Folder_Aquafin-1K_GB_1121.pdf
6 页数
657.6 KB
Download
<h1>Folder_Aquafin-1K_GB_1121.pdf</h1> <p>Mineral based <br />waterproof slurry</p> <p>AQUAFIN®-1K <br />One component mineral based waterproof slurry <br />„Negative waterproofing!“. <br />Problems solved.</p> <p>Why <br />AQUAFIN®-1K <br />AQUAFIN-1K is a rigid waterproof slurry for the inside and <br />the outside. It resists the sulfate and is suitable for all types of <br />support in the construction. It is open to diffusion, resistant to <br />ageing and UV. In addition, it is certified waterproof against <br />negative water pressure up to 1.5 bar.</p> <p>How does it work? <br />After application, a strong bond is created between the <br />support and AQUAFIN-1K, which becomes an integral part <br />of the substrate. AQUAFIN-1K thus forms a waterproof <br />barrier.</p> <p>Technical Data <br />Basis</p> <p>sand/cement, polymer modified</p> <p>Density of mixed <br />mortar</p> <p>approx. 1.85 g/m³</p> <p>Adhension strength</p> <p>> 0.5 N/mm² (ASTM D 4541:2002)</p> <p>Pot life</p> <p>approx. 60 min.</p> <p>Substrate /application +5° C to + 35° C <br />temp <br />Comp. strength 28d</p> <p>approx. 15 N/mm² (ASTM C 579)</p> <p>Packaging</p> <p>25 kg bags, 6 kg bags</p> <p>Product application</p> <p>1. Pour the amount of water needed in a clean container <br />2. Pour the total contents of a bag of AQUAFIN-1K and mix <br />until a homogeneous lump free mix is achieved. A mixing <br />time of approx. 2–3 minutes is necessary. <br />3. Apply AQUAFIN-1K by brush, trowel or with a suitable <br />machine. <br />Tools: <br />Drilling machine | Mixer | Trowel | Notched trowel</p> <p>Application domains <br />1. Subsequent negative waterproofing against water <br />infiltration <br />2. External waterproofing of new and old construction <br />3. W <br /> eathered or greenery covered concrete cold roofs <br />above underground garages, prefabricated garages <br />4. Service water containers, waste water containers and <br />pipes <br />5. Retaining walls and sluices <br />6. Horizontal waterproofing in/on the walls and basement</p> <p>Consumption <br />Waterproofing of building elements: <br />Soil moisture / non-standing runoff water: <br />• 3.5 kg/m²/approx. 2.0 mm <br />Standing runoff water / water under pressure: <br />• 4.5 kg/m²/ approx. 2.5 mm <br />Subsequent waterproofing of the components in <br />contact with the earth: <br />Soil moisture / non-standing runoff water: <br />• Minimum 3.5 kg/m²/approx. 2.0 mm <br />Standing runoff water / water pressure: <br />• Minimum 5.3 kg/m²/approx. 3.0 mm <br />Waterproofing according to DIN 18195 part 7 / <br />water under pressure from the inside: <br />• Minimum 3.5 kg/m²/approx. 2.0 mm</p> <p>schomburg.de</p> <p>What is negative <br />waterproofing? <br />The typical case of a negative waterproofing exists when <br />water penetrates a wall by a face and the waterproofing <br />layer is applied on the opposite side. To make a negative <br />waterproofing is more difficult than to make a positive <br />waterproofing because then, the water has crossed the <br />construction element, has arrived at the level for example, <br />the layer of paint or tile flooring and tries to take it off from <br />the wall.</p> <p>Example of construction where a <br />negative waterproofing is <br />required: <br />• Internal waterproofing of cellar walls <br />• External waterproofing of water tanks <br />• Internal waterproofing of elevator shafts <br />• Internal waterproofing of tunnels <br />• Waterproofing of low permeable floors</p> <p>Subject to changes. Consult current Technical Data Sheet for most recent information. <br />11/21 HS/JM/LiW</p> <p>SCHOMBURG GmbH <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49 - 5231- 953 - 00 <br />fax <br />+ 49 - 5231- 953 -333 <br />www.schomburg.com</p>
