CRISTALLFUGE-Flex_Produktinformation_0122.pdf
2 页数
405.5 KB
Download
<h1>CRISTALLFUGE-Flex_Produktinformation_0122.pdf</h1> <p>joint mortar</p> <p>Application <br />1. Mix CRISTALLFUGE-FLEX with clean water in a clean mixing bucket. <br />Add 4.0-5.0 l water depending on the desired consistency, add 25 kg <br />CRISTALLFUGE-FLEX, and then stir into a homogeneous, smooth <br />compound. We recommend mixing with a suitable stirrer. After an <br />activation time of 4 min., the joint mortar is stirred again. In order to <br />avoid colour differences, the mix ratio must always be kept the same. <br />2. CRISTALLFUGE-FLEX is added to the wall and floor areas with a suitable <br />jointing board and pulled diagonally to the joint cleanly, so that the joint <br />cross-section is filled completely. Do not scatter dry joint mortar powder. <br />3. After applying the joint mortar (control via finger test), wash the surface <br />first with a moist sponge board. After approx. 10-15 minutes, wash off <br />again with the sponge board. <br />Please refer to the currently valid technical data sheet for <br />additional instructions.</p> <p>High-strength flex joint mortar, <br />3–20 mm, CG2 W A <br />Properties <br />• Rapid setting <br />• Good binding and wash-off properties <br />• 3 - 20 mm joint width, curing without cracks <br />• For porcelain stoneware and many other coverings <br />• Water-repellent <br />• Frost/thaw-resistant <br />• Suitable for floor and wall heating systems <br />• Colours matched to the ESCOSIL-2000 and <br />ESCOSIL-2000-ST silicone system <br />• Fulfils AgBB formula requirements. <br />Areas of use <br />• CRISTALLFUGE-FLEX is suitable for grouting <br />porcelain stoneware, vitrified tiles and stoneware <br />boards, brick tiles, artificial stone, facing bricks, <br />veneer and floor bricks in baths, showers, and <br />living areas, on terraces, balconies and loggias, <br />and façades, in swimming pools, commercial <br />and industrial facilities, as well as heating flow <br />screeds for joint widths from 3–20 mm. <br />• CRISTALLFUGE-FLEX is also suitable for grouting <br />many natural stones.</p> <p>Application <br />• After the bedding mortar/tile adhesive sets, scratch out the joints <br />sufficiently deep. <br />• Next, clean the tiled finish sufficiently damp. <br />• The bedding mortar must be fully set, since otherwise discolourations in <br />the grout finish could result. <br />• Pre-moisten strongly absorbing coverings with water equally. <br />• Joint edges must be clean and free of separating substances. <br />• The time of grouting of the tiles set in the thin-bed depends on the thinbed mortar and amounts to approx. 3 to 72 hours. In case of thick-bed <br />laying, the mortar bed must be sufficiently firm and equally dry. <br />• Do not grout on surfaces with different surfaces temperatures (e.g. due to <br />sun exposure). <br />• The consistency of joint mortar must be specified depending on the <br />absorbency of the covering and substrate to be grouted.</p> <p>Consumption table <br />Tiles/boards <br />format (in cm)</p> <p>Joint width <br />(in mm)</p> <p>20.0 × 20.0</p> <p>3.0</p> <p>20.0 × 20.0 <br />30.0 × 30.0 <br />30.0 × 30.0</p> <p>Joint depth <br />(in mm)</p> <p>0.5</p> <p>4.0</p> <p>8.0</p> <p>0.7</p> <p>5.0</p> <p>8.0</p> <p>0.6</p> <p>5.0</p> <p>15.0</p> <p>1.1</p> <p>30.0 × 60.0</p> <p>3.0</p> <p>10.0</p> <p>0.3</p> <p>40.0 × 40.0</p> <p>5.0</p> <p>10.0</p> <p>0.6</p> <p>90.0 × 20.0</p> <p>3.0</p> <p>10.0</p> <p>0.4</p> <p>30.0 × 5.0</p> <p>8.0</p> <p>10.0</p> <p>3.6</p> <p>24.0 × 11.5</p> <p>10.0</p> <p>12.0</p> <p>3.2</p> <p>24.0 × 11.5</p> <p>10.0</p> <p>20.0</p> <p>5.3</p> <p>v er</p> <p>y lo</p> <p>w e m is</p> <p>s</p> <p>* Informationen über das Emissionsniveau von flüchtigen Stoffen in <br />der Raumluft, die bei Inhalation Gesundheitsrisiken, auf einer Skala <br />von Klasse A + (sehr emissionsarm) bis C (hohe Emissionen), darstellen.</p> <p>1 Available floor surface, bonding bed is set</p> <p>2 CRISTALLFUGE-FLEX, suitable tools</p> <p>3 Fill the joint mortar into a clean mixing bucket</p> <p>4 Mix the joint mortar</p> <p>5 Apply the joint mortar</p> <p>6 Sliding diagonally across excess joint mortar</p> <p>7 Emulsify the joint mortar after setting</p> <p>8 Rinsing off surfaces diagonally to the joint <br />direction</p> <p>9 Finished and jointed floor surface</p> <p>Note: The adjacent floor jointing process is <br />also valid for wall areas</p> <p>Approx. <br />consumption in m2 <br />(in kg)</p> <p>8.0</p> <p>io n</p> <p>joint mortar <br />CRISTALLFUGE-FLEX</p> <p>joint mortar <br />CRISTALLFUGE-FLEX <br />High-strength flex joint mortar, 3–20 mm <br />CG2 W A</p> <p>Cement, high-quality additives, cementitious special <br />aggregates</p> <p>Colours</p> <p>cement grey, medium grey, graphite, sand grey</p> <p>Classification</p> <p>EN 13888 CG2 W A</p> <p>Application temperature</p> <p>+5 °C to +25 °C</p> <p>Pot life*</p> <p>approx. 30 minutes</p> <p>Water addition</p> <p>4.0–5.0 l water: 25 kg CRISTALLFUGE-FLEX <br />0.8–1.0 l water: 5 kg CRISTALLFUGE-FLEX</p> <p>Consumption</p> <p>see consumption table</p> <p>Foot traffic* <br />Withstands loads*</p> <p> fter approx. 2 hours <br />a <br />after approx. 7 days</p> <p>Packaging</p> <p>25 kg foil sack <br />5 kg foil bag</p> <p>* at +23 °C and 50 % rel. humidity</p> <p>Colours*</p> <p>cement grey</p> <p>medium grey <br />* Colour deviations are due to printing technology.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>graphite</p> <p>sand grey</p> <p>01/22 TS/Tet/LiW</p> <p>Basis</p> <p>Subject to change without prior notification. The valid issue of the corresponding technical bulletin legally applies.</p> <p>Technical data</p>
