ASO-DB-Standard_Product_information_GB_0816.pdf
2 Pages
148 KB
Download
<h1>ASO-DB-Standard_Product_information_GB_0816.pdf</h1> <p>Product information</p> <p>ASO®-DB-Standard</p> <p>Waterproof tape</p> <p>Technical data: <br />Basis: polyester fabric with a thermoplastic polyvinyl <br />chloride (PVC) elastomer coating <br />Colour: grey <br />Thickness: </p> <p>approx. 0.62–0.80 mm</p> <p>Impermeability to water <br />in accordance with <br />DIN EN 1928: </p> <p>≥ 1.5 bar</p> <p>Bursting pressure max.: </p> <p>approx. 4 bar</p> <p>Temperature resistance: </p> <p>from -22 °C to +60 °C</p> <p>UV resistance in <br />accordance with <br />DIN EN ISO 4892-2: </p> <p>minimum 500 hours</p> <p>Elongation, longitudinal <br />according to DIN 527-3: ≥ 20 % <br />Elongation, transverse <br />according to DIN 527-3: ≥ 80 %</p> <p>STAIRS/CoS/TM</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>08/16</p> <p>Areas of application: <br />• ASO®-DB-Standard is used for the formation of flexible, water <br />impermeable movement joints and connecting joints beneath <br />tiles within e.g. SANIFLEX, AQUAFIN®-1K-flex, AQUAFIN®-2K, <br />AQUAFIN®-2K/M, AQUAFIN®-RS300 and ASOFLEX®-AKB <br />waterproof membranes. <br />• ASO®-DB-Standard is for use in wet duty exposure classes A0, <br />B0 in accordance with the ZDB technical sheet „bonded <br />waterproof membranes“. <br />• ASO®-DB-Standard is easy to use and forms an intimate bond <br />with the above named waterproof systems.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>Packaging: Joint Tape: width 120 mm ± 2 mm with an <br />approx. 70 mm wide elastomeric coating in the <br />centre, 50 m rolls</p> <p>2 05987</p> <p>Product application: <br />ASO®-DB-Standard at the transition between wall and floor as well as <br />interface joints to the prepared area without voids or folds. Butt joints must <br />be overlapped by 5 to 10 cm. Ensure that a sealed connection to the <br />surrounding waterproof membrane is produced.</p> <p>ASO®-DB-Standard</p> <p>Properties: <br />• Elastomeric coating <br />• Water impermeable <br />• Elastic <br />• UV stabilized <br />• Weatherproof <br />• Alkali resistant</p> <p>1. Coat both sides of the joint to be bridged with the waterproof membrane <br />to a width of at least 2 cm wider than the waterproof tape, e.g. with <br />a 4 – 6 mm notched trowel. <br />2. Then thoroughly work the waterproof tape, without voids or folds, into the <br />waterproof membrane using a steel trowel or pressure roller. Ensure that, <br />as far as possible, a full bed and wetting out is achieved. Bonding must <br />be performed in such as way as to exclude the migration of water <br />behind the waterproof tape. <br />3. The waterproof tape is to be worked into movement joints as a loop. <br />4. Overlap butt joints within waterproof tape sections or at interfaces <br />with all waterproof tape pre-formed pieces and corners by a minimum <br />of 5 to 10 cm and bond with the waterproof membrane, without voids or <br />folds. Overcoat with the chosen waterproof membrane. <br />Application: <br />All usual substrates, which are correctly prepared and suitable for use with <br />the installation of waterproof membranes or tiled finishes in the appropriate <br />wet duty classes (ZDB data sheet ‘bonded waterproof membranes’). Fine, <br />non-penetrative cracks on the surface of < 0.1 mm are acceptable.</p> <p>1 Load-bearing substrate</p> <p>2 Cleaning the wall substrate</p> <p>3 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>4 Bonding the ASO®-DB-Standard into the <br />first coat of the waterproofing membrane</p> <p>5 Application of the first coat of <br />waterproofing membrane</p> <p>6 Allow the first coat to dry</p> <p>7 Application of the second coat of <br />waterproofing membrane</p> <p>8 Completed bonded waterproof membrane</p>
