ASOCRET-IM_205523_Englisch.pdf
3 页数
1.0 MB
Download
<h1>ASOCRET-IM_205523_Englisch.pdf</h1> <p>Technical Datasheet <br />ASOCRET-IM <br />Crystalline repair mortar for concrete, waterproofing</p> <p>Material number</p> <p>Contents</p> <p>Unit of quantity</p> <p>Packaging</p> <p>Colour</p> <p>205523001</p> <p>25</p> <p>KG</p> <p>Bag</p> <p>Grey</p> <p>Advantages <br />watertight <br />Vapour permeable <br />Easy application <br />Supports self-repair of the concrete <br />Can also be used on damp substrate</p> <p>Product features <br />Capillary active mortar <br />Increased active crack healing in concrete <br />Chloride-free</p> <p>Areas of application <br />For water tight filling of open cracks and holes <br />As coving mortar <br />Suitable for negative water pressure</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />1/3</p> <p>01/07/2023</p> <p>Technical Datasheet <br />ASOCRET-IM <br />Technical Data <br />Material properties <br />Product components <br />Base material <br />Consistency <br />Grain size max <br />Compressive strength (28 days)</p> <p>1 component system <br />Pre-blended dry mortar <br />Filler consistency <br />< 1 mm <br />approx. 20 N/mm²</p> <p>Mixing <br />Mixing time <br />Water addition <br />Water addition (percentage)</p> <p>approx. 3 minutes <br />From 3.75 l to 4.25 l per 25 kg <br />from 15 % to 17 %</p> <p>Application <br />Substrate/application temperature <br />Pot life <br />Method of application, max. layer thickness per application step <br />Consumption pro m² and mm layer thickness</p> <p>from 5 °C to 30 °C <br />approx. 30 minutes <br />to 10 mm <br />approx. 1.7 kg/m²</p> <p>Application technology <br />Aids/tools <br />Stirrer (approx. 500-700 rpm) <br />Suitable mixing paddle <br />Trowel <br />Flat trowel <br />Brush</p> <p>Suitable substrate <br />Concrete</p> <p>Substrate preparation <br />Requirement for substrate <br />1. <br />2. <br />3. <br />4. <br />5.</p> <p>Firm <br />Load-bearing <br />Pore open <br />Clean <br />Absorbent</p> <p>Preparing the surface <br />1. Dense and smooth substrates must be roughened accordingly using suitable measures (e.g. sand, high-pressure, water or shot blasting). <br />2. A load-bearing substrate is a precondition for a long-lasting bond between the substrate and coating system. Less adhesive and bond-damaging <br />substances must be completely removed. High-pressure water jetting (> 400 bar; < 2000 bar) and jets with fixed blasting agents are suitable <br />measures. The last application step must be cleaning with pressure water jetting. <br />3. Water ingress must be stopped in advance with FIX 10-S or FIX 20-T. <br />4. Pre-moisten the dry substrate so that it is matt damp at the time of application. <br />5. The formation of puddles must be avoided.</p> <p>Usage <br />Mixing <br />Add water (From 3.75 l to 4.25 l per 25 kg) to a clean mixing bucket and mix with 25 kg of the powder component to produce a <br />homogeneous, lump-free mass.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />2/3</p> <p>01/07/2023</p> <p>Technical Datasheet <br />ASOCRET-IM <br />Application <br />1. ASOCRET-IM can be applied with a layer thickness of up to 10 mm per application step. <br />2. Structural cracks are to be prised open up to a width of approx. 20 mm and a depth of approx. 25 mm. Screen the edges with AQUAFIN®-IC <br />and seal wet in wet with ASOCRET-IM flush with the surface. <br />3. Screen the substrate with AQUAFIN®-IC and then apply the ASOCRET-IM "wet in wet" with an edge height of approx. 4 cm in a rounded form. <br />After approx. 1–3 hours, rework ASOCRET-IM with AQUAFIN®-IC. If this is not possible during this period, the surface should be roughened <br />again after totally hardening and then coated with AQUAFIN®-IC. <br />4. After approx. 1–3 hours, rework ASOCRET-IM with AQUAFIN®-IC. If this is not possible during this period, the surface should be roughened <br />again after totally hardening and then coated with AQUAFIN®-IC. <br />5. ASOCRET-IM must be protected against rapid water removal using suitable protective measures!</p> <p>Cleaning tools <br />Rinse tools with water immediately after use.</p> <p>Storage conditions <br />Storage <br />Cool, dry, protected from sunlight. Min. 12 months in the original canister. Promptly use opened container.</p> <p>Disposal <br />Product leftovers can be disposed of in accordance with disposal code AVV 17 01 01.</p> <p>Notes <br />Protect surfaces that are not to be treated from the effects of ASOCRET-IM! <br />Do not use on frozen substrates. <br />ASOCRET-IM cannot be admixed as an additive to concrete or plaster, i.e. must not be admixed with such products. <br />The reaction between ASOCRET-IM and the free lime in the concrete can result in slight efflorescence. This is not a defect and can be <br />brushed off. <br />Different colouring depends on the different moisture content in the concrete.</p> <p>GISCODE: ZP1</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you <br />in the case of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description <br />does not release the user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued.</p> <p>SCHOMBURG GmbH & Co. KG · Aquafinstr. 2–8 · D-32760 Detmold (Germany) · Tel. +49-5231-953-00 · Fax +49-5231- 953-333 · schomburg.com <br />3/3</p> <p>01/07/2023</p>
