Planungs-_und_AnwendungsratgeberBWA_INT_EN_3626.pdf
30 页数
2.6 MB
Download
<h1>Planungs-_und_AnwendungsratgeberBWA_INT_EN_3626.pdf</h1> <p>SCHOMBURG <br />Problems Solved.</p> <p>PLANNING AND <br />APPLICATION CONSULTANT <br />For building waterproofing <br />and restoration</p> <p>schomburg.com</p> <p>Contents <br />4 PLANNING AND PREPARATION <br />4 Planning waterproofing and preserving value <br />5 Water impact classe <br />6 Preparing substrates</p> <p>8</p> <p>PROBLEMS SOLVED <br />FOR ANY REQUIREMENT <br />Restoring, renovating, and modernising older existing buildings has become <br />increasingly important in recent years. The most important aspect for permanently <br />maintaining a building is protection against moisture. <br />It’s imperative that the waterproofing is reliable. SCHOMBURG possesses <br />decades of experience in this area, and we offer you an assortment of products <br />that are matched exactly to each other.</p> <p>WATERPROOFING SYSTEMS</p> <p>8 Cellar exterior waterproofing <br /> <br />- Bituminous <br /> <br />- Cementitious <br />12 Cellar interior waterproofing <br />14 Retroactive horizontal barrier <br /> - with liquid injection material <br /> - with paste injection material <br />18 Salt-loaded substrate <br />20 Renovation system with insulating effect <br /> - For areas exposed to moisture <br /> - Without additional waterproofing measures <br />24 Floor renovation <br />26 Ground level installation solutions <br />28 Garage repairs <br />30 Facade impregnation <br />32 Sewage treatment plants <br />34 Service water containers <br />36 Protection of reinforced concrete <br />38 Vapour barrier for damp substrates <br />40 Crack repairs <br /> - substrates <br /> - wall surfaces <br />44 Retrospective execution of construction joints <br />48 Execution of construction joints in concrete construction <br /> - with crystalline waterstop sheet <br /> - with injection hose system <br /> - with elastomer swelling joint tape <br />52 Concrete surface protection</p> <p>54 GENERAL INFORMATION <br /> <br />for planning and execution</p> <p>Further information about SCHOMBURG and our product <br />systems can be found at www.schomburg.com.</p> <p>56 Joint tapes</p> <p>3</p> <p>Waterproofing | Planning and preparation</p> <p>Water impact classes</p> <p>Planning and using waterproofing <br />Protect and preserve value</p> <p>Soil moisture and non-rising damp <br />in floor slabs and walls in contact with the ground <br />This exposure class applies where <br />highly permeable soil is present (k > <br />10⁻⁴ m/s) and the design water level (HGW/ <br />HHW) is ≥ 50 cm <br />below the lowest waterproofing layer.</p> <p>This impact can be waterproofed using a <br />polymer-modified bituminous thick layer <br />coating (PMBC) or a cementitious, crackbridging waterproofing slurry (MDS).</p> <p>Soil moisture and non-rising damp in floor slabs <br />and walls in contact with the ground with drainage <br />This exposure class applies where <br />the soil has low permeability <br />(k ≤ 10⁻⁴ m/s) and the design water level <br />(HGW/HHW) is ≥ 50 cm below the lowest <br />waterproofing layer. The resulting water <br />accumulation is removed by permanently <br />functioning drainage.</p> <p>If the drainage does not function, pressing <br />water is present. This impact can be <br />waterproofed using a polymer-modified <br />bituminous thick layer coating (PMBC) or a <br />cementitious, crack-bridging waterproofing <br />slurry (MDS).</p> <p>Moderate exposure to pressure water <br />This impact class is present when <br />groundwater, accumulating water, or flood <br />water affect the component directly in the <br />ground. Up to a water column of ≤ 3 m, the <br />building component may be waterproofed <br />with polymer-modified bituminous thick layer</p> <p>Protecting a building against penetrating moisture, ensuring a pleasant living <br />environment on the interior, and granting the building eternal youth: Accepting these <br />challenges means working with knowledge and precision to implement projects to <br />the satisfaction of the building owner. <br />Living and working in a hygienic environment with a pleasant <br />temperature that is healthy above all else is not a matter of <br />course. To ensure long-term preservation of the value of a <br />building, carefully planned waterproofing solutions are needed. <br />Every building is continuously exposed to external environmental <br />conditions and must be adjusted individually in accordance with <br />the surrounding influences. The waterproofing products and <br />system components must be compatible with each other and <br />matched to suit each other. <br />From substrate preparation to waterproofing for waste water <br />treatment plants and crack waterproofing, SCHOMBURG <br />offers a complete package for every thinkable challenge. <br />Building components in the ground especially require highquality, professional implementation of waterproofing. Follow-up</p> <p>improvements or even essential restorations involve high costs <br />and require a lot of time, since after the building pit is filled in, the <br />exterior area is difficult to access. For this reason, <br />SCHOMBURG offers optimised solutions for cellar exterior <br />waterproofing in particular to ensure a water-tight cellar. <br />Selection of matching waterproofing components for cellar <br />masonry depends on a variety of factors. On the one hand, this <br />depends on the use of the cellar, while on the other, various <br />so-called “water impact classes” are involved. In this case, the <br />type and method of penetrating moisture are referred to. Pressing <br />groundwater from outside required another type of <br />waterproofing application than normal ground moisture. The <br />correct application is regulated in the technical documents. <br />This specifies corresponding waterproofing procedures for <br />corresponding water impact classes.</p> <p>coating (PMBC). The use of cementitious, <br />crack-bridging waterproofing slurry is not <br />intended for this impact class and may only <br />be agreed to separately with the respective <br />employer.</p> <p>High exposure to pressure water <br />This impact class is present when <br />groundwater, accumulating water, or flood <br />water affect the component in direct ground <br />and the foundation depth is ≥ 3 m. The impact <br />class distinguishes between two situations. <br />Situation 1: The groundwater and flood water <br />level is beneath the foundation depth.</p> <p>Situation 2: The groundwater and flood water <br />level is 3 m above the foundation depth. With <br />this exposure, the use of PMBC or flexible <br />polymer-modified thick layer coatings (FPD) <br />are to be agreed separately with the <br />customer.</p> <p>Non-pressurised water on earth-covered slabs <br />This impact class is present if an earthcovered ceiling is impacted directly by <br />precipitation with a water load of ≤ 10 cm <br />accumulation depth and the measured water</p> <p>level is ≥ 30 cm below the lowest point of the <br />ceiling. This impact can be waterproofed <br />using a polymer-modified bituminous thick <br />layer coating (PMBC).</p> <p>Splash water at the wall base and capillary water in and under walls in <br />direct ground <br />The “wall base” describes the area approx. <br />20 cm below the top edge and approx. <br />30 cm above the top edge. In this area, the <br />building component must be waterproofed <br />against penetrating moisture with polymermodified bituminous thick layer coating or a</p> <p>cementitious, crack-bridging waterproofing <br />slurry. To avoid rising capillary water in walls <br />in direct ground, it is possible to use a <br />cementitious, crack-bridging <br />waterproofing slurry as profile waterproofing.</p> <p>4 <br />5</p> <p>Waterproofing | Preparing substrates</p> <p>Preparing substrates <br />for ideal results</p> <p>A sustainably functioning waterproofing requires a thorough and <br />carefully prepared building surface to be treated. After all, the <br />finished waterproofing is only as good as the substrate will <br />allow. <br />The waterproofing materials must harmonise with the substrate <br />and require the best possible bonding for secure and long-lasting sealing function. For this reason, substrate pretreatment with <br />its specific requirements is particularly important. The technical <br />documents specify the basic principles and details like the <br />evenness, burr removal, and cleaning, as they apply to every <br />user or installer. <br />The ideal pre-treatment of the substrate is based on the respective present waterproofing situation. <br />For example, waterproofing on basement walls requires other <br />procedures than with coatings in garages. Depending on the <br />relevant area, there are different system solutions for the <br />respective application area.</p> <p>Before any waterproofing measures, a professional building <br />condition analysis of the substrate must be completed. In case of <br />concrete substrates, bubble formation frequently results in the still <br />wet coating. This is due to the air voids that are hardly visible <br />and often covered with concrete paste on the surface of the <br />concrete. The air trapped in the pores expands due to exposure <br />to sunlight and continuously pushes outwards. In this case, the <br />fresh coating is pressed away from the substrate. This is <br />prevented by removing the cement paste layer using diamond <br />grinding or shot blasting. In case of more stubborn concrete <br />paste, sandblasting may even be necessary for clean removal. <br />The open pores may then be filled with suitable mortar or with <br />the right SCHOMBURG waterproofing following application <br />of a primer. <br />Thanks to these work steps, the substrate is pre-treated optimally <br />so that the waterproofing is able to be completed functionally <br />after the drying phase of the mortar.</p> <p>Application</p> <p>The substrate must be load-bearing, fine-pored, and free of dirt <br />and dust. Unevenness and ridges must be evened out meticulously. <br />As previously discussed in the building condition analysis, open <br />butt joints up to 5 mm and surface profiles and unevenness of <br />stones (e.g. plaster grooves on brickwork or heavy concrete <br />blocks) must be levelled using grouting, e. g. with AQUAFIN-1K. <br />Depressions that are not closed and larger than 5 mm, e.g. mortar <br />pockets or damaged areas must be closed with mortar, e.g. using <br />ASOCRET-M30. <br />Furthermore, the surface must be free of gaping cracks and <br />adhesion inhibiting substances, e.g. oil, paint, laitance layers, and <br />loose components. On the floor slabs, laitance layers must be <br />thoroughly removed mechanically down to the solid core to ensure <br />a high level of bonding. The base slab transition, which is a <br />sensitive, delicate area, should be pre-treated with slurry using <br />AQUAFIN-1K. Next, a coved fillet is applied while still wet using <br />ASOCRET-M30. Alternatively, the coved fillet area can be <br />applied using ASO-Joint-Tape-2000-S together with <br />AQUAFIN-RB400. After curing completely, the coved fillet</p> <p>area, including 15 cm of the front side, is also covered with <br />AQUAFIN-RB400. <br />The substrate should be pre-wetted so that it is matt damp while <br />applying the waterproofing layer. Strongly absorbent substrates <br />like aerated concrete must be primed with AQUAFIN-Primer <br />for improved adhesion. On metal substrates, use ASODUR-SG3 <br />(including quartz sand sprinkling) as a pore-sealed primer. If <br />ASOCRET-HFF is used to level off the surface in large layer <br />thickness widths (up to 30 mm), the process is the same. If <br />dampness from the rear is expected, then use <br />ASODUR-SG3-superfast instead. <br />Ideal substrates consist of dense concrete, cement-based screeds, <br />P II and P III plaster, and fully grouted masonry work. Formwork <br />and heavy concrete blocks, as well as uneven masonry must be <br />levelled with cement-based mortar.</p> <p>6 <br />7</p> <p>Waterproofing | Cellar exterior waterproofing</p> <p>Application</p> <p>Cellar exterior waterproofing for new <br />and existing buildings with bituminous <br />thick layer coatings (PMBC) <br />4</p> <p>1. Level the substrate <br />(as required) <br />Surface levelling with ASOCRET-M30 in <br />a single application or AQUAFIN-1K in <br />a minimum of two applications by means <br />of trowel or with suitable spray equipment.</p> <p>2. Waterproof the wall-floor <br />transition <br />Install a cementitious sealing cove in the <br />wall-floor transition with ASOCRETM30. First apply a bonding slurry. This <br />can consist of ASOCRET-M30 or <br />AQUAFIN-1K. Alternatively, the sealing <br />cove can be made of <br />ASO-Joint-Tape-2000-S.</p> <p>3. Waterproof pipe penetrations <br />Apply COMBIDIDC-2K-CLASSIC or <br />COMBIDIDC-2K-PREMIUM with a 4 <br />mm notched trowel and smooth it, adhere <br />the ADF-Pipe-Gasket without wrinkles <br />and then process it covering the whole <br />area.</p> <p>4. Base waterproofing transition <br />Apply AQUAFIN-RB400 in at least <br />two application steps using a brush, flat <br />trowel, or suitable spray equipment. <br />Application at least 30 cm above and at <br />least 20 cm below ground level.</p> <p>5. Primer <br />Before applying COMBIDIC-2KPREMIUM or COMBIDIDC-2KCLASSIC, the substrate must be primed <br />with ASOL-FE diluted 1:5 with water.</p> <p>6. P <br /> MBC waterproofing <br />Apply COMBIDIC-2K-PREMIUM, <br />COMBIDIC-2K-CLASSIC using trowel <br />techniques with exposure-based layer <br />thickness. Apply the bituminous thick layer <br />coating with an overlap of at least 10 cm <br />on the base waterproofing (figure 4).</p> <p>7. P <br /> rotection and drainage plates <br />After drying out the waterproofing layer, <br />apply bituminous thick layer coating in <br />dollops to the uncovered side of a <br />suitable protection and drainage element, <br />and then press it onto the waterproofed <br />substrate.</p> <p>8. Perimeter insulation <br />Adhere the insulation in accordance with <br />the manufacturer’s specifications closefitting and offset covering the whole area <br />using COMBIDIC-2K-CLASSIC or <br />COMBIDIC-2K-PREMIUM.</p> <p>3</p> <p>9</p> <p>1</p> <p>5</p> <p>6</p> <p>7</p> <p>8</p> <p>2</p> <p>A building envelope that remains permanently dry and free from <br />damage starts in the ground: basements, in particular, are <br />exposed to significant moisture stress. External basement <br />waterproofing using bitumen offers a reliable, system-based <br />solution for the long-term protection of structural elements in <br />contact with the ground against moisture, water and mould <br />growth. <br />Whether for new builds or refurbishments, the system provides a <br />seamless, joint-free waterproofing membrane that bridges cracks <br />and offers reliable protection even under varying conditions such <br />as ground damp or water under pressure.</p> <p>COMPONENTS <br />AQUAFIN-1K <br />ASOCRET-M30 <br />AQUAFIN-Primer <br />ADF-Rohrmanschette <br />AQUAFIN-RB400 <br />COMBIDIC-2K-CLASSIC / <br />COMBIDIC-2K-PREMIUM <br />COMBIDIC-1K-S <br />ASOL-FE <br />ADF-Rohrmanschette <br />ASO-Verstärkungseinlage</p> <p>8 <br />9</p> <p>Waterproofing | Cellar exterior waterproofing</p> <p>Cellar exterior waterproofing for new <br />and existing buildings with rapid <br />cementitious waterproofing (FPD)</p> <p>Application</p> <p>4 <br />3</p> <p>5</p> <p>6</p> <p>1</p> <p>1. Level the substrate <br />(as required) <br />Surface levelling with ASOCRET-M30 in <br />a single application or AQUAFIN-1K in <br />a minimum of two applications by means <br />of trowel or with suitable spray equipment.</p> <p>2. Waterproof the wall-floor <br />transition <br />Install a cementitious sealing cove in the <br />wall-floor transition with ASOCRET-M30. <br />First apply a bonding slurry. <br />This can consist of ASOCRET-M30 <br />or AQUAFIN-1K. Alternatively, the <br />sealing cove can be made of <br />ASO-Joint-Tape-2000-S.</p> <p>3. Waterproof pipe penetrations <br />Apply AQUAFIN-RB400 with a 4 mm <br />notched trowel and smooth it, adhere the <br />ADF-Pipe-Gasket) without wrinkles <br />and then process it covering the whole <br />area.</p> <p>4. FPD-MDS waterproofing <br />Apply AQUAFIN-RB400 with a <br />trowel/brush or the spray technique with <br />a load case-appropriate layer thickness.</p> <p>5. Protection and drainage plates <br />After the waterproofing layer has dried, <br />the protective layers can be bonded to <br />cover the whole area with a mixture of <br />AQUAFIN-RB400 / quartz sand <br />0.1—0.35 mm and a suitable notched <br />trowel using the Buttering-Floating method.</p> <p>6. Perimeter insulation <br />Bond the insulation tightly with <br />AQUAFIN-RB400 and offset, such that <br />it covers the whole area in accordance <br />with the manufacturer's instructions.</p> <p>2</p> <p>Reliable basement waterproofing is crucial for the long term <br />protection of the building structure. Mineral based external <br />basement waterproofing offers a modern, high performance <br />solution for waterproofing structural elements in contact with the <br />ground and ensures that basement rooms remain permanently dry <br />and mould-free. <br />The system is based on high quality, cement bound waterproofing <br />slurries, which are characterised by their water-impermeable, <br />vapour-permeable and durable properties. They are suitable for a <br />range of load conditions and meet the requirements of current <br />standards for the waterproofing of structural elements in contact <br />with the ground.</p> <p>COMPONENTS <br />AQUAFIN-Primer <br />AQUAFIN-1K <br />ASOCRET-M30 <br />ADF-Rohrmanschette <br />AQUAFIN-RB400 <br />ASO-Dichtband-2000-S</p> <p>10 <br />11</p> <p>Waterproofing | Cellar interior waterproofing</p> <p>Retrospective basement interior waterproofing in existing buildings in the <br />flexible system with radon protection</p> <p>4</p> <p>1</p> <p>5</p> <p>6</p> <p>3</p> <p>Application</p> <p>1. Levelling and pre-sealing <br />Levelling of the exposed, load-bearing <br />wall surfaces and application of the <br />pre-seal in one application step with <br />ASOCRET-M30 as a levelling and <br />waterproof plaster. Treat the wall surfaces <br />with ESCO-Fluat beforehand.</p> <p>2. Waterproof the wall-floor <br />transition <br />Install a cementitious sealing cove in the <br />wall-floor transition with ASOCRET-M30.</p> <p>3. W <br /> aterproof wall surfaces <br />(crack-prone) <br />After curing the surfaces, <br />AQUAFIN-RB400 is applied in two <br />application steps using a brush/trowel or <br />spray techniques.</p> <p>4. Splatterdash coat <br />A fully covering splatter-dash coat of <br />THERMOPAL-SP is applied to the <br />waterproofed substrate for improved <br />bonding of the following restoration <br />plaster.</p> <p>5. Apply restoration plaster <br />Apply up to max. 3 cm <br />THERMOPAL-ULTRA in one <br />application step. After sufficient standing <br />time, the surface may be grid floated or <br />rubbed down.</p> <p>6. A <br /> pply fine plaster <br />Apply THERMOPAL-FS33 cementitious <br />fine plaster using trowel techniques in the <br />required layer thickness up to max. 3 mm. <br />After drying, treat the surface with a <br />sponge rubber or a felt or sponge board.</p> <p>2</p> <p>Damp cellars, cracks in the masonry or hidden risks such as radon <br />pose a serious challenge in many buildings across Germany. <br />Professional internal cellar waterproofing with integrated radon <br />protection offers a future-proof solution: this flexible system allows <br />structural elements in contact with the ground to be reliably sealed, <br />damaged areas to be permanently repaired, whilst simultaneously <br />meeting the most stringent requirements for crack bridging.</p> <p>COMPONENTS <br />AQUAFIN-RB400 <br />ASOCRET-M30 <br />ESCO-FLUAT <br />THERMOPAL-SP <br />THERMOPAL-ULTRA <br />THERMOPAL-FS33</p> <p>Thanks to modern, mineral-based waterproofing technology, the <br />system combines high durability, vapour permeability and <br />minimal shrinkage. This ensures a safe, healthy indoor climate <br />and helps maintain the long term value of your property.</p> <p>12 <br />13</p> <p>Waterproofing | Retroactive horizontal barrier</p> <p>Retroactive horizontal barrier <br />with liquid injection material</p> <p>Application</p> <p>1</p> <p>4</p> <p>1. Level the wall surface <br />To optimise the distribution of the <br />horizontal barrier, AQUAFIN-1K is <br />applied up to approx. 10 cm above the <br />planned drilled hole depth using brush <br />techniques.</p> <p>2. F ill voids <br />Fill voids and flaws in the substrate with <br />ASOCRET-BM drilled hole material.</p> <p>3. P <br /> roduce the horizontal barrier <br />After drilling the holes (drilled hole <br />distance between 10‒12.5 cm), inject <br />AQUAFIN-F with low pressure <br />techniques (<10 bar) into the substrate <br />using injection packers. The injection <br />pressure is maintained until the area near <br />the packer appears glossy-matte. After <br />approx. 24 hours, remove the packers <br />and close the holes with ASOCRET-BM.</p> <p>4. Alternatively: <br />Pressureless Injection <br />In a pressure-free process, storage <br />containers are engaged in the drilled <br />holes and filled with the injection material. <br />The distribution in the substrate takes place <br />exclusively via gravity and the absorptive <br />behaviour of the substrate. Continue the <br />filling process until no more injection <br />medium is able to be absorbed. Similar to <br />the pressure process, the drilled holes are <br />sealed with the ASOCRET-BM or <br />ASOCRET-M30 drilled hole mortar.</p> <p>2</p> <p>3</p> <p>Rising damp in masonry is a common problem in older buildings <br />and existing properties. Retrofitting a horizontal damp proof course <br />using liquid injection material offers an effective and permanently <br />reliable solution for the restoration of damp walls and basement <br />areas. It prevents moisture from rising through the masonry by <br />capillary action, thereby providing long term protection against <br />mould growth, damage to plaster and structural deterioration. <br />The system is based on a tried-and-tested injection process: special <br />liquid active ingredients are injected precisely into the masonry via <br />boreholes. Once there, they spread evenly throughout the pore <br />structure and form a water-repellent barrier that permanently <br />prevents the capillary transport of moisture.</p> <p>COMPONENTS <br />AQUAFIN-1K <br />ASOCRET-BM <br />ASOCRET-M30 <br />AQUAFIN-F</p> <p>14 <br />15</p> <p>Waterproofing | Retroactive horizontal barrier</p> <p>Retroactive horizontal barrier <br />with paste injection material</p> <p>Application <br />1. Drill holes <br />Create drilled holes at a distance of <br />approx. 12.5 cm and a drill angle of <br />0° — 45° with an electro-pneumatic drill <br />that operates as shudder-free as possible.</p> <p>Rising damp in masonry is a common cause of damage in existing <br />buildings – ranging from damp walls and flaking plaster to mould <br />growth. Retrofitting a horizontal damp-proof course using a <br />paste-like injection material offers a modern, efficient solution for <br />permanent protection against capillary rising damp – without the <br />need for major alterations to the building structure. <br />Thanks to its creamy consistency, it can also be used for <br />horizontal drilling and where the masonry is non-uniform. There is <br />no risk of uncontrolled runoff, as is the case with water-based <br />horizontal waterproofing.</p> <p>COMPONENTS <br />AQUAFIN-i380 <br />ASOCRET-BM <br />ASOCRET-M30</p> <p>2. C <br /> lean drilled holes <br />Prior to injection, dust from drilling must be <br />removed thoroughly to ensure maximum <br />possible absorption of the active <br />substance in the masonry work.</p> <p>3. Produce the horizontal barrier <br />After cleaning the drilled holes, <br />AQUAFIN-i380 is injected using an <br />injection pistol without any pressure. <br />Material must be pressed in until the <br />drilled hole is filled completely. After <br />successful horizontal waterproofing, <br />drilled holes are sealed using <br />ASOCRET-BM or ASOCRET-M30 <br />drilled hole and void filling mortar in <br />accordance with the structure.</p> <p>16 <br />17</p> <p>Waterproofing | Salt-loaded substrates</p> <p>Renovation of salt-loaded substrates <br />in the THERMOPAL® system</p> <p>Application</p> <p>3</p> <p>2</p> <p>5</p> <p>1. Salt-loaded surface <br />The salts present in the masonry work <br />have a hygroscopic effect and migrate to <br />the surface, since less moisture is present <br />there due to the evaporation zone and <br />good conditions for crystal formation are <br />available there. This causes the plaster <br />surface to decay.</p> <p>2. A <br /> pply salt converter <br />Saturate the exposed masonry work with <br />ESCO-FLUAT one or two times using <br />brush techniques (depending on the salt <br />loading and absorbency of the substrate). <br />Salts that damage the building are <br />transformed into salts that are less soluble <br />and cannot be transmitted to the new, <br />fresh plaster layer.</p> <p>3. Apply splatterdash coat <br />Apply THERMOPAL-SP drying mortar <br />as semi-covering plaster primer <br />preparation in accordance with plastering <br />technique standards (approx. 50% surface <br />wetting) featuring a layer thickness of <br />max. 5 mm. Pre-wet the substrate lightly as <br />required to ensure good bonding.</p> <p>4. Apply base plaster <br />In case of larger surface irregularities, <br />THERMOPAL-GP11 is applied in layer <br />thickness from 10 – 30 mm (in multiple <br />layers in case of thicker surfaces). Strike <br />off the previous layer with a plasterer’s <br />darby, and immediately after stiffening, <br />roughen up horizontally and allow to dry.</p> <p>5. Apply restoration plaster <br />Apply up to max. 3 cm <br />THERMOPAL-ULTRA-white in one <br />application step. After sufficient standing <br />time, the surface may be grid floated or <br />rubbed down.</p> <p>6. A <br /> pply fine plaster (optional) <br />Apply THERMOPAL-FS33 cementitious <br />fine plaster using trowel techniques in the <br />required layer thickness up to max. 3 mm. <br />After drying, remove the surface with a <br />sponge rubber or a felt or sponge board.</p> <p>1</p> <p>Moisture and salt-loaded substrates frequently occur in legacy <br />buildings. For professional and enduring restoration of these <br />surfaces, the existing salt loading must be analysed exactly to ensure <br />that the right product systems can be used. The THERMOPAL <br />system developed for this is not only suitable for surfaces like this, it <br />also supports renovation of formerly mould-contaminated surfaces at <br />the same time. Legacy buildings become completely restored <br />structures.</p> <p>COMPONENTS <br />ESCO-FLUAT <br />THERMOPAL-SP <br />THERMOPAL-GP11 <br />THERMOPAL-ULTRA-white <br />THERMOPAL-FS33</p> <p>18 <br />19</p> <p>Waterproofing | Renovation with insulating effect</p> <p>The renovation system <br />with an insulating effect <br />For areas exposed to moisture</p> <p>The renovation system with thermal insulation properties has been <br />specially developed for masonry affected by damp and salt and <br />enables the sustainable renovation of living spaces, cellars and <br />high-quality usable areas. At its heart is an intelligent combination of <br />waterproofing, renovation plaster and mineral-based thermal <br />insulation plaster. This allows damp damage to be reliably rectified <br />whilst simultaneously reducing heat loss. <br />The insulation-effect renovation system is ideal for improving the <br />energy efficiency of older buildings, renovating listed buildings, <br />and for all buildings where external waterproofing is only possible <br />to a limited extent.</p> <p>Application</p> <p>1. Substrate preparation <br />In the first stage, the existing render is <br />removed at least 80 cm beyond the <br />damaged area in order to identify any <br />concealed moisture and salt damage. <br />Next, brittle and salt-damaged joints are <br />scraped out to a depth of approximately 20 <br />mm. The exposed, damp masonry is <br />pre-treated with AQUAFIN-Primer. <br />Joints and defects are levelled with <br />ASOCRET-M30. In addition, the existing <br />horizontal damp-proof course is sealed and <br />a barrier groove is created at the wall-floor <br />junction. Finally, a sealing groove is formed <br />at the floor/wall junction using <br />ASOCRET-M30.</p> <p>2. P <br /> roducing the horizontal <br />damp proof barrier <br />In the second step, a retrofitted horizontal <br />damp-proof course is created using <br />AQUAFIN-i380 to prevent capillary <br />rising damp. The boreholes required for <br />this are professionally sealed with <br />ASOCRET-M30 after the injection.</p> <p>4. Salt storage (if required) <br />If necessary, an additional salt storage <br />layer of THERMOPAL-ULTRA-white <br />is applied to a thickness of approx. 15 <br />mm. This layer is also combed <br />horizontally whilst still fresh, using a 6-mm <br />notched trowel.</p> <p>5. Thermal insulating plaster <br />Finally, the wall surfaces are plastered with <br />the thermal insulation plaster <br />THERMOPAL-WSP-120. Once dry, a <br />coat of AQUAFIN-Primer is applied. <br />The finishing touch is a two-coat application <br />of fine-textured plaster using <br />THERMOPAL-FS33, which ensures a <br />smooth and high-quality finish.</p> <p>3. Interior waterproofing <br />To waterproof the interior, a waterproofing <br />plaster coat of ASOCRET-M30 is <br />applied, whilst levelling the surface at the <br />same time. The coat, whilst still fresh, is then <br />combed horizontally using a 6-mm <br />notched trowel to ensure optimum <br />adhesion of the subsequent layers.</p> <p>COMPONENTS <br />AQUAFIN-Primer <br />ASOCRET-M30 <br />AQUAFIN-i380 <br />THERMOPAL-ULTRA-white <br />THERMOPAL-WSP-120 <br />THERMOPAL-FS33</p> <p>20 <br />21</p> <p>Waterproofing | Sustainable building renovation</p> <p>The system for sustainable <br />building renovation <br />Without additional waterproofing measures</p> <p>Application <br />1. Substrate preparation <br />The first step is to remove the old plaster completely in <br />order to expose damaged and contaminated areas. <br />Next, crumbling and salt-contaminated joints are <br />scraped out to a depth of approximately 20 mm. Highly <br />absorbent masonry is primed with AQUAFIN-Primer <br />to improve adhesion. Finally, the joints and defects are <br />levelled using THERMOPAL-GP11 to create a level <br />and load-bearing substrate.</p> <p>2. Producing the horizontal damp proof <br />barrier <br />Where necessary, a retrofitted horizontal damp-proof <br />course is installed in the second step. This is carried out <br />using AQUAFIN-i380 or, alternatively, <br />AQUAFIN-F, to prevent capillary rising damp. The <br />drill holes required for this are professionally sealed <br />with ASOCRET-M30 once the injection has been <br />completed.</p> <p>The system for sustainable building refurbishment offers a <br />comprehensive, tried-and-tested solution for the refurbishment of <br />existing buildings – from damp-damaged older properties to listed <br />buildings. Thanks to perfectly coordinated system components, <br />damp damage can be permanently rectified, mould growth <br />reduced and, at the same time, energy efficiency significantly <br />improved. <br />The focus is on high-performance waterproofing, renovation and <br />insulation technologies that do not require additional waterproofing <br />measures and can be used both indoors and outdoors.</p> <p>COMPONENTS <br />AQUAFIN-i380 <br />AQUAFIN-F <br />ASOCRET-M30 <br />THERMOPAL-SP <br />THERMOPAL-GP11 <br />THERMOPAL-FS33 <br />THERMOPAL-WSP-120</p> <p>3. Thermally insulating plaster <br />In the third stage, a semi-opaque spray coat of <br />THERMOPAL-SP is first applied to the sound substrate <br />to improve adhesion. The wall surfaces are then plastered <br />with the thermal insulation plaster <br />THERMOPAL-WSP-120. Once sufficiently dry, the <br />surface is primed with AQUAFIN-Primer and then <br />smoothed and finished using the THERMOPAL-FS33 <br />fine-finish trowel in two work steps.</p> <p>22 <br />23</p> <p>Waterproofing | Floor renovation</p> <p>Application</p> <p>Crack-bridging <br />floor renovation system</p> <p>2. Wall/floor connection</p> <p>3. Rolling out</p> <p>Apply the RD-SK50 self-adhesive edge <br />insulation strip in advance at the wall/floor <br />junction and to rising structural elements. If <br />there is no floor/wall junction, create the <br />waterproofing layer in advance.</p> <p>Cut the ASO-RSG to the required length. <br />Place the fabric strips onto the prepared <br />substrate with the printed side facing <br />upwards. Leave a gap of approx. 3 cm <br />around rising structural elements.</p> <p>4. Laying</p> <p>5. Coating and bedding in</p> <p>6. Sanding</p> <p>Overlap the ASO-RSG track joints by at <br />least approx. 20 mm.</p> <p>Coat the surface with <br />ASODUR-SG3-thix. The coating can <br />be applied evenly using a rubber <br />squeegee and a nylon roller. Then roll over <br />the surface again to level it out.</p> <p>Evenly sand the freshly applied layer <br />of ASODUR-SG3-thix with an excess <br />of fire-dried quartz sand (0.5–1.0 mm).</p> <p>7. Installation of the wearing layer</p> <p>De-air the fresh self-levelling compound <br />using a spiked roller immediately after <br />application. For additional surface <br />protection, we recommend finishing the <br />cured surface with ASODUR-V360W <br />in the desired colour.</p> <p>1.Substrate preperation <br />Remove any loose particles by <br />diamond grinding or shot blasting. Ensure <br />the substrate is free of dust by vacuuming.</p> <p>1</p> <p>The ground remediation system offers a cost-effective and time-saving solution for the remediation of damaged ground surfaces. <br />Rather than resorting to costly individual measures to address cracks, <br />the system enables the load-bearing capacity to be restored <br />comprehensively, whilst at the same time ensuring the long-term <br />stabilisation of the subsoil.</p> <p>2</p> <p>3</p> <p>COMPONENTS <br />ASO-RSG <br />AQUAFIN-SG3-thix <br />Quarzsand <br />ASOCRET-HFF</p> <p>After approx. 12 hours, remove all excess <br />quartz sand by sweeping and <br />vacuuming. Then finish the surface with <br />the mineral-based industrial floor <br />ASOCRET-HFF. <br />24</p> <p>25</p> <p>Waterproofing | Ground-level installation</p> <p>Application</p> <p>Waterproofing of ground-level <br />installation solutions <br />Double-facade masonry work, without basement <br />3 <br />8</p> <p>1. Wall-base slab connection <br />waterproofing <br />The first application step is to apply <br />waterproofing with AQUAFIN-RB400 <br />until up to the front side of the concrete <br />base slab.</p> <p>2. I nstall ASO-Joint-Tape-2000-S <br />While the first application step with <br />AQUAFIN-RB400 is still wet, <br />ASO-Joint-Tape-2000-S is installed <br />at an angle free of voids. Joint adhesion <br />is always applied with an overlap of <br />5-10 cm.</p> <p>3. Installation in wall edge <br />insulation strips <br />Next, the wall edge insulation strip is <br />installed or fastened in the area of the <br />window soffit using AQUAFIN-RB400.</p> <p>4. Ground-level element <br />assembly <br />Installation and stabilisation of the <br />ground-level element is completed in <br />accordance with the manufacturer’s <br />instructions.</p> <p>5. Horizontal feature <br />waterproofing <br />Fasten ASO-Connector-Joint-Tape <br />after removing the separating strip by <br />pressing on the installation element and the <br />insulation strip. The joint tape is adhered to <br />the substrate using AQUAFIN-RB400.</p> <p>6. V <br /> ertical feature <br />waterproofing <br />ASO-Connector-Joint-Tape is fastened on <br />the installation element as described in <br />step 5. The joint tape is also adhered to <br />the substrate using AQUAFIN-RB400.</p> <p>7. Protection against back <br />floating possibility <br />In order to avoid back floating possibility, <br />the area of the previously completed joint <br />tape application and the corner of the <br />insulation strip are secured by installing <br />ASO-Joint-Tape-2000-S-Corner. <br />AQUAFIN-RB400 is used for adhesion.</p> <p>8. Installation in waterproofing <br />After installation of feature waterproofing, <br />joint sealing tapes in the area of the base <br />waterproofing are coated in two layers <br />with AQUAFIN-RB400.</p> <p>9. Completely applied <br />wall structure <br />After completely drying the base <br />waterproofing, the insulation and facing <br />structure is completed.</p> <p>6</p> <p>9</p> <p>5</p> <p>4</p> <p>1</p> <p>The waterproofing of floor-to-ceiling windows and door units is <br />one of the most challenging aspects of modern building <br />construction – particularly in the case of double-skin masonry <br />and complex interfaces between different trades. <br />Where high standards of building waterproofing and energy <br />efficiency are required, reliable detailing is essential. The system <br />combines highly elastic sealing tapes with a high-performance, <br />mineral-based waterproofing layer, thereby ensuring a permanent watertight connection at points where materials <br />change and in critical connection areas.</p> <p>COMPONENTS <br />AQUAFIN-Primer <br />AQUAFIN-RB400 <br />ASO-Dichtband-2000-S <br />ASO-Dichtband-2000-S-Ecken <br />ASO-Anschlussdichtband</p> <p>26 <br />27</p> <p>Waterproofing | Garage repairs</p> <p>Application</p> <p>Garage repairs <br />with the ASO® restoration system <br />1. Level out damaged areas</p> <p>2. E dging strips <br />Apply the RD-SK50 edging strips in the <br />wall-floor transition. The substrate is <br />bonded using a self-adhering foil. After <br />fixing, RD-SK50 presses onto the wall so <br />that straining and acoustic bridges may <br />be prevented.</p> <p>3. Applying primer</p> <p>4. Quartz sand <br />If primed in advance with ASODUR-SG2, <br />the surface must be evenly sanded with <br />suitable quartz sand. After hardening, <br />remove loose quartz sand by vacuuming. <br />This entire step is not necessary when <br />priming with AQUAFIN-Primer.</p> <p>5. Level the surface <br />Mix ASOCRET-HFF self-levelling floor <br />levelling compound with the specified <br />quantity of water and apply in a single <br />application step on the primed substrate to <br />max. 35 mm. When selecting the primer, <br />please observe the currently applicable <br />technical data sheet!</p> <p>6. C <br /> reate the coved fillet</p> <p>7. Prime the levelling layer <br />Apply the respective ASODUR primer <br />to the open-pored substrate crosswise, <br />filling the pores evenly using rolling <br />techniques.</p> <p>8a. A <br /> pply coating</p> <p>8b. Applying sealing</p> <p>In case of heavy exposure, <br />ASODUR-B351 is applied evenly in a <br />single application step with a rake and <br />ventilated with a spiked roller in a criss-cross <br />manner. Optionally apply non-slip sealing; <br />for this purpose seal the hardened coating in <br />a single application step with a mixture of <br />ASODUR-V2260 and 10 wt.% <br />ASO-Antislide using a rolling technique.</p> <p>For light to moderate exposure, <br />ASODUR-V360W is applied in a single <br />application step by means of crosswise <br />rolling. Optionally apply non-slip sealing; for <br />this purpose seal the hardened sealing in a <br />single application step with a mixture of <br />ASODUR-V360W and 10 wt.% <br />ASO-Antislide using a rolling technique.</p> <p>Before application the substrate must be <br />mechanically prepared, either by <br />shotblasting or grinding and vacuuming. <br />Widen existing cracks, vacuum and seal <br />with ASODUR-GH-S. Close coarse <br />damaged areas with ASOCRET-M30 <br />using trowel techniques with a layer <br />thickness of 3 to 30 mm.</p> <p>6</p> <p>2</p> <p>1</p> <p>3</p> <p>7</p> <p>4</p> <p>Frequent use of the garage area places high demands on the <br />materials that are used. Because every time you drive a vehicle <br />in or out, dirt, and high quantities of rainwater in particular, are <br />also carried inside. <br />The moisture can easily penetrate into the floor via the walls and <br />cause moisture damage. In order to prevent these and other <br />damages, SCHOMBURG has develop an ideal application <br />technique with the right components. Damage that has already <br />occurred are able to be repaired and the garage area is able to <br />be repaired as best as possible.</p> <p>28</p> <p>Apply suitable primer to the open-pored <br />substrate. <br />• low exposure without moisture penetration <br />AQUAFIN Primer <br />• moderate to high exposure with moisture <br />penetration ASODUR-SG series</p> <p>8a <br />8b</p> <p>5</p> <p>Apply the created coved fillet wet in wet with <br />ASOCRET-M30 with an edge height of at <br />least 4 - 6 cm into the wet selected <br />ASODUR primer against the edging strips <br />(coved fillet stepped). After the coved fillet has <br />hardened, remove the edging strips and prime <br />the joint edges with INDU-Primer-S. The joint <br />is sealed with INDUFLEX-PU.</p> <p>COMPONENTS <br />ASOCRET-M30 <br />RD-SK50 <br />ASOCRET-HFF <br />ASODUR-B351 <br />ASODUR-V360W <br />ASODUR-V2260 <br />ASODUR-SG2 <br />AQUAFIN-Primer <br />ASO-Antislide <br />ASODUR-SG3 <br />INDUFLEX-PU <br />Quarzsand <br />ASODUR-GH-S</p> <p>29</p> <p>Waterproofing | Facade impregnation</p> <p>Facade impregnation for <br />colour deepening and prevention <br />of fouling</p> <p>Application <br />1. Cleaning <br />Clean the surfaces to be treated as <br />hydrophobic thoroughly using a highpressure cleaner with rotating jets. Fouling <br />and moss or algae coatings are removed <br />completely.</p> <p>2</p> <p>1</p> <p>Facades are a building’s calling card, but at the same time they are <br />constantly exposed to the elements, such as rain, frost, UV radiation and <br />dirt. Facade impregnation offers an effective and sustainable solution for <br />providing long-lasting protection for mineral-based external surfaces <br />against moisture and environmental influences.</p> <p>COMPONENTS <br />ASOLIN-SFC45</p> <p>2. A <br /> pply impregnation <br />After the façade has dried completely, <br />apply the solvent-free façade cream <br />ASOLIN-SFC45 with a lambskin roller <br />until it fully covers the entire surface. The <br />paste consistency makes very economical, <br />clean, and reliable application possible. <br />A material buffer remains on the substrate <br />during application, which enables very <br />deep penetration of the effective <br />substance into the substrate.</p> <p>The system is based on modern, hydrophobic impregnations that <br />penetrate deep into the substrate, where they form a water-repellent <br />protective layer. This significantly reduces capillary water absorption, <br />whilst at the same time the facade remains vapour-permeable, allowing <br />trapped moisture to escape. Facade impregnation is suitable for a wide <br />range of mineral substrates – including brick, clinker, natural stone, <br />sand-lime brick and rendered facades.</p> <p>30 <br />31</p> <p>Waterproofing | Sewage treatment works</p> <p>Waterproofing and repair of wastewater <br />treatment plants <br />Cementitious restoration concept</p> <p>Application</p> <p>4 <br />5</p> <p>1</p> <p>6</p> <p>1. Level out damaged areas <br />Repair small crack damage and voids <br />with a trowel or float. Application of <br />ASOCRET-BIS-5/40 while still wet onto <br />adhesive slurry. <br />ASOCRET-HS-flex.</p> <p>2. L evel the surface <br />Apply ASOCRET-BIS-1/6 onto the <br />prepared substrate in the desired layer <br />thickness up to 6 mm in a single <br />application step. The surface may not be <br />processed retroactively with a wide <br />brush or a wet flat trowel. <br />For smooth transitions on the repair <br />surface, a sponge may be used <br />afterwards to rub the area.</p> <p>3. Waterproof the wall-floor <br />transition <br />Apply AQUAFIN-2K/M-PLUS in the <br />transition between the wall and floor and <br />across connecting joints using brush and <br />trowel techniques and adhere <br />ASO-Joint-Tape-2000-S free of voids <br />and wrinkles. <br />Application covering the whole area <br />takes place during area waterproofing.</p> <p>4. Transition to the flange <br />structure <br />In the area of the flange structure, apply <br />ASODUR-SG3-thix special pre-primer <br />along the sanded flange structure using <br />a brushing and rolling technique. After <br />curing, apply the 2nd layer of <br />ASODUR-SG3-thix using a rolling <br />technique and scatter quartz sand <br />0.5–1.0 mm on the primer while still fresh.</p> <p>5. Quartz sand <br />After curing, apply the 2nd layer of <br />ASODUR-SG3-thix using a rolling <br />technique and scatter quartz sand <br />0.5–1.0 mm on the primer while still fresh.</p> <p>6. W <br /> aterproof surfaces <br />Apply AQUAFIN-2K/M-PLUS in a <br />minimum of two application steps using <br />spray, brush, or trowel techniques.</p> <p>3 <br />2</p> <p>Sewage treatment works are among the most technically <br />demanding infrastructure projects. They are constantly exposed <br />to sewage, service water and rainwater, as well as fluctuating <br />chemical influences. These stresses frequently lead to damage <br />such as cracking, spalling, moisture penetration or blistering <br />caused by osmotic pressure. <br />The system provides targeted protection for the affected areas <br />using highly durable waterproofing membranes, specialist <br />primers and repair mortars that perform reliably even under <br />demanding operating conditions.</p> <p>COMPONENTS <br />ASOCRET-HS-flex <br />ASOCRET-BIS-5/40 <br />ASOCRET-BIS-1/6 <br />AQUAFIN-2K/M-PLUS <br />ASO-Dichtband-2000-S <br />ASODUR-SG3-thix <br />Quarzsand</p> <p>32 <br />33</p> <p>Waterproofing | Service water containers</p> <p>Waterproofing and repair of process <br />water containers <br />Cementitious restoration concept</p> <p>2 <br />4 <br />1</p> <p>Service water tanks used in industry, agriculture and the <br />commercial sector must meet the highest standards of <br />watertightness, durability and hygiene. The system solution for <br />service water tanks offers a safe and long-lasting solution for <br />waterproofing and repairing concrete tanks, which can withstand <br />a wide range of water qualities and stresses over the long term. <br />Depending on the application, the system provides targeted <br />protection for concrete surfaces using high-quality <br />waterproofing, repair mortar and carefully selected system <br />components, ensuring reliable performance even under <br />demanding conditions.</p> <p>5</p> <p>Application</p> <p>1. Crack restoration <br />Assess and seal cracks professionally <br />(see the chapter on crack restoration).</p> <p>2. L evel out damaged areas <br />Close damaged areas and voids with <br />ASOCRET-BIS-5/40 using trowel <br />techniques. Application is completed while <br />still wet onto the ASOCRET-HS-flex <br />adhesive slurry.</p> <p>4. + 5. Waterproof the wall-floor <br />transition <br />Apply AQUAFIN-RB400 in the <br />transition between the wall and floor and <br />across connecting joints using brush and <br />trowel techniques and adhere <br />ASO-Joint-Tape-2000-S free of <br />voids and wrinkles. <br />Application covering the whole area <br />takes place during area waterproofing.</p> <p>6. W <br /> aterproof surfaces <br />Apply AQUAFIN-RB400 in a minimum <br />of two application steps using spray, <br />brush, or trowel techniques.</p> <p>3. Level the surface <br />Apply ASOCRET-BIS-1/6 onto the <br />prepared substrate in the desired layer <br />thickness up to 6 mm in a single <br />application step and processed <br />retroactively using a felt or sponge board.</p> <p>6</p> <p>3</p> <p>COMPONENTS <br />ASOCRET-HS-flex <br />ASOCRET-BIS-5/40 <br />ASOCRET-BIS-1/6 <br />AQUAFIN-RB400 <br />ASO-Dichtband-2000-S</p> <p>34 <br />35</p> <p>Waterproofing | Protection of reinforced concrete</p> <p>Reinforced concrete protects container <br />construction against chemical and <br />mechanical degradation</p> <p>Application</p> <p>4</p> <p>2</p> <p>5</p> <p>6</p> <p>1. Crack restoration <br />Static or water-conducting cracks in the <br />concrete must be sealed professionally <br />(refer to the chapter “Crack restoration”).</p> <p>2. L evel the surface <br />Apply ASOCRET-BIS-1/6 in a single <br />application step up to 6 mm layer <br />thickness on the surface. Application is <br />completed while still wet onto the <br />ASOCRET-HS-flex adhesive slurry.</p> <p>3. Create the coved fillet <br />Create a sealing groove in the wall-floor <br />transition using ASODUR-SG3 and <br />quartz sand 0.06 - 1.50 mm in a mix ratio <br />of 3:25 GT. The sealing fillet must be laid <br />while still wet onto the previously applied <br />primer layer of ASODUR-SG3.</p> <p>4. Transition to the flange <br />structure <br />In the area of the flange structure, apply <br />ASODUR-SG3-thix special pre-primer <br />free of pores over the flange structure with <br />a short-pile wool roller and spread with <br />rough quartz sand immediately. After <br />sufficient curing, further waterproofing <br />measures may be applied.</p> <p>5. Applying primer <br />Wall: Roll ASODUR-SG3-thix on first <br />equally with a short-pile wool roller, then <br />brush it into the surface zone carefully <br />using a priming brush and then rework it <br />again with the wool roller.</p> <p>6. S <br /> urface protection <br />Apply ASODUR-V2370 by rolling or <br />spraying of a minimum of least two coats. <br />The overcoating time depends on the <br />temperature. Please read the technical data <br />sheet.</p> <p>1 <br />3</p> <p>The protection of reinforced concrete components is essential <br />for durability and longevity. Particularly with load-bearing <br />building components such as foundations and pillars, inadequate <br />protection of surfaces and joints can result in significant damage <br />to the structure. Due to high mechanical loads and strong <br />chemical corrosion, the functionality and service life of containers, <br />pools and gutter systems are severely restricted and shortened. <br />In individual cases, the destructive influence is so great that a <br />reduction in the concrete on the surface can be seen after just a <br />few years. Then it is important to carry out the right refurbishment <br />measures at an early stage. The SCHOMBURG system products <br />provide targeted protection against aggressive influences.</p> <p>COMPONENTS <br />AQUAFIN-P1/-P4 <br />ASOCRET-HS-flex <br />ASOCRET-BIS-1/6 <br />ASOCRET-BIS-5/40 <br />ASODUR-SG3 <br />ASODUR-SG3-thix <br />ASODUR-V2370</p> <p>Floor: Apply ASODUR-SG3-thix in <br />dollops using a rubber lipped scraper, <br />brush it in thoroughly, and roll it out <br />afterwards.</p> <p>36 <br />37</p> <p>Waterproofing | Vapour barrier for damp substrates</p> <p>Vapour barrier for damp substrates <br />in the epoxy resin system</p> <p>Application</p> <p>5</p> <p>2</p> <p>3</p> <p>4</p> <p>1</p> <p>Damp substrates and high residual moisture levels are a common <br />challenge in the construction industry and can lead to significant <br />damage or delays to building works. The vapour barrier for <br />damp substrates offers a reliable solution for permanently <br />blocking rising damp and safely protecting sensitive floor <br />coverings. <br />The system is based on high-performance two-component <br />epoxy resin barrier primers, which have been specially developed for damp substrates. They act as a capillary-breaking <br />and diffusion-inhibiting layer, preventing the penetration of <br />moisture from the substrate and providing reliable protection <br />against damage such as osmosis blisters, delamination or <br />deformation of floor coverings such as parquet, natural stone or <br />vinyl flooring. <br />38</p> <p>COMPONENTS <br />ASODUR-SG2 <br />ASODUR-SG3</p> <p>1. Substrate preparation <br />Substrates must be load-bearing and <br />sufficiently firm (concrete class: min. <br />C 20/25 and cement-based screed class <br />min. CT–C35–F5), and free of separating <br />and adhesion-inhibiting substances like <br />paint residues. Depending on the texture <br />of the substrate to be treated, suitable <br />processes must be used, e.g. grinding.</p> <p>2. C <br /> leaning preparations <br />The dust particles resulting from this <br />measure that is taken to prepare the <br />substrate should generally be removed <br />using an industrial vacuum.</p> <p>4. Rolling on <br />To ensure equal material film on the <br />substrate surface, a suitable lamb’s wool <br />roll should be used to roll the still wet <br />applied material out again equally.</p> <p>5. Sanding <br />Immediately after applying the material, <br />the wet applied primer layer, and only in <br />case of ASODUR-SG2, should be <br />sanded equally using suitable quartz <br />sand. ASODUR-SG3 does not need to <br />be sanded because a chemical bond <br />results. After hardening, remove loose <br />quartz sand by vacuuming.</p> <p>3. Material application <br />The correctly mixed 2-component material <br />is applied using a rubber lipped scraper <br />on the pre-wetted substrate (matte damp <br />appearance) and intensively brushed in <br />using scrub brushes.</p> <p>39</p> <p>Waterproofing | Crack repair of substrates</p> <p>Crack repair of substrates <br />in the epoxy resin system</p> <p>Application</p> <p>7</p> <p>6</p> <p>5</p> <p>1. Open the cracks <br />Open the crack or joint with a cutting disc <br />along the length (approx. up to half or <br />two thirds of the screed depth). Cut <br />traverse sections featuring a depth of 10 <br />cm length at a right angle at a distance of <br />30 cm.</p> <p>2. Clean <br />Remove dust and dirt and carefully clean <br />the area that has been cut open with an <br />industrial vacuum cleaner or similar <br />equipment.</p> <p>3. Mixing <br />Mix the A and B components together and <br />shake for a minimum of 15 seconds.</p> <p>4. Insert screed clamps <br />Insert the included screed clamps into the <br />cut groove.</p> <p>5. Cast the cracks <br />Pour the mixed ASODUR-GH-S material <br />into the prepared grooves free of voids. <br />Remove the excess material.</p> <p>6. Q <br /> uartz sand <br />After reaching the gel phase, evenly <br />sprinkle in quartz sand (grain size <br />0.1 to 0.6 mm).</p> <p>7. Vacuuming <br />After hardening, remove loose sand by <br />vacuuming.</p> <p>Alternatively <br />For fine cracks up to a width of 0.4 mm, <br />use the epoxy resin grout <br />ASODUR-K900.</p> <p>4</p> <p>1</p> <p>Cracks in screed and concrete surfaces are not merely aesthetic <br />flaws; they can also significantly compromise the load-bearing <br />capacity and durability of structures. Crack repair offers a <br />professional, systematic solution for permanently sealing cracks <br />and reliably restoring the structural integrity of substrates. <br />The system is based on high-performance two-component reactive <br />resins with excellent penetration properties, which completely fill <br />even fine and deep cracks. Targeted grouting and additional <br />bonding using screed clips create a force-locked connection <br />between the crack flanks, ensuring that compressive, tensile and <br />shear forces are once again safely transferred.</p> <p>COMPONENTS <br />ASODUR-GH-S <br />ASODUR-K900 <br />Quarzsand</p> <p>40 <br />41</p> <p>Waterproofing | Crack repair on wall surfaces</p> <p>Waterproofing of wall surfaces <br />with crack injection</p> <p>Application</p> <p>3</p> <p>1 <br />5</p> <p>1. Drilling <br />Cracks that are present are offset at a <br />respective distance of 20 cm at an angle <br />of 45° to the crack.</p> <p>2. C leaning <br />Clear any drilling debris that has resulted <br />in the drilled holes using oil-free <br />compressed air.</p> <p>3. Waterproof water-conducting <br />cracks <br />Insert corresponding injection packer into <br />the drilled holes. Press AQUAFIN-P1 <br />into water-conducting cracks. The material <br />reacts with the water to produce <br />a waterproof, tough elastic foam to stop <br />water penetration. The excess foam is <br />removed after curing so it is flush with the <br />surface.</p> <p>4. Dam up cracks <br />In case of cracks that do not conduct <br />water, the crack area is insulated using <br />ASODUR-EKF. AQUAFIN-P4 is <br />injected after the insulating material cures <br />completely.</p> <p>5. Permanently waterproof <br />cracks <br />During application of AQUAFIN-P1, <br />additional injection using AQUAFIN-P4 <br />elastic crack waterproofing is necessary.</p> <p>6. S <br /> eal drilled holes <br />After the injection resin has hardened, <br />insulation may be removed for visual <br />reasons as required. Seal the drilled holes <br />with ASOCRET-BIS-1/6.</p> <p>6</p> <p>4</p> <p>Professional crack repair is essential in building renovation and <br />refurbishment. Cracks occur when the stresses acting on the <br />substrate exceed the strength of the individual structural elements. <br />Whether in basements, underground car parks or on load-bearing <br />structures – water ingress can cause lasting damage to the <br />building fabric and significantly restrict the use of buildings.</p> <p>COMPONENTS <br />AQUAFIN-P1 <br />AQUAFIN-P4 <br />ASODUR-EKF <br />ASOCRET-BIS-1/6</p> <p>Professional injection methods offer a reliable and long-lasting <br />solution here: through targeted crack injection using highly effective <br />injection resins, even active, water-bearing cracks are securely <br />sealed and the structural integrity of the building is restored.</p> <p>42 <br />43</p> <p>Waterproofing | Retrospective execution of construction joints</p> <p>Application</p> <p>Retrospective execution of construction/ <br />movement joints in concrete construction <br />With thermoplastic joint tape <br />1. Substrate preparation <br />Prepare the cleaned, load-bearing <br />substrate by mechanical means. <br />Substrates must be load-bearing and <br />sufficiently firm (concrete class: min. <br />C 20/25 and cement-based screed class <br />min. CT–C35–F5), and free of separating <br />and adhesion-inhibiting substances like <br />paint residues.</p> <p>2. C <br /> leaning preparations <br />The dust particles resulting from this <br />measure that is taken to prepare the <br />substrate should generally be removed <br />using an industrial vacuum.</p> <p>3. M <br /> asking the surface <br />Mask off the expansion area on the <br />substrate and on the tape. Mask off at the <br />margin, the mortar should overlap the <br />building component by at least 1 cm.</p> <p>4. Applying adhesive</p> <p>5. Peeling off the adhesive tape <br />Remove the adhesive tape in the area of <br />the joint.</p> <p>6. Inserting and pressing on <br />Lay out the ASO-Tape and press it on <br />with a suitable tool.</p> <p>8. Bonding <br />Ensure that there is an overlap of 5–10 cm <br />with a minimum film thickness of 1 mm <br />when bonding the ASO-Tape to the <br />mortar.</p> <p>9. Hot air welding <br />Using hot air and pressure, weld the tape <br />joins with an overlap of at least 5 cm.</p> <p>Stir comp. A and comp. B together and <br />decant the mixture into a clean container. <br />Then stir the mixture for a second time. <br />In order to ensure bedding covering the <br />whole area, apply ASODUR-K4031 at <br />least 1 cm wider than the amount of <br />ASO-Tape you use.</p> <p>Leaking joints, transitions and penetrations are among the most <br />common causes of moisture damage in buildings. A permanently <br />reliable waterproofing solution is therefore crucial to ensure the <br />watertightness and functionality of concrete structures in the long <br />term. <br />The thermoplastic joint tape can be used to reliably seal <br />construction joints, movement joints, cracks and defects. The <br />system is watertight – even under negative water pressure – <br />and provides a permanently secure bond for demanding <br />waterproofing tasks.</p> <p>COMPONENTS <br />ASO-Tape <br />ASODUR-K4031</p> <p>7. Grouting and peeling off <br />Ensure the ASODUR-K4031 is spread <br />over all of the ASO-Tape. Remove all <br />adhesive strips.</p> <p>44 <br />45</p> <p>Waterproofing | Execution of construction joints in concrete construction</p> <p>Execution of construction joints in concrete <br />construction with crystalline waterstop sheet</p> <p>Construction joints are among the most critical areas of concrete <br />structures and pose an increased risk of water ingress. Crystalline joint <br />sheets can be used to seal construction joints reliably and <br />permanently. The coated joint sheet extends the water path, ensures a <br />strong bond with the waterproof concrete and thus minimises the risk <br />of leaks.</p> <p>COMPONENTS <br />AQUAFIN-CJ5 <br />Retaining clips <br />Omega-Holder</p> <p>Application / effect</p> <p>Fastening with omega clips <br />The crystalline waterstop sheet <br />AQUAFIN-CJ5 is placed on the <br />reinforcement with the omega clip in the <br />middle of the joint. The omega clip is <br />attached to the reinforcement with tie wire. <br />A concrete inclusion of > 3 cm must be <br />ensured.</p> <p>Jointing of waterstop sheets <br />With AQUAFIN-CJ5, secure overlap <br />joints with retaining clips. For immersion <br />depths of up to 8 m, fix in place with a <br />holding clip with an overlap of 5 cm. For <br />immersion depths of 8 to 20 m, fix in <br />place with two holding clips with an <br />overlap of 20 cm.</p> <p>Construction joint wall / slab <br />bonding <br />A transition from the working joint in the <br />wall / floor transition to a vertical working <br />joint is made using two holding clips that <br />are attached on both sides. <br />The overlapping of the waterstop sheet is <br />a minimum of 5 cm.</p> <p>Secure sealing with AQUAFIN-CJ5 <br />The cementitious coating forms a strong <br />adhesive bond with the waterproof <br />concrete so that “breaks” / cracks tend not <br />to occur. However, if the movement of the <br />component results in a crack, crystals form <br />and cracks up to 0.4 mm can be sealed in <br />the event of contact with water</p> <p>Corner solutions <br />In corners, the waterstop sheet <br />AQUAFIN-CJ5 is simply bent into the <br />required shape.</p> <p>The crystalline coating offers additional protection: upon contact with <br />water, crystals form which can seal cracks up to 0.4 mm wide, thereby <br />providing long-lasting support for the sealing effect.</p> <p>46 <br />47</p> <p>Waterproofing | Execution of construction joints in concrete construction</p> <p>Application</p> <p>Execution of construction joints in concrete <br />construction with injection hose system <br />1. Standard packer <br />Nail a standard packer at the start and <br />end point (max. 10 m) on the inside of the <br />formwork.</p> <p>2. Fasten the injection hose <br />Fasten the AQUAFIN-CJ1 injection <br />hose carefully with the help of the hose <br />clamp on the packer.</p> <p>3. Lay out the injection hose <br />Lay the injection hose featuring a concrete <br />covering of at least 8 cm to the waterconducting side and then fasten it with <br />holding clips (6 per m) onto the concrete to <br />prevent slipping or floating upwards.</p> <p>4. Adhere ventilation hose <br />Apply the included PVC adhesive on the <br />projecting connection collar of the <br />ventilation hose.</p> <p>5. Connect the injection hose <br />Attach the AQUAFIN-CJ1 injection <br />hose directly onto the prepared <br />connection collar, and then wait for the <br />drying time to finish.</p> <p>6. C <br /> onnect the ventilation hose <br />completely <br />Pull approx. 6–8 cm heat-shrink hose over <br />the connection of the ventilation hose and <br />the injection hose and use hot air to heat <br />up the connection until the heat-shrink <br />hose is tight and the connection has <br />tightened.</p> <p>1</p> <p>7</p> <p>3</p> <p>The professional sealing of construction joints in concrete structures <br />is crucial to the durability and watertightness of buildings. Modern <br />injection hose systems offer a reliable and flexible solution for <br />permanent sealing joints in so-called ‘white tanks’ against water <br />and moisture. <br />In concrete structures, construction phases inevitably result in joints <br />which must be specifically sealed. The installation of a PVC <br />injection tube enables controlled, retrofit waterproofing directly <br />within the joint area. Through the targeted injection of sealant resins, <br />even the smallest defects are reliably sealed, as the material <br />spreads throughout the entire joint area and effectively waterproofs <br />the concrete.</p> <p>COMPONENTS <br />AQUAFIN-CJ1 <br />AQUAFIN-CJ-Set <br />AQUAFIN-P1 <br />AQUAFIN-P4</p> <p>7. C <br /> onnect the various hose <br />sections <br />Insert the hose ends of the ventilation <br />hoses into a container for safekeeping <br />and add injection nipples prior to injection <br />(e.g. with AQUAFIN-P1 and <br />AQUAFIN-P4).</p> <p>48 <br />49</p> <p>Waterproofing | Execution of construction joints in concrete construction</p> <p>Execution of construction joints in concrete <br />construction with swelling joint tape</p> <p>Application <br />100</p> <p>m <br />0m</p> <p>4</p> <p>mm</p> <p>.)</p> <p>(min</p> <p>x.)</p> <p>(ma</p> <p>25</p> <p>3</p> <p>The reliable sealing of construction joints in concrete structures is <br />a key factor in the durability and watertightness of buildings. The <br />use of elastomeric swelling joint tapes represents a tried-andtested, cost-effective solution for reliable sealing concrete joints <br />against groundwater, slope water and surface water.</p> <p>COMPONENTS</p> <p>Elastomeric swelling joint tapes are made from special plastics <br />containing reactive fillers and are characterised by their strong, <br />dimensionally stable swelling behaviour upon contact with <br />water. They can increase their volume by more than 700 per <br />cent and adapt perfectly to joint gaps without being washed out.</p> <p>As an alternative to <br />AQUAFIN-CJ6: <br />AQUAFIN-CJ3 or AQUAFIN-CJ4 <br />can also be used.</p> <p>AQUAFIN-CA <br />AQUAFIN-CJ6* <br />Fastening mesh</p> <p>1a. Adhesion using assembly <br />adhesive <br />Spray AQUAFIN-CA assembly <br />adhesive onto the cleaned substrate using <br />a hand cartridge and press in the <br />AQUAFIN-CJ6 swelling joint tape <br />covering the whole area until the <br />assembly adhesive pushes out at the <br />sides.</p> <p>1b. M <br /> echanical fastening <br />Alternatively, AQUAFIN-CJ6 can be <br />fixed with a concrete covering of at least <br />8 cm to the water-conducting side with <br />4-6 fastening points or the fixing grid. The <br />swelling joint tape must be applied <br />covering the whole area of the concrete <br />substrate.</p> <p>3. O <br /> verlapped butt joints <br />Alternatively, swelling tape connections <br />can be applied with an overlap of at least <br />50 mm. In this case, both swellable <br />waterstops should be positioned close <br />together to prevent voids.</p> <p>4. Corner connections <br />Corner connections should essentially be <br />applied with an additional safeguard.</p> <p>2. Blunt butt joints <br />Swelling tape connections can be <br />applied as blunt connections. In case of <br />larger wall profiles, secure the butt joints <br />with a separate swelling tape featuring an <br />overlap of at least 50 mm.</p> <p>50 <br />51</p> <p>Waterproofing | Concrete surface protection</p> <p>System architecture according to DIN EN 1504-2 |OS5b</p> <p>Concrete surface protection in underground <br />car parks and paved multi-storey car parks <br />Area <br />1 AQUAFIN-Primer <br /> <br />2 AQUAFIN-OS, applied in two layers <br /> <br />3 <br /> <br />Protective layer against damage <br />Dichtungskehle <br />1 AQUAFIN-PRIMER <br /> <br />4 ASOCRET-M30 <br /> <br />2 AQUAFIN-OS, <br />applied in two layers <br />2</p> <p>1 <br />4</p> <p>3</p> <p>System architecture according to <br />DIN 18533 <br />Concrete components are exposed to harmful environmental <br />factors on a daily basis. Moisture, chlorides, frost and de-icing <br />salt damage, and carbonation can attack the structural integrity <br />of the building and significantly reduce the service life of the <br />structure. <br />OS5b surface protection coatings provide reliable protection for <br />concrete surfaces. The crack-bridging coating prevents the <br />penetration of substances that damage concrete, protects the <br />reinforcement from corrosion and makes a lasting contribution to <br />maintaining the value and longevity of concrete structures.</p> <p>COMPONENTS <br />AQUAFIN-RB400 <br />AQUAFIN-OS <br />ASOCRET-M30 <br />AQUAFIN-Primer</p> <p>Fläche <br />1 AQUAFIN-PRIMER <br /> <br />2 AQUAFIN-RB400, <br /> <br /> applied in two layers <br />3 Protective layer against damage <br /> <br />Dichtungskehle <br />1 AQUAFIN-PRIMER <br /> <br />4 ASOCRET-M30 <br /> <br />2 AQUAFIN-RB400, <br />applied in two layers</p> <p>2</p> <p>1 <br />4</p> <p>3</p> <p>52 <br />53</p> <p>Waterproofing | General information for planning and execution</p> <p>AQUAFIN-1K</p> <p>Cementitious waterproofing</p> <p>AQUAFIN2K/M-PLUS</p> <p>AQUAFINRB400</p> <p>General information <br />for planning and execution</p> <p>Ground moisture and non-pressing water ( W1.1-E, W1.2-E in accordance with DIN 18533) o</p> <p>+</p> <p>+</p> <p>Pressing water (W2-E in accordance with DIN 18533)</p> <p>—</p> <p>—</p> <p>+</p> <p>Non-pressing water on earth-covered slabs (W3-E)</p> <p>+</p> <p>+</p> <p>+</p> <p>Splash water and ground moisture at the wall base (W4-E in accordance with DIN 18533) o</p> <p>+</p> <p>+</p> <p>Retroactive building waterproofing in accordance with WTA datasheet 4–6–14/D</p> <p>+</p> <p>+</p> <p>+</p> <p>Cellar interior sealing in accordance with WTA datasheet 4–6–14/D</p> <p>++</p> <p>+</p> <p>+</p> <p>Strip-shaped building waterproofing up to 0.25 mm opening width*</p> <p>—</p> <p>+</p> <p>+</p> <p>Waterproofing in and under wall upstand surfaces</p> <p>—</p> <p>+</p> <p>+</p> <p>Wall-floor transition</p> <p>o</p> <p>+</p> <p>+</p> <p>Base waterproofing transition</p> <p>++</p> <p>+</p> <p>+</p> <p>Drinking water containers</p> <p>—</p> <p>+</p> <p>—</p> <p>Service water container</p> <p>++</p> <p>+</p> <p>+</p> <p>Sewage treatment plants</p> <p>++</p> <p>+</p> <p>+</p> <p>Overflow basins</p> <p>++</p> <p>+</p> <p>+</p> <p>Water fountains, fonts</p> <p>++</p> <p>+</p> <p>+</p> <p>Building waterproofing</p> <p>The right waterproofing for any exposure <br />COMBIDIC-2KCLASSIC/ <br />PREMIUM</p> <p>Container seals – water pressing from the inside</p> <p>COMBIDIC-1K</p> <p>Bituminous waterproofing</p> <p>Ground moisture and non-pressing water ( W1.1-E, W1.2-E in accordance with DIN 18533)</p> <p>+</p> <p>+</p> <p>Pressing water (W2.1-E in accordance with DIN 18533)</p> <p>—</p> <p>+</p> <p>Bonded waterproofing in combination with tiled finishes</p> <p>Non-pressing water on earth-covered slabs (W3-E)</p> <p>—</p> <p>+</p> <p>Balconies/terraces</p> <p>—</p> <p>+</p> <p>—</p> <p>Splash water and ground moisture at the wall base (W4-E in accordance with DIN 18533)</p> <p>+</p> <p>+</p> <p>Shower areas in private buildings</p> <p>—</p> <p>+</p> <p>—</p> <p>Retroactive building waterproofing in accordance with WTA datasheet 4-6-05D</p> <p>+</p> <p>+</p> <p>Shower areas in public buildings</p> <p>—</p> <p>+</p> <p>—</p> <p>Strip-shaped building waterproofing up to 0.25 mm opening width</p> <p>—</p> <p>+</p> <p>Swimming pools</p> <p>—</p> <p>+</p> <p>—</p> <p>Fastening protective and drainage panels</p> <p>+</p> <p>+</p> <p>Swimming pool decks</p> <p>—</p> <p>+</p> <p>—</p> <p>Full-surface adhesion of perimeter insulating materials</p> <p>—</p> <p>+</p> <p>Building waterproofing</p> <p>++ suitable for substrates that are subsequently not subject to cracking <br />+ suitable</p> <p>o only suitable as protection against back floating in combination with <br />flexible cementitious waterproofing slurry</p> <p>—</p> <p>unsuitable</p> <p>* Based on building regulations list A, part 2 sequential number 1.4, a special agreement is <br />necessary between the employer/contractor</p> <p>Note: The technical datasheets for the listed products must <br />be observed.</p> <p>54 <br />55</p> <p>Waterproofing | Joint tapes</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telefon +49-5231- 953-00 <br />Telefax +49-5231- 953-333 <br />www.schomburg.de</p> <p>Technische Darstellung 1.70.5</p> <p>Eindichtung eines Dacheinlaufes in <br />einer Tiefgaragendecke</p> <p>Joint and feature waterproofing <br />with joint sealing tapes</p> <p>Special detail waterproofing solutions with joint sealing tape <br />also need to protect building components and constructions in <br />combination with the waterproofing layer against the influence <br />of chemicals or hygienically questionable substances.</p> <p>6</p> <p>5</p> <p>The reasons for damage can often be traced to the use of <br />unsuitable joint tapes or pre-formed pieces.</p> <p>3 <br />4</p> <p>2</p> <p>1</p> <p>SCHOMBURG offers a wide assortment of diverse joint tapes <br />and pre-formed pieces.</p> <p>1 Stahlbetondecke <br />2 Flachdacheinlauf, z.B. Fa. Passavant <br />3 Einlage von ASO-Dichtmanschette-Boden <br />4 Abdichtung mit AQUAFIN-RB400 oder AQUAFIN-2K/M-PLUS <br />5 Drain- und Schutzschicht <br />6 Extensive Begrünung</p> <p>The benefits of joint tape constructions in the SCHOMBURG <br />product range</p> <p>Die Rechte des Käufers in Bezug auf die Qualität unserer Materialien richtet sich nach unseren Verkaufs- und Lieferbedingungen. Bei dieser Darstellung handelt es sich <br />um eine unverbindliche Musterdarstellung. Ein Anspruch auf Vollständigkeit besteht nicht. Die Darstellung befreit den Anwender nicht von seiner Sorgfaltspflicht. Mit <br />Herausgabe einer neuen Fassung der Druckschrift verliert diese ihre Gültigkeit. <br />06/21 SF/HE/KK</p> <p>Every component features corners, edges, and intersections in <br />the form of pipes, channels, screws, and dowels that need to be <br />waterproofed. An essential aspect of protection of buildings <br />against dampness is also the integration of detail points like floor <br />drains, wall-floor transition joints, or building component joints <br />using joint tape. <br />Additionally, joint tapes need to absorb and dissipate possible <br />movements and stresses from the substrate reliably so that <br />damage cannot result.</p> <p>COMPONENTS <br />ASO-Dichtband 2000 S <br />ASO-Dichtband 2000 Ecken <br />ADF-Rohrmanschette</p> <p>Impermeability to water <br />The most important requirement of waterproofing materials, <br />impermeability to water in connection with high elasticity and <br />crack bridging, is proven to be fulfilled completely by all <br />SCHOMBURG joint tape types and pre-formed pieces.</p> <p>Connect the waterproofing material with the joint <br />sealing tape <br />SCHOMBURG joint tape guarantees very good surface <br />adhesion of the waterproofing material used with the joint <br />sealing tape. This ensures good bonding with the substrate.</p> <p>Vapour permeability <br />SCHOMBURG joint tape materials are water vapour permeable. If the waterproofing material to be used on and underneath <br />the joint tapes is applied during joint adhesion overlapped, <br />SCHOMBURG joint tape ensures reliable drying.</p> <p>Reliability due to pre-formed pieces <br />SCHOMBURG offers a wide assortment of sophisticated <br />pre-formed pieces. This increases the security of complete <br />performance and saves costs. Cutting and the possible risk <br />connected due to any resulting complaints.</p> <p>High resistance to alkalinity <br />In case alkaline water penetrates up to the waterproofing layer, <br />SCHOMBURG joint tape materials ensure that the joint tape <br />cannot delaminate or disintegrate.</p> <p>Building-related special productions <br />If connections and joint waterproofing can no longer be reliably <br />or economically completed with the standard types and <br />solutions, we recommend ASO-Joint-Tape-2000-S wide <br />products. This material enables building-related special products <br />easy to produce on the building site.</p> <p>Resistance to chemical attacks <br />Especially during production of waterproofing solutions in <br />application areas that are exposed to higher chemical stresses, <br />joint tapes also need to be resistant against the possible effects <br />of aggressive inorganic or organic substances. Corresponding <br />certificates for SCHOMBURG joint tapes are provided in our <br />documents.</p> <p>56 <br />57</p> <p>The SCHOMBURG Group develops, produces <br />and distributes building product systems for the <br />areas of:</p> <p>To meet the demanding requirements of an <br />ever-changing market, we continuously invest <br />in the research and development of new and <br />already existing products. This guarantees an <br />ever increasing product quality to the <br />satisfaction of our customers.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>16/26 31/26 NT/IsW/KK</p> <p>Experts value the quality and the efficiency <br />of building product systems, the services and <br />therefore the core competence of the group <br />of companies.</p> <p>2D1070230</p> <p>For over 85 years SCHOMBURG’s <br />development competence has been recognised <br />in both the domestic and the worldwide <br />marketplace. Building product systems that are <br />produced in-house are highly prized around the <br />world.</p> <p>Subject to change. The valid issue of the corresponding technical bulletin legally applies.</p> <p>• Waterproofing and repair of buildings <br />• Tiles/natural stone/screed application <br />• Ground protection/floor coating systems</p>
