Technical Datasheet ASO®-Dichtmanschette-B Joint sleeve floor for bonded waterproofing
Material number
Packaging
Colour
206138001
piece
Grey with SCHOMBURG logo
Product features Fleece-laminated floor collar Format: 45 cm x 45 cm Marked for precise cutting to the required diameter Flexible and stretchy Crack bridging
Advantages Tested system product Can be adjusted individually to the required diameter High bonding to cementitious waterproofing slurry or polymer dispersions thanks to fleece-laminated surface
Areas of use/bonded waterproofing To integrate floor drains and intersections into the bonded waterproofing system As a system component for bonded waterproofing for water impact class W0-I to W3-I in accordance with DIN 18534
Technical Data Material properties Product components Base material Burst pressure Reaction to fire in accordance with DIN EN 4102 Sd value in accordance with DIN EN 1931 Vapour diffusion behaviour
Piece goods TPE Composite material: Fleece-membrane-fleece ≥ 1.5 bar B2 > 14 m ± 7 m Vapour diffusion-inhibiting
Application Consumption
1 unit per pipe penetration
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 1/3
29/06/2023
Technical Datasheet ASO®-Dichtmanschette-B Application technology Aids/tools Serrated or layer-thickness trowel Flat trowel Brush Pressure roller Scissors/knife
Suitable substrate Dry screeds Raised floors Tile bearing elements Firmly adhering tiled finishes Concrete, cement screed (CT), floor levelling compounds, calcium sulphate screeds (CA, CAF), mastic asphalt screeds (AS), magnesia screeds (MA) Cement-based plaster, gypsum plaster, cement-lime plaster, lightweight plaster Bonded waterproofing; the suitability of the substrate must be checked and observed, taking into account the planned water impact class of DIN 18534 and DIN 18531.
Substrate preparation Requirement for substrate 1. 2. 3. 4. 5. 6. 7.
Dry Load-bearing Even Sealed in the surface Free of cracks Free from negative pressing water Free of adhesion inhibiting substances
Measures for substrate preparation Instructions for substrate preparation can be found in the technical data sheet of the selected sealing material.
Usage Application 1. Lay ASO®-Dichtmanschette-B over the floor drain flange. 2. Mark out the size of the flange and cut out the required opening. 3. Clean and degrease the flange. On flanges with a surface made of stainless steel for example, additional primer made of reaction resin such as ASODUR®-GBM may be required. 4. Apply the selected waterproofing material to the prepared substrate. 5. Pull the sealing sleeve over the flange. 6. Press the sealing sleeve into the waterproofing layer meticulously without voids or wrinkles, using a flat trowel or pressure roller. 7. The sealing sleeve must be integrated into the area waterproofing seamlessly. A tight connection to the area waterproofing must be made.
Storage conditions Storage Cool, dry, protected from sunlight. Min. 24 months in the original container.
Disposal Product leftovers can be disposed of in household waste.
Emission behaviour / building certification systems Very low emissions in accordance with GEV-EMICODE, which normally results in positive evaluations within the scope of building certification systems in accordance with DGNB, LEED, BREEAM, HQE. Maximum quality level 4, line 8 in accordance with DGNB criteria "ENV 1.2 Risks to the local environment".
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 2/3
Technical Datasheet ASO®-Dichtmanschette-B Notes Pipe penetrations that are secured with ASO®-Dichtmanschette-B must be protected adequately against mechanical damage. ASO®-Dichtmanschette-B may not be glued or overcoated afterwards with products containing solvents. Border, field, structural movement joints and movement joints should be carried over to or installed at the designated location; suitable means (e.g. edge strips) should be used to detach them!
Planning, inspection of substrates and building site circumstances, laying, grouting and subsequent care of the work must be done in accordance with the relevant DIN standards and recognised rules of technology (e.g. the ZDB sheets of the Zentralverband Deutsches Baugewerbe e.V.) in the latest version.
The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 3/3