ASO-RSG_205024_Englisch.pdf
3 页数
1.3 MB
Download
<h1>ASO-RSG_205024_Englisch.pdf</h1> <p>Technical data sheet <br />ASO®-RSG <br />Crack prevention fabric to rennovate critical and cracked surfaces</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>205024001</p> <p>30 m², 25mx120cm (LxW), roll</p> <p>grey-white</p> <p>40,000</p> <p>1,000</p> <p>Fields of application / waterproofing <br />for floor renovation <br />for floor renovation with ASODUR®-SG3-thix <br />for sub-surface preparation of wearing surfaces and coverings <br />for cementitious mortar systems <br />For critical substrates in conjunction with ASOCRET-M30 and THERMOPAL® restoration plasters <br />for garages and industrial floors <br />for workshop floors <br />for transitions between building sections <br />For walls and floors <br />for interior and exterior use <br />For waterproofing with AQUAFIN®-RB400 and AQUAFIN®-2K/M-PLUS</p> <p>Product features <br />Crack bridging <br />stabilising <br />high tensile strength <br />Easy application <br />4-D movement accommodation <br />Resistant to alkalis <br />Horizontal, vertical and diagonal force absorption</p> <p>Advantages <br />Low installation height <br />time-saving renovation <br />For substrates with low strength <br />Resistant to negative water pressure up to 17.5 metres water column in the system <br />In accordance with WTA Leaflet 4-6 “Subsequent waterproofing of building components in direct ground contact” <br />With ASODUR-SG3-thix radon tight</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/3</p> <p>26/04/2026</p> <p>Technical data sheet <br />ASO®-RSG <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Surface weight <br />Watertightness against negative pressing water (WTA-datasheet 4-6) <br />Tensile force +45° / -45° <br />Mesh width <br />Tensile elongation behaviour, lengthwise <br />Tensile elongation behaviour, crosswise</p> <p>Roll goods <br />E-glass roving <br />approx. 245 g / m² ± 5% <br />to 1,75 bar <br />approx. 1400 / 1400 N / 50 mm <br />6x6 <br />approx. 1150 N / 50 mm <br />approx. 1450 N / 50 mm</p> <p>Application <br />Consumption</p> <p>approx. 1 m² per m²</p> <p>System components for building waterproofing <br />Primer <br />Waterproofing <br />Mortar / restoration plaster</p> <p>ASODUR-SG3-thix <br />AQUAFIN-RB400 <br />AQUAFIN-2K/M-PLUS <br />ASOCRET-HFF <br />ASOCRET-M30 <br />THERMOPAL restoration plaster</p> <p>Processing equipment <br />Aids/tools <br />Stirrer (approx. 500-700 rpm) <br />Suitable mixing paddle <br />Flat trowel <br />Brush <br />Scissors/knife <br />Rubber lip slider <br />Nylon fur roller (6mm) with textured polyamide cover <br />Surface rake <br />Spiked shoes <br />spiked roller</p> <p>Suitable substrate <br />Concrete <br />Cement-based screed (CT) <br />Masonry work <br />Plasters P II and P III</p> <p>Preparing the substrate <br />Requirement for substrate <br />1. Even <br />2. Free of adhesion inhibiting substances <br />3. Sealed in the surface <br />4. Pore open <br />5. Load-bearing</p> <p>Measures for substrate preparation <br />1. Substrate preparations must be carried out in compliance with DIN EN 14879-1:2005, 4.2 et.seq. <br />2. We recommend preparing the substrate by grinding with a diamond grinder or shot blasting.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/3</p> <p>26/04/2026</p> <p>Technical data sheet <br />ASO®-RSG <br />Application <br />As a reinforcing layer <br />1. Cut ASO®-RSG to the appropriate length. <br />2. Lay the material out and place the fabric without wrinkles into the upper third of the reinforcement layer and rework it. <br />3. When used in renovation plaster systems, the plaster coverage is approx. 5 mm. <br />4. The overlap of individual fabric panels in cementitious mortar systems is 10 cm.</p> <p>Application <br />1. Surface irregularities, holes and damaged areas with ASOCRET-M30 or EP mortar (ASODUR-SG3-thix and quartz sand Ø0.5-1.0 mm in a ratio <br />of 6:25 parts by weight). <br />2. Apply the RD-SK50 self-adhesive edging strips to the wall-floor transition and the rising building components in advance. <br />3. Cut ASO®-RSG to the appropriate length. <br />4. Place fabric strips onto the prepared substrate with the printed side facing up. Maintain a gap of at least 3 cm to rising building components. <br />5. Overlap the ends of the strips by at least 20 mm. <br />6. Coat the surface with ASODUR®-SG3-thix. Apply the coating evenly using a rubber lip squeegee and nylon roller. (Consumption: approx. 0.8 1.0 kg/m²) <br />7. Roll over the surface again and level it. <br />8. Sprinkle the still wet layer evenly with excess fire-dried quartz sand (ø 0.5–1.0 mm). (consumption: 2.0 - 2.5 kg/m²) <br />9. After 12 hours, sweep and vacuum away all excess quartz sand. <br />10. Overcoat the surface with ASOCRET-HFF as a wearing surface (minimum layer thickness: > 5.0 mm) <br />11. For a uniform surface appearance, rework the cured layer of ASOCRET-HFF with ASODUR®-V360W in the desired colour. <br />12. Seal existing expansion and/or connecting joints with INDUFLEX-PU.</p> <p>Storage conditions <br />Storage <br />Cool, dry, protected from sunlight. Min. 24 months in the original canister. <br />Do not store in the open.</p> <p>Notes <br />ASO®-RSG may not be glued or overcoated afterwards with products containing solvents. <br />A joint overlap of more than 20 mm results in increased material consumption. <br />Visible overlap areas have no influence on the functionality of the coating and do not constitute a defect. <br />Expansion joints may not be overcoated. <br />Fill larger cracks in advance to prevent subsequent layers from flowing away. <br />Construction-related cracks with completed deformation must be sealed in advance with a force-fitting reactive resin. Otherwise, provide <br />expansion joints. <br />Observe the technical data sheets of the products mentioned before starting work.</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/3</p> <p>26/04/2026</p>
