at which material is <br />consumed also increases at lower temperatures. <br />The bonding between the individual layers can be strongly disrupted between the individual application steps due to the effects of dampness <br />and contamination. Coating work requires a substrate temperature of at least 3 °C above the dew point temperature. <br />If longer waiting times arise between the individual application steps or surfaces that have already been treated with liquid resin are coated <br />again after an extended waiting time, the old surface must be well cleaned and thoroughly ground. Then apply a complete pore-free new <br />coating. <br />Arrange for proper ventilation during the drying and hardening phases. <br />After they have been applied, surface protection systems must be protected against dampness (e.g. rainwater, condensation water) for <br />approx. 4–6 hours. Moisture causes a white colour and/or stickiness on the surface and can cause problems during hardening. Discoloured <br />and/or sticky surfaces must be removed and reworked, e.g. through grinding or shot blasting. <br />To be assured of even double application, apply the sealant in two different colours. <br />If the reworking time is exceeded, the surface must be prepared for another application by sanding after it has hardened. <br />For larger surfaces, traces of accretions and overlap must be minimised. <br />It is imperative to rinse the mixing pump and the hoses in the event of work interruptions! <br />Observe the technical data sheets of the products mentioned before starting work. <br />Applications that have not been clearly mentioned in this technical data sheet may only be carried out after the technical service department <br />of SCHOMBURG GmbH has been consulted, and after the said department has approved of such a course of action in writing. <br />The statements are made on the basis of extensive testing and practical experience. They are not transferable to every application. We <br />therefore recommend performing trials if necessary. We reserve the right to make technical changes in connection with further developments.</p> <p>The recognised standards of construction engineering, the relevant guidelines and current regulations <br />must be observed. <br />Observe applicable safety data sheet! <br />Annotations <br />Conformity / Declaration / Verification</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/5</p> <p>15/01/2024</p> <p>Technical Datasheet <br />ASODUR®-V2370 <br />Chemical durability</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />5/5</p> <p>15/01/2024</p>
