SOLOFLEX_Product_information_GB_2616.pdf
2 页数
319.0 KB
Download
<h1>SOLOFLEX_Product_information_GB_2616.pdf</h1> <p>Product information <br />Tile adhesives/Thin-bed mortars</p> <p>SOLOFLEX <br />Flexible thin- and medium-bed adhesive <br />grey, C2 TE</p> <p>Technical Data: <br />Mix ratio: </p> <p>6.75 – 8.0 litres of water : 25 kg SOLOFLEX</p> <p>Application / <br />substrate temperature: </p> <p>+5°C to + 25°C</p> <p>Open time*: </p> <p>approx. 30 mins</p> <p>Foot traffic/ready to <br />grout*: </p> <p>after approx. 24 hrs</p> <p>Consumption: <br /> <br /> <br />Full service conditions*: </p> <p>approx. 2.3 kg/ m² with a 6 mm notched trowel <br />approx. 3.1 kg/ m² with an 8 mm notched trowel <br />approx. 3.7 kg/ m² with a 10 mm notched trowel <br />after approx. 7 days</p> <p>Reaction to fire: </p> <p>A1/A1fl</p> <p>Packaging: </p> <p>6 and 25 kg plastic bag</p> <p>TS/CoS/JD</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>26/16</p> <p>Areas of application: <br />• SOLOFLEX is a flexible thin-bed or medium-bed adhesive (up <br />to 10 mm) for the installation of porcelain, vitrified and <br />earthenware tiles and other ceramic finishes, mosaics and <br />natural stone, that is not sensitive to discolouration nor is <br />translucent. <br />• SOLOFLEX is suited for tiling to all substrates in accordance <br />with DIN 18157, part 1, e.g. concrete, aerated concrete, <br />plaster/render, cement-based and calcium sulphate based <br />heated and unheated (flow) screeds, masonry work, moisture <br />resistant plasterboard and gypsum fibre boards, composite <br />materials in expanded or extruded polystyrene with a mortar <br />coating and reinforcement layer embedded, etc. <br />• For tiling over mineral-based or dispersion-based <br />SCHOMBURG bonded waterproof membranes.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>*at +20 °C and 65 % relative humidity</p> <p>2 05430</p> <p>SOLOFLEX <br />Flexible thin- and <br />medium-bed adhesive <br />grey, C2 TE <br />Properties: <br />• Sag resistant <br />• Medium bed adhesive <br />up to 10 mm thickness <br />• For porcelain tiles <br />• For heated screeds <br />• For interior and exterior use <br />• Tested to <br />DIN EN 12004 C2 TE</p> <p>* Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>Product preparation: <br />Mix SOLOFLEX in a clean mixing bucket with clean water until <br />homogenous. Mixing ratio: 6.75 – 8.0 litres of water : 25 kg SOLOFLEX <br />Allow to stand for 3 minutes, then re-mix. Do not mix more SOLOFLEX than <br />can be used within the pot life. Spread the mixed adhesive over the <br />substrate surface and comb through with a notched trowel appropriate <br />to the tile size. Install the tiles within the adhesive open time. <br />When installing large format tiles or tiled finishes in more demanding <br />conditions or where there are temperature fluctuations, we recommend that <br />SOLOFLEX is modified with UNIFLEX®-B. The deformation to DIN EN <br />12002 is considerably increased and the adhesive open time extended. <br />To improve workability, mix UNIFLEX®-B with water and then mix with <br />SOLOFLEX until homogenous. <br />Mix ratio, highly deformable especially suitable for wet duty class B0 <br />(conforms to class C1E S2, deformation approx. 30 mm): <br />8.33 kg UNIFLEX-B : approx. 2 litres water : 25 kg SOLOFLEX</p> <p>1 Load-bearing substrate</p> <p>2 Priming the substrate, e.g. <br />with ASO®-Unigrund</p> <p>3 Adding the adhesive to a <br />measuring bucket</p> <p>4 Mixing the adhesive</p> <p>5 Setting out the wall</p> <p>6 Combing out the adhesive <br />bed</p> <p>7 Fixing the wall tiles</p> <p>8 Priming the substrate, e.g. <br />with ASO®-Unigrund</p> <p>9 Setting out the floor</p> <p>Mix ratio, highly deformable (conforms to class C2E S2, <br />deformation > 5 mm): <br />4.17 kg UNIFLEX-B : approx. 3.75 litres water : 25 kg SOLOFLEX <br />Mix ratio, deformable (conforms to class C2E S1, deformation > 2.5 mm): <br />2 kg UNIFLEX-B : approx. 5.4 litres water : 25 kg SOLOFLEX <br />Application: <br />The substrate must be dry, load-bearing, adequately flat, be free from <br />penetrating cracks and separating substances such as oils, paints, laitance <br />and loose areas. It must have a closed surface texture and exhibit surface <br />characteristics and strength consistent with its type. When installing tiles, the <br />substrate, its preparation and workmanship must conform to DIN 18157, <br />part 1. Prime absorbent substrates with ASO-Unigrund. <br />Heated floors are to be heated prior to installing tiles. The readiness of a <br />substrate to receive finishes is to be determined by the carbide (CM) <br />method and may not fall below the following values: <br />•CT ≤ 2.0% (when installing large format tiles 1.5%) <br />•CA/CFA unheated ≤ 0.5%, heated ≤ 0.3%</p> <p>10 Combing out the adhesive bed</p> <p>11 Applying a contact layer with large <br />format tiles</p> <p>12 Laying the floor tiles</p> <p>13 Finished area ready for use</p>
