THERMOPAL-Sanierputzsystem_5025_EN_web_(1).pdf
15 页数
5.9 MB
Download
<h1>THERMOPAL-Sanierputzsystem_5025_EN_web_(1).pdf</h1> <p>SCHOMBURG <br />Problems Solved.</p> <p>THERMOPAL® <br />RESTORATION PLASTER <br />SYSTEMS <br />Reliably restore and waterproof <br />damaged masonry work.</p> <p>schomburg.com</p> <p>Contents <br /> <br />01</p> <p>THERMOPAL® RESTORATION PLASTER SYSTEMS</p> <p>4-7</p> <p>01.1</p> <p>Preparation of the substrate</p> <p>8-9</p> <p>01.2</p> <p>The day system</p> <p>10 - 11</p> <p>01.3</p> <p>The flexible system with radon protection</p> <p>12 - 13</p> <p>01.4</p> <p>The classic system</p> <p>14 - 15</p> <p>02</p> <p>THE RESTORATION SYSTEM WITH INSULATING EFFECT</p> <p>16 - 19</p> <p>02.1</p> <p>For areas affected by damp</p> <p>20 - 21</p> <p>02.2</p> <p>Without additional waterproofing measures</p> <p>22 - 23</p> <p>03</p> <p>APPLICATION TIPS FOR BASEMENT RESTORATION</p> <p>25 - 27</p> <p>Restore masonry work damaged by damp and salt <br />with the THERMOPAL® restoration plaster</p> <p>RETROACTIVE <br />INDOOR RESTORATION</p> <p>THERMOPAL®-SR24</p> <p>THERMOPAL®-ULTRA</p> <p>TOP</p> <p>TEC</p> <p>THERMOPAL®-ULTRA-white</p> <p>INSIDE</p> <p>Retroactive waterproofing building components in direct ground from <br />inside the room is a particular challenge in the building restoration industry. In many cases, the actual cause of damage cannot be rectified from <br />the outside completely due to unfavourable conditions such as adjacent <br />buildings. Subsequent restoration and waterproofing from the inside is <br />often the only solution. <br />Effects of damp and salt damage <br />•D <br /> amage to the building structure (plaster, masonry work) <br />• Loss of living space (rooms are not completely usable) <br />• Loss of energy (high heating costs) <br />• Health hazards (mould formation, allergies)</p> <p>The solution with the THERMOPAL restoration plaster system <br />• Basement wall restoration possible in one day <br />• Radon protection <br />• Function confirmed independently</p> <p>4</p> <p>For predictable working progress <br />thanks to reactive material <br />setting.</p> <p>For rapid restoration work <br />with the best surface <br />quality.</p> <p>Areas of application <br />· Converting living and basement spaces <br />· Restoring usable areas <br />· Salt-loaded surfaces <br />· Damaging plaster surfaces due to <br />hygroscopic damp <br />· Interior and exterior areas</p> <p>Areas of application <br />· Restoring usable spaces <br />· Private and commercial areas <br />· High salt load in the masonry work <br />· Damp damage due to condensation <br />· For building sites under time pressure <br />· Base areas <br />· Interior and exterior areas</p> <p>Areas of application <br />· Restoring living spaces <br />· Private areas <br />· High quality usable areas <br />· Directly usable surfaces <br />· High salt load in the masonry work <br />· Damp damage due to condensation <br />· For building sites under time pressure <br />· Base areas <br />· Interior and exterior areas</p> <p>Properties <br />· High volume of entrained air <br />· Sulphate resistant <br />· Up to 30 mm in one application step <br />· Rapid, reactive bonding behaviour <br />· Vapour permeable <br />· Extremely low shrinkage</p> <p>i <br />In unfavorable conditions, <br />interior renovation is often the only solution.</p> <p>TEC</p> <p>INSIDE</p> <p>Restore damp and salt <br />loaded surfaces economically <br />and safely.</p> <p>Properties <br />· Manual and mechanical application <br />· High salt storage capacity <br />· Vapour permeable <br />· High area coverage</p> <p>TOP</p> <p>Properties <br />· White restoration plaster surface <br />· Climate-regulating <br />· Low material rate <br />· High volume of entrained air <br />· Sulphate resistant <br />· Rapid, reactive bonding behaviour <br />· Vapour permeable <br />· Keeps the surface dry <br />· Extremely low shrinkage</p> <p>5</p> <p>| THERMOPAL® -plaster systems</p> <p>Added safety – <br />additional measures for incorrect <br />and faulty exterior waterproofing <br />Restoration plaster may not be subjected to hydrostatic pressure (pressure water and backwater). <br />They are used in interior areas or in exterior areas <br />if necessary but then only above ground level. <br />If the masonry work is damp due to missing waterproofing measures, it first requires suitable waterproofing measures.</p> <p>System <br />System 1: <br />The day system</p> <p>System 2: <br />The flexible system with radon <br />protection</p> <p>System 3: <br />The classic system</p> <p>Interior waterproofing with a system</p> <p>Interior waterproofing is used if exterior <br />waterproofing is inaccessible, e.g. due to extensions, <br />cannot be performed due to building instability or is <br />not economically viable. Our interior systems <br />provide the optimum solution for waterproofing <br />building components in direct ground safely and <br />permanently.</p> <p>Application areas</p> <p>Advantages</p> <p>• Private areas <br />• High quality usable areas <br />• Underground apartments <br />• Heated basement rooms <br />• Shops <br />• F or non pressure and pressure water</p> <p>• Rapid completion thanks to few steps <br />• Levelling and waterproofing in one <br />application step <br />• White restoration plaster surface</p> <p>• Heated basement rooms <br />• Cracked masonry work <br />• High quality usable areas <br />• Private areas <br />• For normal to high damp load</p> <p>• Rapid, reactive hardening <br />• Radon-tight <br />• Crack bridging</p> <p>• System for usable spaces <br />• Conversion <br />• Storage rooms <br />• Garages <br />• Workshops <br />• For non pressure and pressure water</p> <p>• Manual and mechanical application <br />• High area coverage <br />• Economical</p> <p>TOP</p> <p>Restore faster with <br />TopTec technology <br />Our restoration plasters with the special TopTec <br />technology promise rapid working progress thanks <br />to controlled and reactive bonding behaviour. <br />Benefits include a fast application in the event of <br />unfavourable ambient conditions such as low <br />temperatures and high humidity. Rapid setting is <br />even guaranteed in the event of changing substrate</p> <p>Work day 1 <br />Restoration <br />plaster</p> <p>AQUAFIN-i380</p> <p>THERMOPALULTRA-white</p> <p>ASOCRET-M30</p> <p>INSIDE</p> <p>conditions with different absorption behaviour. <br />The TopTec technology enables restoration measures to be reduced significantly and to be completed on one day thanks to predetermined system <br />components. <br />The table below specifies the work measures for the <br />individual work steps per working day.</p> <p>Work day 2</p> <p>Horizontal barrier Barrier plaster <br />layer</p> <p>TEC</p> <p>Work day 3</p> <p>Work day 4</p> <p>Horizontal barrier Pre-waterproofing / barrier <br />plaster layer</p> <p>Flexible interior waterproofing + <br />splatterdash coat</p> <p>Restoration plaster</p> <p>AQUAFIN-i380</p> <p>AQUAFIN-RB400 + THERMOPAL-SP</p> <p>THERMOPAL-ULTRA</p> <p>First <br />waterproofing <br />layer</p> <p>Second <br />waterproofing <br />layer</p> <p>Third <br />waterproofing layer* <br />+ splatterdash coat</p> <p>Restoration plaster</p> <p>Fine plaster <br />(optional)</p> <p>ASOCRET-M30 AQUAFIN-1K</p> <p>AQUAFIN-1K</p> <p>AQUAFIN-1K + <br />THERMOPAL-SP</p> <p>THERMOPAL-SR24</p> <p>THERMOPAL-FS33</p> <p>ASOCRET-M30</p> <p>Horizontal barrier Seal joints <br />and voids</p> <p>AQUAFIN-F</p> <p>*Optional in the event of pressure water. <br />The time required depends on the ambient conditions and can vary significantly; consider drying times if necessary. Example for a roughly 10 m² <br />surface area without substrate preparation measures.</p> <p>6</p> <p>7</p> <p>Basic renovation plaster system <br />Restoration plaster system for masonry work damaged by <br />damp and salt without additional waterproofing measures</p> <p>THE PREPARATION <br />OF THE SUBSTRATE <br />Basis for sustainable renovation <br />Even the best building products must harmonise with the substrate on <br />which they are used. Ensuring optimum bonding and long-term function <br />requires thorough and meticulous preparation on the building surface to <br />be treated. <br />Measures according to degree of salinisation</p> <p>Expert advice <br />In comparison to conventional plasters such as lime or <br />cement plasters, the THERMOPAL restoration plasters <br />have the benefit of not getting damaged by harmful <br />salts in the substrate and not pressed by the wall. <br />They store the salts in their pore structure and efflorescence is prevented. Water vapour can continue to <br />escape unhindered over the entire plaster structure <br />without causing damage. Masonry work drying is <br />therefore supported.</p> <p>Degree of <br />salinisation</p> <p>Measures</p> <p>Layer thickness in mm</p> <p>Low</p> <p>1. Splatterdash coat <br />2. WTA restoration plaster</p> <p>≤5 <br />≥ 20</p> <p>Medium <br />or high</p> <p>1. Splatterdash coat <br />2. WTA restoration plaster <br />3. WTA restoration plaster</p> <p>≤5 <br />10 – 20 <br />10 – 20</p> <p>High</p> <p>1. Splatterdash coat <br />2. WTA entrained backing <br />coat plaster <br />3. WTA restoration plaster</p> <p>≤5 <br />≥10 <br />≥15</p> <p>ESCO-FLUAT <br />AQUAFIN-i380</p> <p>1. <br /> <br /> <br /> </p> <p>THERMOPAL-ULTRA-white <br />THERMOPAL-SP</p> <p> </p> <p>Subsurface preparation <br />1. R emove the plaster from at least 80 cm beyond the damaged area. <br />2. S <br /> crape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. U <br /> se ESCO-FLUAT to convert sulphate and chloride salts from salts that dissolve <br />easily to salts that are difficult to dissolve. <br />4. U <br /> se THERMOPAL-GP11 to compensate for joints and voids.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier <br />1. U <br /> se AQUAFIN-i380 or AQUAFIN-F to create a retroactive horizontal barrier. <br />2. U <br /> se ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> </p> <p>Restoration plaster system <br />1. F or improved adhesion, apply the THERMOPAL-SP splatterdash coat <br />as a semi-covering to the load-bearing substrate. <br />2. If required (e.g. high salt loading and large surface irregularities), apply <br />the THERMOPAL-GP11 base plaster as an intermediate layer. Roughen <br />up the surface horizontally for the subsequent restoration plaster. <br />3. U <br /> se the THERMOPAL-ULTRA-white restoration plaster to plaster the wall <br />surfaces. <br />4. T HERMOPAL-FS33 can be applied as a finish if fine plaster is required.</p> <p> <br /> <br /> </p> <p>Source: WTA datasheet 2–9 (restoration plaster systems)</p> <p>8</p> <p>9</p> <p>| THERMOPAL® -plaster systems | The day system</p> <p>Products</p> <p>The day system</p> <p>THERMOPAL®-ULTRA-white</p> <p>WTA rapid-setting restoration plaster <br />• White restoration plaster surface, usable directly <br />• Climate-regulating <br />• High yield <br />• Reactive full curing in the event of critical site conditions</p> <p>For fast restoration work <br />in one day</p> <p>AQUAFIN®-i380</p> <p>Injection cream for the retroactive horizontal barrier <br />to prevent capillary rising damp <br />• Ready to use <br />• High penetration depth <br />• Easy and safe to use <br />• Application without any pressure</p> <p>ASOCRET-M30</p> <p>Water-repellent multi-mortar up to 30 mm for levelling <br />and interior wall waterproofing <br />• Rapid setting <br />• Sulphate resistant <br />• Very smooth application</p> <p>ASOCRET-M30 <br />AQUAFIN-Primer <br />AQUAFIN-i380</p> <p>1. <br /> <br /> <br /> </p> <p>THERMOPAL-ULTRA-white</p> <p> </p> <p>Subsurface preparation <br />1. Remove the plaster from at least 80 cm beyond the damaged area. <br />2. Scrape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. Use ESCO-FLUAT to convert sulphate and chloride salts from salts that dissolve <br />easily to salts that are difficult to dissolve. <br />4. Use ASOCRET-M30 to compensate for joints and voids. <br />5. Use ASOCRET-M30 to insulate the existing horizontal barrier and locking <br />groove in the wall-floor transition. <br />6. Use ASOCRET-M30 to implement a sealing groove in the floor-wall transition.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier <br />1. Use AQUAFIN-i380 to create a retroactive horizontal barrier. <br />2. Use ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> <br /> </p> <p>Interior waterproofing <br />1. Apply ASOCRET-M30 as a barrier plaster layer and for surface levelling. <br />2. Comb the layer that is still fresh horizontally using an 6 mm notched trowel.</p> <p>4. <br /> </p> <p>Restoration plaster system <br />1. Use the THERMOPAL-ULTRA-white restoration plaster to plaster the wall <br />surfaces.</p> <p> <br /> </p> <p>10</p> <p>ESCO-FLUAT</p> <p>Solution for treating structurally damaging salts <br />• Concentrate <br />• To covert structurally damaging salts <br />• To prevent too early a salt effect in fresh restoration plaster <br />• Solvent-free</p> <p>i <br />Further information to the products <br />can be found online.</p> <p>11</p> <p>| THERMOPAL® -plaster systems | The flexible system with radon protection</p> <p>Products</p> <p>The flexible system with radon protection <br />Restoration system with high requirements for crack <br />bridging and with reliable protection from radon loading</p> <p>THERMOPAL®-ULTRA</p> <p>WTA rapid-setting restoration plaster <br />• Rapid, reactive hardening <br />• High volume of entrained air <br />• Up to 30 mm in one application step <br />• Sulphate resistant</p> <p>THERMOPAL®-FS33</p> <p>Fine mortar for THERMOPAL restoration plasters <br />• Cementitious fine plaster <br />• Vapour permeable <br />• Low-stress <br />• For interior and exterior use</p> <p>AQUAFIN®-RB400</p> <p>THERMOPAL-ULTRA <br />THERMOPAL-SP <br />AQUAFIN-RB400 <br />ASOCRET-M30 <br />ESCO-FLUAT <br />AQUAFIN-i380</p> <p>1. <br /> <br /> <br /> </p> <p> </p> <p>Subsurface preparation <br />1. Remove the plaster from at least 80 cm beyond the damaged area. <br />2. Scrape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. Use ESCO-FLUAT to convert sulphate and chloride salts from salts that dissolve <br />easily to salts that are difficult to dissolve. <br />4. Use ASOCRET-M30 to compensate for joints and voids. <br />5. Use ASOCRET-M30 to insulate the existing horizontal barrier and locking <br />groove in the wall-floor transition. <br />6. Use ASOCRET-M30 to implement a sealing groove in the floor-wall transition.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier <br />1. Use AQUAFIN-i380 to create a retroactive horizontal barrier. <br />2. Use ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> <br /> </p> <p>Flexible interior waterproofing <br />1. Apply ASOCRET-M30 as a barrier plaster layer and for surface levelling. <br />2. Apply AQUAFIN-RB400 as flexible interior waterproofing.</p> <p>4. <br /> </p> <p>Restoration plaster system <br />1. For improved adhesion, apply the THERMOPAL-SP splatterdash coat over <br />the complete area. <br />2. Use the THERMOPAL-ULTRA restoration plaster to plaster the wall surfaces. <br />3. THERMOPAL-FS33 can be applied as a finish if fine plaster is required.</p> <p> <br /> </p> <p> <br /> </p> <p>12</p> <p>Rapid cementitious waterproofing for substrates <br />at risk of cracking with radon protection <br />• Rapid, reactive drying <br />• Crack bridging <br />• Vapour permeable <br />• Radon-tight</p> <p>AQUAFIN®-i380</p> <p>Injection cream for the retroactive horizontal <br />barrier to prevent capillary rising damp <br />• Ready to use <br />• High penetration depth <br />• Easy and safe to use <br />• Application without any pressure</p> <p>ASOCRET-M30</p> <p>Water-repellent multi-mortar up to 30 mm for levelling <br />and interior wall waterproofing <br />• Rapid setting <br />• Sulphate resistant <br />• Very smooth application</p> <p>Further system products: <br />• THERMOPAL-SP WTA preparatory renovating sprayed mortar <br />• THERMOPAL-GP11 WTA base plaster <br />• ESCO-FLUAT Solution for treating structurally damaging salts</p> <p>13</p> <p>| THERMOPAL® -plaster systems | The classic system</p> <p>Products</p> <p>The classic system <br />Retroactive basement restoration with cementitious waterproofing slurry for substrates that are not a risk of cracking</p> <p>THERMOPAL®-SR24</p> <p>WTA restoration plaster with high air pore content <br />• Manual and mechanical application <br />• High salt storage capacity <br />• Vapour permeable, supports drying <br />• Wide range, high area coverage</p> <p>THERMOPAL®-FS33</p> <p>Fine mortar for THERMOPAL restoration plasters <br />• Cementitious fine plaster <br />• Vapour permeable <br />• Low-stress <br />• For interior and exterior use</p> <p>AQUAFIN®-1K</p> <p>Mineral waterproofing slurries for retroactive waterproofing <br />of substrates that are not at risk of cracking <br />• Sulphate resistant <br />• Water tight <br />• Easy, economic application <br />• Adheres to matt damp substrates without primers <br />THERMOPAL-SR24 <br />THERMOPAL-SP <br />AQUAFIN-1K <br />ASOCRET-M30 <br />ESCO-FLUAT <br />AQUAFIN-F</p> <p>1. <br /> <br /> <br /> </p> <p> </p> <p>Subsurface preparation <br />1. Remove the plaster from at least 80 cm beyond the damaged area. <br />2. Scrape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. Use ESCO-FLUAT to convert sulphate and chloride salts from salts that dissolve <br />easily to salts that are difficult to dissolve. <br />4. Use ASOCRET-M30 to compensate for joints and voids. <br />5. Use ASOCRET-M30 to insulate the existing horizontal barrier and locking <br />groove in the wall-floor transition. <br />6. Use ASOCRET-M30 to implement a sealing groove in the floor-wall transition.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier <br />1. Use AQUAFIN-F to create a retroactive horizontal barrier. <br />2. Use ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> </p> <p>Interior waterproofing <br />1. Apply AQUAFIN-1K as retroactive interior waterproofing with cementitious <br />waterproofing slurry. Three layers in the event of pressure water.</p> <p>4. <br /> </p> <p>Restoration plaster system <br />1. For improved adhesion, apply the THERMOPAL-SP splatterdash coat over <br />the complete area. <br />2. Use the THERMOPAL-SR24 restoration plaster to plaster the wall surfaces. <br />3. THERMOPAL-FS33 can be applied as a finish if fine plaster is required.</p> <p> <br /> </p> <p> <br /> </p> <p>14</p> <p>AQUAFIN®-F</p> <p>To create retroactive horizontal barriers if damp <br />increases in the walls <br />• Ready to use <br />• Up to 95 % moisture penetration in the pressure process <br />• Vapour permeable <br />• Solvent-free</p> <p>ASOCRET-M30</p> <p>Water-repellent multi-mortar up to 30 mm for levelling <br />and interior wall waterproofing <br />• Rapid setting <br />• Sulphate resistant <br />• Very smooth application</p> <p>Further system products: <br />• THERMOPAL-SP WTA preparatory renovating sprayed mortar <br />• THERMOPAL-GP11 WTA base plaster <br />• ESCO-FLUAT Solution for treating structurally damaging salts</p> <p>15</p> <p>| The restoration system with insulating effect</p> <p>THE RESTORATION SYSTEM <br />WITH INSULATING EFFECT <br />Thermal insulation plaster in combination with interior sealing</p> <p>For damp wall areas or inefficient <br />walls in energy terms <br />i <br />Thermal insulation and moisture <br />regulation in one solution: safe, <br />vapour-permeable, sustainable.</p> <p>16</p> <p>Application areas: <br />• restoration of living spaces <br />• increasing energy efficiency of old buildings <br />• listed buildings <br />• mould treatment / moisture damage <br />• private and high quality utility areas <br />• use with wall heating systems <br />• existing buildings, basements, pedestal areas</p> <p>Moisture, mould growth, inadequate thermal insulation are <br />typical challenges when renovating interiors in existing buildings <br />or listed/historical buildings. Conventional systems quickly reach <br />their limits. Either the insulation value is insufficient, or there is no <br />adequate waterproofing against rising or laterally penetrating <br />moisture. <br />The combination of cementitious interior waterproofing made <br />of ASOCRET-M30 and the thermal insulation plaster <br />THERMOPAL-WSP-120 offers a reliable and vapour-permeable <br />solution for precisely this problem.</p> <p>THERMOPAL-WSP-120: <br />Insulating plaster with climate regulation <br />The mineral thermal insulation and restoration plaster <br />THERMOPAL-WSP-120 are applied directly to the interior <br />waterproofing. It not only offers a noticeable improvement in <br />surface temperature and thus living comfort, but also has a <br />climate-regulating effect: excess moisture from the room air is <br />absorbed and released again, thereby consistently reducing the <br />risk of mould formation. <br />If a salt-storing intermediate layer is required due to high salt <br />concentrations in the masonry work, our WTA renovation quicksetting plaster offers the necessary pore space to safely store salts.</p> <p>17</p> <p>| The restoration system with insulating effect</p> <p>RESTORATION AND <br />IMPROVED ENERGY EFFICIENCY <br />THERMOPAL®-WSP-120</p> <p>Climate-regulating. <br />Thermal insulation. <br />Vapour permeable.</p> <p>cementitious heat insulation and restoration plaster <br />for interior restoration with insulating effect.</p> <p>THERMOPAL-WSP-120 offers a powerful solution for the <br />energy-efficient renovation of existing buildings, while <br />simultaneously protecting against moisture and mould growth.</p> <p>The advantages <br />Climate-regulating</p> <p>The purely cementitious thermal insulation and restoration plaster <br />combines excellent insulation performance with natural regulation <br />of the room climate, ideal for use in living spaces, old buildings, <br />listed buildings or high-quality usable areas in the basement.</p> <p>Thermal insulation</p> <p>Due to its vapour permeable structure, THERMOPAL-WSP-120 <br />actively supports moisture exchange and thus prevents <br />condensation and mould growth.</p> <p>Vapour permeable <br />Water inhibiting</p> <p>THERMOPAL®-WSP-120 <br />Cementitious heat insulation and restoration plaster <br />• moisture regulating <br />• cementitious thermal insulation plaster <br />• thermal insulating properties <br />• non-combustible <br />• for layer thicknesses up to 120 mm <br />• machine-accessible</p> <p>i <br />The lower the U-value, the better <br />the thermal insulation properties.</p> <p>Compared to an uninsulated masonry work made of solid bricks, <br />the heat transfer coefficient (U-value) is improved by up to 200%.</p> <p>The positive effect of THERMOPAL-WSP-120 compared <br />to uninsulated masonry work.</p> <p>U-values in comparison</p> <p>Initial value: Masonry work against earth, plastered <br />without thermal insulation measures</p> <p>Solid brick masonry work <br />with 100 mm <br />THERMOPAL-WSP-120 <br />Uninsulated solid brick <br />masonry work <br />0</p> <p>0.5</p> <p>1</p> <p>1.5</p> <p>2</p> <p>Masonry work</p> <p>Wall <br />Heat <br />conductivity thickness <br />in mm <br />coeff.</p> <p>U-value <br />W/(m²·K)</p> <p>Solid brick</p> <p>0.81</p> <p>365</p> <p>1.51</p> <p>Lime sandstone</p> <p>0.99</p> <p>365</p> <p>1.54</p> <p>Concrete</p> <p>1.35</p> <p>365</p> <p>1.82</p> <p>Pumice hollow blocks</p> <p>0.46</p> <p>365</p> <p>0.93</p> <p>U-value with THERMOPAL-WSP-120 depending <br />on the plaster thickness in mm <br />40 mm</p> <p>60 mm</p> <p>80 mm</p> <p>100 mm 120 mm</p> <p>0.81</p> <p>0.66</p> <p>0.55</p> <p>0.48</p> <p>0.42</p> <p>0.82</p> <p>0.66</p> <p>0.56</p> <p>0.48</p> <p>0.42</p> <p>0.89</p> <p>0.71</p> <p>0.59</p> <p>0.51</p> <p>0.44</p> <p>0.61</p> <p>0.52</p> <p>0.45</p> <p>0.40</p> <p>0.36</p> <p>Measured values are <br /> guideline values after DIN 4108-4. Object-specific calculations are necessary for an accurate assessment.</p> <p>18</p> <p>19</p> <p>| The restoration system with insulating effect | For areas exposed to damp</p> <p>The restoration system <br />with insulating effect <br />For areas affected by damp</p> <p>Products <br />THERMOPAL®-WSP-120</p> <p>Cementitious thermal insulation and restoration plaster <br />• thermal insulating properties <br />• humidity regulating <br />• for layer thicknesses up to 120 mm <br />• machine-accessible</p> <p>ASOCRET-M30</p> <p>Water-repellent multi-mortar up to 30 mm for levelling <br />and interior wall waterproofing <br />• rapid setting <br />• sulphate resistant <br />• very smooth application</p> <p>AQUAFIN®-i380</p> <p>Injection cream for the retroactive horizontal barrier <br />to prevent capillary rising damp <br />• ready to use <br />• high penetration depth <br />• simple and reliable application <br />• pressure-free application</p> <p>THERMOPAL®-FS33</p> <p>1. <br /> <br /> <br /> <br /> <br /> <br /> </p> <p>Substrate preparation <br />1. Remove the plaster from at least 80 cm beyond the damaged area. <br />2. Scrape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. Pretreat damp masonry work with AQUAFIN-Primer. <br />4. Use ASOCRET-M30 to compensate for joints and voids. <br />5. Use ASOCRET-M30 to insulate the existing horizontal barrier and locking groove in the wall-floor transition. <br />6. Create cementitious fillet at floor/wall transition with ASOCRET-M30.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier <br />1. Use AQUAFIN-i380 to create a retroactive horizontal barrier. <br />2. Use ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> <br /> </p> <p>Interior waterproofing <br />1. Apply ASOCRET-M30 as a barrier plaster layer and for surface levelling. <br />2. Comb the layer that is still fresh horizontally using an 6 mm notched trowel.</p> <p>4. <br /> <br /> </p> <p>Salt trap as an intermediate layer if needed <br />1. Apply the plaster coat with THERMOPAL-ULTRA-white in a layer thickness of approximately 15 mm. <br />2. Comb the layer that is still fresh horizontally using an 6 mm notched trowel.</p> <p>5. <br /> <br /> <br /> </p> <p>Thermal insulation plaster <br />1. Plaster the wall surfaces with THERMOPAL-WSP-120 <br />2. After drying, prime the plaster surface with AQUAFIN primer. <br />3. Then, rework the plaster surface with the THERMOPAL-FS33 fine filler in two application steps.</p> <p>20</p> <p>Fine mortar for THERMOPAL restoration plasters <br />• cementitious fine plaster <br />• vapour permeable <br />• low stress <br />• for interior and exterior use</p> <p>AQUAFIN-Primer</p> <p>Dependable primer for building waterproofing and renovation <br />• dispersion silicate primer with improved adhesion properties <br />• ready to use <br />• rapid drying <br />• substrate consolidating</p> <p>Further system products: <br />• THERMOPAL-SP WTA preparatory renovating sprayed mortar <br />• THERMOPAL-GP11 WTA base plaster <br />• ESCO-FLUAT Solution for treating structurally damaging salts</p> <p>21</p> <p>| The restoration system with insulating effect | Without additional measures</p> <p>The system for sustainable <br />building restoration</p> <p>Without additional waterproofing measures</p> <p>Products <br />THERMOPAL®-WSP-120</p> <p>Cementitious thermal insulation and restoration plaster <br />• thermal insulating properties <br />• humidity regulating <br />• for layer thicknesses up to 120 mm <br />• machine-accessible</p> <p>THERMOPAL®-FS33</p> <p>NEW</p> <p>Fine mortar for THERMOPAL restoration plasters <br />• cementitious fine plaster <br />• vapour permeable <br />• low stress <br />• for interior and exterior use</p> <p>AQUAFIN®-i380</p> <p>Injection cream for the retroactive horizontal barrier <br />to prevent capillary rising damp <br />• ready to use <br />• high penetration depth <br />• simple and reliable application <br />• pressure-free application</p> <p>AQUAFIN-Primer</p> <p>1. <br /> <br /> <br /> <br /> </p> <p>Substrate preparation <br />1. Totally remove the old plaster. <br />2. Scrape crumbly and salt loaded joints out to at least 20 mm deep. <br />3. Prime highly absorbent masonry work with AQUAFIN-Primer. <br />4. Use THERMOPAL-GP11 to compensate for joints and voids.</p> <p>2. <br /> <br /> </p> <p>Horizontal barrier if required <br />1. Use AQUAFIN-i380 or AQUAFIN-F to create a retroactive horizontal barrier. <br />2. Use ASOCRET-M30 to seal the drilled holes again.</p> <p>3. <br /> <br /> <br /> <br /> </p> <p>Thermal insulation plaster <br />1. For improved adhesion, apply the THERMOPAL-SP splatterdash coat as a semi-covering to the load-bearing substrate. <br />2. Plaster the wall surfaces with THERMOPAL-WSP-120. <br />3. After drying, prime the plaster surface with AQUAFIN primer. <br />4. Then, rework the surface with the THERMOPAL-FS33 fine filler in two application steps.</p> <p>22</p> <p>Dependable primer for building waterproofing and renovation <br />• dispersion silicate primer with improved adhesion properties <br />• ready to use <br />• rapid drying <br />• substrate consolidating</p> <p>ASOCRET-M30</p> <p>Water-repellent multi-mortar up to 30 mm for levelling <br />and interior wall waterproofing <br />• rapid setting <br />• sulphate resistant <br />• very smooth application</p> <p>Further system products: <br />• THERMOPAL-SP WTA preparatory renovating sprayed mortar <br />• THERMOPAL-GP11 WTA base plaster <br />• ESCO-FLUAT Solution for treating structurally damaging salts</p> <p>23</p> <p>| Application tips for basement restoration</p> <p>Application tips for <br />basement restoration <br />1.</p> <p>For retrospective horizontal barriers <br />Injection cream AQUAFIN-i380 <br />AQUAFIN-i380 is a silane-based injection cream for the <br />creation of retrospective horizontal barriers, which is applied <br />without any pressure and has a hydrophobic action against <br />rising damp in masonry work. The material has been tested <br />and certified in accordance with WTA data sheet 4-10 at a <br />penetrating moisture level of 95%.</p> <p>T HE BUILDING COMPONENT STATUS <br />ANALYSIS</p> <p>Every waterproofing project requires a preliminary investigation <br />and a plan based on that investigation. The following points <br />regarding the condition of the building structure must be <br />surveyed and documented: <br />• Survey, salt analysis: <br /> What damage is there? <br />• Effects, special features: e.g. capillary rising damp, <br />saturation from rear, condensation, accident damage, <br />settlement, etc.</p> <p>The fine active ingredient only reacts with the substrate – not <br />with water – and spreads quickly in the masonry work. As a <br />result, the pores are totally saturated, the capillary walls become <br />water-repellent, water transport is stopped and the substrate <br />dries out.</p> <p>1.</p> <p>2. SUBSTRATE PREPARATION <br />Damaged wall surfaces must be completely stripped of plaster. <br />For partial restorations (e.g. in the plinth area transition), remove <br />and clean the plaster up to 80 cm above the damage limit. <br />• Chase out masonry joints to approx. 20 mm <br />• Create load-bearing substrate</p> <p>3. HORIZONTAL BARRIER <br />A horizontal barrier is required to prevent capillary water <br />transport. <br />• Unpressurised injection with AQUAFIN-i380 <br />• Use ASOCRET-M30 to reseal the drilled holes at surface</p> <p>2. <br />3.</p> <p>3.</p> <p>AQUAFIN®-i380 <br />Injection cream for the retroactive <br />horizontal barrier to prevent <br />capillary rising damp <br />• ready to use <br />• high penetration depth <br />• simple and reliable application <br />• pressure-free application</p> <p>24</p> <p>25</p> <p>| Application tips for basement restoration</p> <p>Application tips for <br />basement restoration</p> <p>Always on the right side <br />With the versatile multimortar ASOCRET-M30 <br />4.</p> <p>4. TRANSITION AT FLOOR/WALL JUNCTION <br /> <br />A fillet is formed using the ASOCRET-M30 sealing mortar in the <br />transition between the wall and floor. <br />• Cut back existing horizontal barrier <br />• Chase out a groove in the floor-wall transition</p> <p>5.</p> <p>The use of suitable waterproofing systems is particularly <br />crucial for the interior renovation of damp and salt loaded <br />wall surfaces – such as for the retrospective waterproofing of <br />building components in contact with the ground. In accordance <br />with the WTA leaflet 4-6 “Retrospective waterproofing of <br />building components in contact with the ground”, this also <br />includes a high-performance sealing mortar for the preparation <br />and implementation of sealing measures. With the watertight <br />multi-mortar ASOCRET-M30 you are on the safe side for</p> <p>every application: Whether as a barrier plaster, reprofiling mortar, <br />bonding slurry, sealing fillet mortar or for creating suitable substrates <br />for retrospective renovation plaster systems – ASOCRET-M30 meets <br />all requirements and is ideally suited for waterproofing building <br />components in contact with the ground. Reactive drying for rapid <br />construction progress even under challenging weather conditions. <br />ASOCRET-M30 is a genuine all-rounder for daily use on the <br />building site.</p> <p>PREPARATION FOR PRE-SPRAY MORTAR <br />To create secure bonding, pre-spray mortar is applied. <br />• Direct onto the masonry work: in net pattern, ≤ 50% cover <br />• With waterproofing slurries: covering whole area, <br />100% cover</p> <p>6. PREPARE ASOCRET-M30 FOR SUBSEQUENT</p> <p>5.</p> <p>RESTORATION PLASTER</p> <p>Surface levelling and waterproofing with the water-repellent <br />multi-mortar ASOCRET-M30. <br />• Apply a 20 mm thick layer of waterproof plaster <br />• Rake the fresh layer horizontally with 6 mm notched trowel</p> <p>7.</p> <p> OST-TREATMENT OF RESTORATION <br />P <br />PLASTERS <br />After sufficient standing time, felt or rub the surface until it is matt <br />damp. <br />• Premature, wet rubbing can cause stress cracks <br />• Alternative: grid float for removing the laitance layer and <br />optimising drying</p> <p>4.</p> <p>6.</p> <p>7.</p> <p>26</p> <p>ASOCRET-M30 <br />Water impermeable <br />multimortar up to 30 mm <br />• Suitable as building skirt render <br />• Waterproof fillet mortar in accordance with DIN 18533 <br />• High slump resistance <br />• Rapid setting <br />• Sulphate resistant <br />• Hydrophobic</p> <p>27</p> <p>The SCHOMBURG Group develops, produces <br />and distributes building product systems for the <br />areas of:</p> <p>To meet the demanding requirements of an <br />ever-changing market, we continuously invest in <br />the research and development of new and <br />already existing products. This guarantees an <br />ever increasing product quality to the satisfaction <br />of our customers.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>06/26 T50/25 NT/IsW/KKa</p> <p>Experts value the quality and the efficiency of <br />building product systems, the services and <br />therefore the core competence of the group of <br />companies.</p> <p>2D1023000</p> <p>For over 85 years SCHOMBURG’s <br />development competence has been recognised <br />in both the domestic and the worldwide <br />marketplace. Building product systems that are <br />produced in-house are highly prized around the <br />world.</p> <p>Subject to change without prior notification. The valid issue of the corresponding technical bulletin legally applies.06</p> <p>• Waterproofing and repair of buildings <br />• Tiles/natural stone/screed application <br />• Ground protection/floor coating systems</p>
