Technical Datasheet ASO®-Gefälleecke Bonded waterproofing in combination with tiled finishes
Material number
Angle / installation position
Width, article
Contents
Packaging
Colour
206134001
90° left
20 mm
1 piece
piece
Grey with SCHOMBURG logo
206134002
28 mm
206134003
90° right
206134004
Product features Fleece-laminated slope corner Left and right version Height compensation at 20 mm and 28 mm Flexible and stretchy Crack bridging
Advantages Tested system product Reliable integration of height differences in slope situations High bonding to cementitious waterproofing slurry or polymer dispersions thanks to fleece-laminated surface
Areas of use/bonded waterproofing To design the bonded waterproofing effectively in slope situations As a system component for bonded waterproofing for water impact class W0-I to W3-I in accordance with DIN 18534
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 1/3
17/08/2023
Technical Datasheet ASO®-Gefälleecke Technical Data Material properties Product components Base material Burst pressure Reaction to fire in accordance with DIN EN 4102 Sd value in accordance with DIN EN 1931 Temperature resistance Vapour diffusion behaviour
Piece goods TPE Composite material: Fleece-membrane-fleece ≥ 1.5 bar B2 > 14 m ± 7 m - 30 + 90 °C Vapour diffusion-inhibiting
Application Consumption
approx. 1 m per m
Application technology Aids/tools Serrated or layer-thickness trowel Flat trowel Brush Pressure roller Scissors/knife
Suitable substrate Dry screeds Raised floors Tile bearing elements Firmly adhering tiled finishes Concrete, cement screed (CT), floor levelling compounds, calcium sulphate screeds (CA, CAF), mastic asphalt screeds (AS), magnesia screeds (MA) Cement-based plaster, gypsum plaster, cement-lime plaster, lightweight plaster Bonded waterproofing; the suitability of the substrate must be checked and observed, taking into account the planned water impact class of DIN 18534 and DIN 18531.
Substrate preparation Requirement for substrate 1. 2. 3. 4. 5. 6. 7.
Dry Load-bearing Even Sealed in the surface Free of cracks Free from negative pressing water Free of adhesion inhibiting substances
Measures for substrate preparation Instructions for substrate preparation can be found in the technical data sheet of the selected sealing material.
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 2/3
Technical Datasheet ASO®-Gefälleecke Usage Application 1. Apply the waterproofing material to both sides of the joint or wall transition to be bridged, at least 2 cm wider than the joint sealing tape that is used (e.g. using a 4–6 mm notched trowel). 2. Press the ASO®-Gefälleecke into the waterproofing layer meticulously without voids or wrinkles, using a flat trowel or pressure roller. 3. The joint sealing tape must be seamlessly integrated into the area waterproofing. 4. Bond joint-tape edges or connections with the waterproofing material without wrinkles, covering the whole area, and overcoat after. 5. Joint-tape edges or connections to pre-formed pieces are applied with an overlap of at least 5 cm. 6. For structural movement joints, ASO®-Gefälleecke is inserted into the joint and the fresh layer in the form of a loop. 7. For structural movement joints/movement joints, the pre-formed pieces are inserted into the joint and the fresh layer in the form of a loop.
Storage conditions Storage Cool, dry, protected from sunlight. Min. 24 months in the original container.
Disposal Product leftovers can be disposed of in household waste.
Emission behaviour / building certification systems Very low emissions in accordance with GEV-EMICODE, which normally results in positive evaluations within the scope of building certification systems in accordance with DGNB, LEED, BREEAM, HQE. Maximum quality level 4, line 8 in accordance with DGNB criteria "ENV 1.2 Risks to the local environment".
Notes Remove adhesive strips from any existing interfaces of the joint tape roll. Establish the connection area overlapping. Joints that are secured with ASO®-Gefälleecke must be adequately protected against mechanical damage! ASO®-Gefälleecke may not be glued or overcoated afterwards with products containing solvents. Border, field, structural movement joints and movement joints should be carried over to or installed at the designated location; suitable means (e.g. edge strips) should be used to detach them!
Planning, inspection of substrates and building site circumstances, laying, grouting and subsequent care of the work must be done in accordance with the relevant DIN standards and recognised rules of technology (e.g. the ZDB sheets of the Zentralverband Deutsches Baugewerbe e.V.) in the latest version.
The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.
SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com 3/3