ASOCRET-BIS-16_206437_Englisch.pdf
4 页数
1.2 MB
Download
<h1>ASOCRET-BIS-16_206437_Englisch.pdf</h1> <p>Technical data sheet <br />ASOCRET-BIS-1/6 <br />Cementitious fine smoothing mortar for breakage points of 1–6 mm</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>206437001</p> <p>25 kg, bag</p> <p>Cement grey</p> <p>42</p> <p>1</p> <p>Areas of application <br />As a non slump re-profiling mortar <br />For levelling pool tank walls, as well as modelling pool edges in swimming pools <br />For concrete repair <br />For breakout depths ca. 1 - 6 mm <br />For walls, ceilings, floors</p> <p>Advantages <br />watertight <br />Vapour permeable <br />Frost proof and resistant to thaw <br />Can be trowelled and sprayed <br />High resistance to carbonation</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/4</p> <p>16/01/2026</p> <p>Technical data sheet <br />ASOCRET-BIS-1/6 <br />Product features <br />Plastic-modified fine cement-based mortar (PCC) <br />CE after DIN EN 1504-03 <br />Chloride-free <br />Largest grain size: ≤ 1 mm</p> <p>Technical Data <br />Material properties <br />Product components <br />Base material <br />Consistency <br />Grain size max <br />Bulk density of fresh mortar <br />Compressive strength (24 hrs.) <br />Compressive strength (7 days) <br />Compressive strength (28 days) <br />Flexural strength (24 hrs.) <br />Flexural strength (7 days) <br />Flexural strength (28 days) <br />Tensile adhesion strength DIN EN 1542 <br />Curve E module (DIN 53452) <br />Chloride content <br />Classification of the reaction to fire in accordance with DIN EN 13501-1</p> <p>1 component system <br />Pre-blended dry mortar <br />Filler consistency <br />< 0.5 mm <br />approx. 2.1 kg/dm³ <br />approx. 11 N/mm² <br />approx. 30 N/mm² <br />approx. 40 N/mm² <br />approx. 2 N/mm² <br />approx. 7 N/mm² <br />approx. 8 N/mm² <br />≥ 0.8 N/mm² <br />approx. 20 N/mm² <br />≤ 0.05 % <br />A1</p> <p>Mixing <br />Mixing time <br />Maturing time <br />Water addition</p> <p>approx. 3 minutes <br />approx. 5 minutes <br />From 5 l to 5.25 l per 25 kg</p> <p>Application <br />Substrate/application temperature <br />Pot life <br />Method of application, max. layer thickness per application step <br />Consumption pro m² and mm layer thickness <br />Overcoat after (min.) <br />Foot traffic after</p> <p>approx. 5 - 30 °C <br />approx. 60 minutes <br />up to 6 mm <br />approx. 1.6 kg/m² <br />after 24 hours <br />approx. 24 hours</p> <p>Processing equipment <br />Aids/tools <br />Stirrer (approx. 500-700 rpm) <br />Suitable mixing paddle <br />Trowel <br />Flat trowel <br />Sponge board <br />Spray equipment <br />Plasterer’s darby <br />Construction compressor <br />Forced paddle mixer</p> <p>Machine application <br />ASOCRET-BIS-1/6 can be mechanically applied. For precise information, see the additional Technical Information No. 43.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/4</p> <p>16/01/2026</p> <p>Technical data sheet <br />ASOCRET-BIS-1/6 <br />Suitable substrate <br />Concrete <br />Cement-based screed (CT)</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Firm <br />2. Grippy <br />3. Load-bearing <br />4. Free of adhesion inhibiting substances</p> <p>Preparing the surface <br />Pre-moisten the dry substrate so that it is matt damp at the time of application.</p> <p>Preparing the details <br />1. If no previous concrete restoration work has been carried out, a substrate preparation (e.g. granulate, shot, ultra-high pressure water jetting (5002000 bar)) is required. <br />2. Exposed reinforcing steels must be pretreated with the corrosion protection ASOCRET-HS-FLEX in accordance with the technical data sheet.</p> <p>Application <br />Mixing <br />1. Add water (From 5 l to 5.25 l per 25 kg) to a clean mixing bucket and mix with 25 kg of the powder component to produce a homogeneous, <br />lump-free mass. <br />2. Use a forced paddle mixer for larger coatings. <br />3. After a settling period of ca. 5 minutes, thoroughly homogenise the compound again. <br />4. Use a forced paddle mixer for larger coatings.</p> <p>Application <br />1. On the prepared substrate, apply ASOCRET-BIS-1/6 beforehand with a scratch coat and then in the desired layer thickness. <br />2. Striking off is done with a suitable tool (float, trowel, etc.), depending on the application, within the pot life. <br />3. The surface can be treated using a felt or sponge board after a corresponding waiting time.</p> <p>Curing <br />1. After applying ASOCRET-BIS-1/6, the mortar surfaces must generally be protected from rapid drying using suitable measures. <br />2. To do this, keep the surfaces damp for at least 3-5 days using water mist nozzles, wet jute sheets or even by covering with film. <br />3. The film must be attached to the surfaces to be treated in such a way that an air exchanged is ruled out. <br />4. If the mortar surfaces concerned are exposed to direct sunlight, draughts, high temperature fluctuations and/or low humidity, more attention must <br />be paid to the curing measures. <br />5. If a subsequent waterproofing with cementitious waterproofing slurry is intended, this can be applied as an alternative curing method after <br />approx. 24 hours.</p> <p>Cleaning tools <br />Rinse tools with water immediately after use.</p> <p>Storage conditions <br />Storage <br />Cool, dry, protected from sunlight. Min. 12 months in the original canister. Promptly use opened container.</p> <p>Notes <br />Before any concrete restoration measures, the current state must generally be checked by an expert and/or structural engineer. The test <br />report must be made available to the processor before starting the restoration measures. <br />Protect surfaces that are not to be treated from the effects of ASOCRET-BIS-1/6! <br />Do not add water or new mortar to existing ASOCRET-BIS-1/6 mortar that has already set in order to make it workable again. (Risk of <br />inadequate strength development)</p> <p>Observe applicable safety data sheet!</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/4</p> <p>16/01/2026</p> <p>Technical data sheet <br />ASOCRET-BIS-1/6 <br />Explanations <br />Conformity / Declaration / Verification</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />4/4</p> <p>16/01/2026</p>
