Aufheizprotokoll_Heating report_SCHOMBURG-MONOFLEX-S2_EN_4923.pdf
2 页数
591.7 KB
Download
<h1>Aufheizprotokoll_Heating report_SCHOMBURG-MONOFLEX-S2_EN_4923.pdf</h1> <p>Heating report for ceramic coverings on ‘green’ cementbased screeds with MONOFLEX-S2 <br />Client: <br />Building / <br />property: <br />Building section / part / <br />storey / apartment: <br />Building part:</p> <p>REQUIREMENTS <br />Before starting installation work, the cement-based screed must be checked for quality, final screed thickness, suitability, <br />load-bearing capacity and age. Furthermore, the moisture content must be determined using the CM method. The information <br />in the technical data sheet for MONOFLEX-S2 must be observed.</p> <p>Documentation <br />1. Nature of screed (if applicable manufacturer) <br />Binder used: <br />days <br />Defined setting times: <br />2. End of work on the cement-based screed: Date <br />3. Start of functional heating: Date <br />- 28 days after completion of the tiling work at the earliest <br />- Start of functional heating with a flow temperature of +20°C for 3 days at a constant flow temperature <br />(without night setback and/or interruption): Date <br />up to <br />, max. flow temperature</p> <p>°C</p> <p>4. Raising the flow temperature to +25°C from day 4 to day 7 of functional heating <br />(without night setback and/or interruption): Date <br />up to <br />, max. flow temperature</p> <p>°C</p> <p>5. Raising the flow temperature to +35°C from day 7 to day 10 of functional heating <br />(without night setback and/or interruption): Date <br />up to <br />, max. flow temperature</p> <p>°C</p> <p>6. Lowering the flow temperature to +20°C from day 10 to day 11 of functional heating <br />(without night setback and/or interruption): Date <br />up to <br />, max. flow temperature</p> <p>°C</p> <p>7. Transition to control mode with a maximum flow temperature of +30°C for subsequent use from day 12 of functional heating. <br />Date <br />, max. flow temperature <br />°C</p> <p> The rooms were ventilated without draughts and all windows and external doors were closed after the floor heating system was <br />switched off <br />Yes <br />No <br /> Heated floor surface was free of coverings during functional heating <br />Yes</p> <p>No</p> <p>The system was released for further construction work at an outside temperature of</p> <p>The system was out of operation: Yes</p> <p>No</p> <p>The floor was heated with a flow temperature of</p> <p>°C</p> <p>°C</p> <p>RAc/KK/Tet 49/23</p> <p>No</p> <p>Page 1/2</p> <p> Was the functional heating interrupted? Yes <br />until <br />If yes: from date</p> <p>Heating report for ceramic coverings on ‘green’ cementbased screeds with MONOFLEX-S2 <br />NOTE <br />Depending on the heat output of the heat generator, functional heating may need to be carried out in sections. However, all <br />heating circuits within a screed field must be heated simultaneously. <br />When switching the floor heating system off and on during the construction phase and later use, the floor construction must <br />be protected from cooling down and heating up too quickly.</p> <p>Confirmation</p> <p>Place/date</p> <p>Place/date</p> <p>Client/principal <br />Stamp/signature</p> <p>Project director/architect <br />Stamp/signature</p> <p>Heating installer <br />Stamp/signature</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstr. 2–8 · D-32760 Detmold (Germany) · phone +49-5231-953-00 · fax +49-5231-953-333 · www.schomburg.com</p> <p>Page 2/2</p> <p>RAc/KK/Tet 49/23</p> <p>Place/date</p>
