AQUAFIN-P4_205221_Englisch.pdf
3 页数
1020.8 KB
Download
<h1>AQUAFIN-P4_205221_Englisch.pdf</h1> <p>Technical data sheet <br />AQUAFIN®-P4 <br />PU injection resin for crack-bridging</p> <p>Material number</p> <p>Package type</p> <p>Colour</p> <p>Units / pallet</p> <p>Pc/package</p> <p>205221003</p> <p>5.2 kg, set</p> <p>Honey yellow</p> <p>240,000</p> <p>1,000</p> <p>A-component: 2.5 kg, can</p> <p>220,000</p> <p>4,000</p> <p>B-component: 2.7 kg, can</p> <p>220,000</p> <p>4,000</p> <p>80,000</p> <p>1,000</p> <p>A-component: 5 kg, can</p> <p>84,000</p> <p>1,000</p> <p>B-component: 5.4 kg, can</p> <p>84,000</p> <p>1,000</p> <p>205221004</p> <p>10.4 kg, set</p> <p>Honey yellow</p> <p>Fields of application / waterproofing <br />For crack sealing <br />For water penetration <br />On dry and damp substrates <br />System component of AQUAFIN®-CJ1</p> <p>Product features <br />Polyurethane resin <br />Two component</p> <p>Advantages <br />Low viscosity <br />Cures to soft elastic <br />Excellent adhesion</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/3</p> <p>26/04/2026</p> <p>Technical data sheet <br />AQUAFIN®-P4 <br />Technical Data <br />Material properties <br />2 component system <br />polyurethane resin <br />Liquid <br />approx. 1.1 kg/dm³ <br />approx. 125 mPa*s <br />approx. 47 (after 21 hours) at 25 °C</p> <p>Product components <br />Base material <br />Consistency <br />Density (spec. weight) <br />Dynamic viscosity (20 °C) <br />Shore-A hardness (ISO 868)</p> <p>Mixing <br />1 Volume share <br />1 Volume share <br />approx. 3 minutes</p> <p>Mix ratio, component A <br />Mix ratio, component B <br />Mixing time</p> <p>Application <br />approx. 5 - 30 °C <br />approx. 30 minutes <br />approx. 5 hours <br />approx. 1.1 kg/l <br />approx. 10 - 30 °C</p> <p>Substrate temperature <br />Pot life <br />Final curing (20 °C) <br />Consumption per litre - voids <br />Application temperature</p> <p>Processing equipment <br />Aids/tools <br />Stirrer (approx. 300 rpm) <br />Hand lever press <br />Foot lever press <br />Suitable injection equipment <br />Injection packer <br />Mechanical grouting system (piston pump) <br />Mechanical grouting system (airless)</p> <p>Machine application <br />AQUAFIN®-P4 can be mechanically applied. For precise information, see the additional Technical Information No. 43.</p> <p>Preparing the substrate <br />Substrate quality class <br />Concrete</p> <p>Screed</p> <p>Plaster</p> <p>min. C20/25</p> <p>min. CT-C35-F5</p> <p>min. P Illa/P Illb</p> <p>Tensile adhesion strength ≥ 1,5 N/mm²</p> <p>≥ 1,5 N/mm²</p> <p>≥ 0,8 N/mm²</p> <p>Quality</p> <p>Age</p> <p>min. 28 days</p> <p>Application <br />Mixing <br />1. Store the material at +15 °C for 12 hours before use. <br />2. Add the hardener to the resin. <br />3. The hardener must run completely out of the container. <br />4. Mix thoroughly with the mixer until a homogeneous consistency is achieved. <br />5. Mixing time approx. 3 minutes. <br />6. Decant the mass into a clean bucket. <br />7. Stir carefully again.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/3</p> <p>26/04/2026</p> <p>Technical data sheet <br />AQUAFIN®-P4 <br />Application <br />1. Clear any drilling debris in the drilled holes using oil-free compressed air. <br />2. Insert the injection packer. <br />3. Seal the injected packer and crack zone on the surface approx. 15 cm wide with ASODUR-EKF. <br />4. After the crack insulation has cured, grout in the thoroughly mixed AQUAFIN-P4 using a grouting device. <br />5. After the resin has cured, remove the injection packer and plug the boreholes flush with the surface using ASOCRET-M30.</p> <p>Cleaning tools <br />Clean tools immediately after use with suitable solvent. The injection system must be cleaned at the end of work or in case of a longer <br />interruption to work. No material residues shall be allowed to dry and stick in the equipment. The cleaning agent or solvent to be used must <br />have a flash point above +21 °C. Please observe the specifications of the respective machine manufacturer.</p> <p>Storage conditions <br />Storage <br />Store in a frost-free, cool and dry place. At min. 15 - 25 °C for 12 months in the original canister. Promptly use opened container.</p> <p>Notes <br />Protect surfaces that are not to be treated from the effects of AQUAFIN®-P4! <br />In the event of water-conducting cracks, an initial injection of AQUAFIN®-P1 is necessary to stop the ingress of water. <br />Higher temperatures shorten the pot life. Lower temperatures increase the application and hardening times. The rate at which material is <br />consumed also increases at lower temperatures.</p> <p>Observe applicable safety data sheet!</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/3</p> <p>26/04/2026</p>
