AQUAFIN-CJ6_abP_gem_VVTB_C3.30_GB.pdf
12 Страницы
1013,0 КБ
Download
<h1>AQUAFIN-CJ6_abP_gem_VVTB_C3.30_GB.pdf</h1> <p>General Building Code Test Certificate <br />- Translation -</p> <p>Test Certificate No.:</p> <p>P-5196/307/09 MPA-BS</p> <p>Test item:</p> <p>AQUAFIN-CJ6 swellable joint sealing tape <br />for internal joint sealing in concrete members with a high water <br />penetration resistance against pressing and non-pressing <br />water and against ground moisture in compliance with the <br />Administrative Provisions – Technical Building Rules <br />sequential no. C 3.30</p> <p>Client:</p> <p>SCHOMBURG GmbH & Co.KG <br />Aquafinstraße 2 - 8 <br />D-32760 Detmold</p> <p>Date when first issued:</p> <p>09/03/2010</p> <p>Issued on:</p> <p>09/03/2025</p> <p>Valid until:</p> <p>08/03/2030</p> <p>This General Building Code Test Certificate (abP) consists of 7 pages and 5 annexes. <br />This translation is not checked by the testing laboratory. The legally binding text is the German <br />Version. This translation may not be used in the German building control procedure.</p> <p>Materialprüfanstalt für das <br />Bauwesen (MPA BS) <br />Beethovenstraße 52 <br />D-38106 Braunschweig</p> <p>Fon +49 (0)531-391-5400 <br />Fax +49 (0)531-391-5900 <br />info@mpa.tu-bs.de <br />www.mpa.tu-bs.de</p> <p>Norddeutsche LB Hannover <br />IBAN: DE58 2505 0000 0106 0200 50 <br />BIC: NOLADE2H <br />VAT ID No.: DE183500654 <br />Tax Reg. No.: 14/201/22859</p> <p>Notified body (0761-CPR) Approved as a civil engineering testing, <br />inspection and certifying body as well as <br />notified as a civil engineering testing and <br />certifying body.</p> <p>MPA BRAUNSCHWEIG <br />Page 2 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>A</p> <p>General provisions</p> <p>(1)</p> <p>This general building authority test certificate demonstrates the usability of the construction <br />product as defined by the German State Building Codes.</p> <p>(2)</p> <p>The general building authority test certificate does not replace the permits, approvals and <br />certificates required by law for the execution of construction projects.</p> <p>(3)</p> <p>The general building authority test certificate is granted without prejudice to the rights of third <br />parties, including, but not limited to, private intellectual property rights.</p> <p>(4)</p> <p>Manufacturers and distributors of the construction product must provide the user of the <br />construction product with copies of the general building inspectorate test certificate and point <br />out that the general building inspectorate test certificate must be available at the point of use, <br />without prejudice to further regulations in the “Special provisions”. Upon request, the <br />manufacturer/distributor must provide copies of the general building inspection test certificate <br />to the authorities involved or to the test engineers and experts or institutions involved in the <br />building inspection procedure.</p> <p>(5)</p> <p>The general building authority test certificate may only be reproduced in full. Publication of <br />excerpts requires the consent of the Braunschweig Civil Engineering Materials Testing Institute <br />(MPA Braunschweig). Texts and drawings of advertising material must not contradict the <br />general building authority test certificate. Translations of the general building authority test <br />certificate must bear the following notice: “This translation of the German original document <br />has not been checked by the MPA Braunschweig”.</p> <p>(6)</p> <p>The general building authority test certificate is issued on a revocable basis. The provisions of <br />the general building inspectorate test certificate may be supplemented and amended at a later <br />date, in particular if technical findings make this necessary.</p> <p>(7)</p> <p>The general building authority test certificate refers to the information and documents provided <br />by the applicant. Changes to these basic principles are not covered by the general building <br />authority test certificate.</p> <p>MPA BRAUNSCHWEIG <br />Page 3 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>B</p> <p>Special provisions</p> <p>1</p> <p>Test item and field of application</p> <p>1.1</p> <p>Test item <br />This General Building Code Test Certificate (abP) applies to the fabrication and use of the <br />"AQUAFIN-CJ6" swellable joint sealing tape in connection with the installation adhesive <br />“AQUAFIN-CA“ of SCHOMBURG GmbH & Co.KG for internal sealing of construction joints in <br />structural elements made from concrete with a high water penetration resistance in accordance <br />with the Administrative Provisions – Technical Building Rules sequential no. C 3.30. <br />The "AQUAFIN-CJ6" swellable tape is produced in rectangles of 20 mm x 5 mm (width <br />x height).</p> <p>1.2</p> <p>Field of application <br />The swelling tape may be used for the internal sealing of construction joints in structural <br />elements made from concrete with a high water penetration resistance, with a maximum <br />opening width of 0.25 mm, against: <br />-</p> <p>Ground moisture and non-pressing water <br />Pressing water up a maximum water pressure of 0.8 bar (8 m WC)</p> <p>The swelling tape is suited for use in zones of frequently changing water levels. The sealing <br />complies with utilisation-class A requirements for application classes 1 and 2 as set forth in the <br />regulations for watertight structures (WU-Richtlinie)1. <br />The swelling tape must be applied as specified in section 4 (Execution). The sealing effect of <br />the tape is based on its ability to swell.</p> <p>2</p> <p>Provisions concerning the construction product</p> <p>2.1</p> <p>Composition, properties and characteristics <br />The AQUAFIN-CJ6 swellable tape is based on a thermoplastic elastomer. It is coated and <br />comes in rolled lengths of 25 metres. For application of the swellable tape to the hardened <br />concrete, either the installation adhesive “AQUAFIN-CA“ (supplied in 300-ml cartridges). <br />The construction products have the characteristic values that are shown in table 1 and annexes <br />1 to 3, which they must comply with. <br />The fitness for use of the swelling tape as a sealing means for construction joints in structural <br />elements made from concrete with a high water penetration resistance has been demonstrated <br />in accordance with the test principles for certification with General Building Code Test <br />Certificates (abP) for "joint waterproofing elements in structural elements made from concrete <br />with a high water penetration resistance when in contact with the ground" (PG-FBB, Part 1, <br />May 2020). Results are documented in Test Repors No. 5196/307/10 issued by MPA <br />Braunschweig.</p> <p>1</p> <p>German committee for RC directive “Wasserundurchlässige Bauwerke aus Beton” (watertight structures made from <br />concrete), December 2017</p> <p>MPA BRAUNSCHWEIG <br />Page 4 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>Construction joints that are sealed with the swelling tape <br />•</p> <p>provide adequate stability</p> <p>•</p> <p>are adequately impervious to water</p> <p>•</p> <p>provide adequate age resistance</p> <p>for the fields of application mentioned in section 1.2 above. <br />The reaction to fire of the swellable tape conforms with the class-E requirements in <br />DIN EN 13501-1.</p> <p>2.2</p> <p>Production, packaging, transport, storage, marking</p> <p>2.2.1</p> <p>Production <br />The construction products are produced industrially.</p> <p>2.2.2</p> <p>Packaging, transport, storage <br />The swelling tape is packed in boxes containing rolls of 25 metres each. The product has to be <br />handled and stored, so the swelling tape, the adhesive and the mounting rail will not be <br />adversely affected in their designed properties. The materials have to be protected against the <br />action of frost and atmospheric influence. <br />The information provided on the packaging regarding other official requirements must be <br />complied with. <br />The manufacturer's specifications regarding storage periods shall be complied with. System <br />components that have to be used together must be clearly marked and marketed together.</p> <p>2.2.3</p> <p>Marking</p> <p>2.2.3.1 Conformity mark (Ü mark) <br />The manufacturer shall mark the construction products with the conformity mark (Ü mark) in <br />compliance with the conformity marking regulations of the federal states. The conformity mark <br />with the required details: <br />• <br />•</p> <p>Name of manufacturer <br />Number of the General Building Code Test Certificate (abP)</p> <p>shall be shown on the packaging or, if this should not be possible, in the package leaflet. This <br />marking may be provided only if the conditions set forth in section 3 below are complied with. <br />2.2.3.2 Additional details <br />The following details must be shown on the packaging of the construction product or in package leaflet: <br />• Product name <br />• Lot number <br />• Intended use <br />• Reference to application requirements</p> <p>MPA BRAUNSCHWEIG <br />Page 5 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>3</p> <p>Declaration of conformity</p> <p>3.1</p> <p>General information <br />Confirmation that the construction product conforms with the requirements set forth in the <br />present General Building Code Test Certificate (abP) shall be provided for each production <br />plant in the form of a manufacturer’s declaration of conformity. This declaration shall be issued <br />on the basis of an initial type test and factory production control (FPC) in accordance with <br />sections 3.2 and 3.3 below. The manufacturer shall declare conformity by marking the <br />construction product with the conformity mark (Ü mark) in accordance with 2.2.3.1.</p> <p>3.2</p> <p>Initial type test of the construction product performed by an approved <br />inspection body <br />An initial type test is not required for the product, if the samples used for testing for purposes <br />of a general type approval were taken from the normal production run in the production plant. <br />If the conditions under which the product is manufactured should change, the initial type test <br />must be repeated.</p> <p>3.3</p> <p>Factory production control (FPC) <br />DIN 18200 requires that factory production control (FPC) be established for, and be performed <br />in the production plant. <br />Factory production control must be performed in compliance with the specifications shown in <br />table 1, which reflect the special features of the product and the conditions for producing this <br />product. The requirements made are based on the results of the initial type test. <br />The results of factory production control must be recorded and evaluated by the manufacturer. <br />The records must at least include the following details: <br />• <br />• <br />• <br />• <br />•</p> <p>Name of the product <br />Type of test or inspection <br />Date when produced and date of test <br />Test results and comparison with requirements <br />Signature of person in charge of factory production control</p> <p>The records must be kept for a minimum of five years and must be presented upon request. <br />Should testing supply inadequate results, the manufacturer must take immediate action to <br />remedy any deficiencies noted. Non-conforming construction products must be handled so that <br />confusion with conforming and faultless construction products is positively prevented. Once <br />the deficiency has been corrected, the required test must be repeated to the extent that is <br />necessary to prove adequate correction.</p> <p>MPA BRAUNSCHWEIG <br />Page 6 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>Table 1: Type and frequency of tests to be performed as part of factory production control <br />Properties</p> <p>Test conditions</p> <p>Requirements</p> <p>Frequency</p> <p>AQUAFIN-CJ6 swellable tape <br />Inspection of <br />source materials</p> <p>Manufacturer's <br />declaration or <br />suitable tests</p> <p>No signs of change</p> <p>Per shipment lot <br />Per lot</p> <p>Height</p> <p>-</p> <p>5.2mm ± 5%</p> <p>Width</p> <p>-</p> <p>21.4mm ± 5 %</p> <p>Weight</p> <p>-</p> <p>122 g/m ± 3%</p> <p>Per lot</p> <p>Stored for 8 days in <br />(demin.) water</p> <p>1040 wt % ± 10%</p> <p>Per lot</p> <p>Swelling capacity <br />(gain in weight)</p> <p>Installation adhesive AQUAFIN-CA <br />Inspection of <br />source materials</p> <p>4</p> <p>Manufacturer's <br />declaration or <br />suitable tests</p> <p>No signs of change</p> <p>Per shipment lot</p> <p>Density</p> <p>cf. Annex 1</p> <p>0.97 g/cm³ ± 3%</p> <p>Per lot</p> <p>Infrared <br />spectrum</p> <p>cf. Annex 3</p> <p>No signs of change</p> <p>Per lot</p> <p>Execution <br />The DBV data sheet “Injection hose systems and swellable inserts for construction joints”, <br />version December 2020 and the manufacturer's technical data sheets (Annexes 4 and 5) apply <br />to the execution and installation work. <br />In the joint region, the concrete surface must be dry to moist (without a glossy water film), plane <br />and clean, and it must be free from loose material, cement slurry and release agents. <br />The swellable tape must always be glued to the concrete surface with the installation adhesive <br />“AQUAFIN-CA“. The swelling tape has to be checked for perfect fit and premature swelling <br />immediately before placing the concrete. <br />This General Building Code Test Certificate and the manufacturer's processing instructions <br />must be available at the installation location.</p> <p>5</p> <p>Legal basis <br />This General Building Code Test Certificate (abP) is issued on the basis of article 19 of the <br />building code of Lower Saxony (NbauO) in conjunction with the Administrative Provisions – <br />Technical Building Rules sequential no. C 3.30.</p> <p>MPA BRAUNSCHWEIG <br />Page 7 | General Building Code Test Certificate No.P-5196/307/09 MPA-BS of 09/03/2025</p> <p>6</p> <p>Legal remedy <br />This General Building Code Test Certificate (abP) is subject to objection. Objections must be <br />lodged in writing or stated orally on the record of the management of Materialprüfanstalt für <br />das Bauwesen, Beethovenstraße 52, 38106 Braunschweig within a period of one month after <br />it has been issued. The date on which the Testing Laboratory receives the notice of objection <br />shall decide on whether the objection was made timely.</p> <p>Dipl.-Min. F. Ehrenberg <br />Head of Testing Laboratory</p> <p>i. A. <br />M. Pankalla <br />Engineer/Official in Charge</p> <p>MPA BRAUNSCHWEIG <br />Annex 1 | General Building Code Test Certificate No. P-5196/307/09 MPA-BS of 09/03/2020</p> <p>Properties of the AQUAFIN-CJ6 swellable joint tape <br />•</p> <p>Appearance:</p> <p>red, rubber-elastic, homogeneous</p> <p>•</p> <p>Density:</p> <p>1.25 g/cm³</p> <p>•</p> <p>Weight loss: <br />(TGA, 25° C to 1000° C)</p> <p>73.4 wt %</p> <p>•</p> <p>TGA:</p> <p>see annex 2</p> <p>•</p> <p>Swelling capacity after <br />(gain in weight) <br />- Ca(OH)2 storage (pH 12):</p> <p>2 h = 21 wt % <br />1 d = 139 wt % <br />8 d = 428 wt %</p> <p>- H2SO4 storage (pH 4.5):</p> <p>2h= <br />9 wt % <br />1 d = 99 wt % <br />8 d = 301 wt %</p> <p>- Storage in water (demin.):</p> <p>2 h = 54 wt % <br />1 d = 464 wt % <br />8 d = 1043 wt %</p> <p>•</p> <p>Swelling pressure:</p> <p>1.06 N/mm²</p> <p>•</p> <p>Flammability:</p> <p>class E acc. to DIN EN 13501-1</p> <p>Properties of the installation adhesive AQUAFIN-CA <br />•</p> <p>Appearance:</p> <p>transparent, clear, paste-like, homogeneous</p> <p>•</p> <p>Density:</p> <p>0.97 g/cm³</p> <p>•</p> <p>Infrared spectrum:</p> <p>see annex 3</p> <p>MPA BRAUNSCHWEIG <br />Annex 2 | General Building Code Test Certificate No. P-5196/307/09 MPA-BS of 09/03/2020</p> <p>Thermogravimetric analysis</p> <p>AQUAFIN-CJ6 swelling tape</p> <p>Thermogravimetric analyses were made on thebasis of DIN EN ISO 11358 specifications. The heating rate <br />was 10 K/minute. Measurements were made with a thermoanalysing station in a nitrogen atmosphere and <br />with synthetic air. The weight loss was determined at temperatures between 25°C and 1000°C.</p> <p>TG /%</p> <p>DTG /(%/min) <br />[1]</p> <p>100</p> <p>0</p> <p>90 <br />-1 <br />80 <br />-2 <br />70 <br />Peak: 709.9 °C</p> <p>-3</p> <p>Peak: 330.9 °C</p> <p>60</p> <p>-4</p> <p>50</p> <p>40</p> <p>-5 <br />Peak: 722.0 °C</p> <p>Masseverlust 25°C bis 1000°C = 73,4% <br />30</p> <p>Hauptansicht</p> <p>[1]</p> <p>Peak: 450.0 °C <br />100</p> <p>200</p> <p>2009-11-04 12:40</p> <p>Nut zer: Obermann</p> <p>300</p> <p>400</p> <p>500 <br />Temperatur /°C</p> <p>600</p> <p>700</p> <p>800</p> <p>-6</p> <p>900 <br />2009t196.ngb</p> <p>MPA BRAUNSCHWEIG <br />Annex 3 | General Building Code Test Certificate No. P-5196/307/09 MPA-BS of 09/03/2020</p> <p>Infrared spectrum</p> <p>Installation adhesive AQUAFIN-CA</p> <p>The IR analyses were made with a Perkin-Elmer FTIR unit of type Spectrum 2000 Explorer, wave number range 4000 <br />cm-1 to 600 cm-1. The quantities of the samples were selected so that the DIN 51451 requirements respecting extinction <br />conditions were complied with. <br />The installation adhesive was removed from the cartridge, applied to a ZnSe sample holder (without having been <br />preconditioned) and then analysed under the spectroscope. <br />Materialprüfanstalt für das Bauwesen, Braunschweig <br />100,00</p> <p>90,0</p> <p>80,0</p> <p>907,1 <br />2728,1</p> <p>70,0</p> <p>1601,5 <br />813,5</p> <p>3084,0</p> <p>60,0</p> <p>%T</p> <p>3060,4</p> <p>50,0 <br />3026,3 <br />759,2</p> <p>1493,9</p> <p>40,0 <br />1377,5</p> <p>30,0 <br />1746,5</p> <p>20,0 <br />1229,1 <br />699,2 <br />1455,8</p> <p>10,0 <br />2924,3 <br />1116,3 <br />2853,6</p> <p>0,00 <br />4000,0</p> <p>3600</p> <p>3200</p> <p>2800</p> <p>2400</p> <p>2000</p> <p>1800 <br />cm-1</p> <p>1600</p> <p>1400</p> <p>1200</p> <p>1000</p> <p>800</p> <p>600,0</p> <p>A hardened sample of the material (7-day hardening time) was analysed with the Golden Gate Single Reflection ATR <br />System. <br />Materialprüfanstalt für das Bauwesen, Braunschweig <br />100,00</p> <p>90,0</p> <p>80,0</p> <p>70,0 <br />1600,5</p> <p>759,0</p> <p>60,0 <br />1376,2</p> <p>%T</p> <p>50,0</p> <p>699,7 <br />630,3</p> <p>40,0 <br />1454,8</p> <p>30,0</p> <p>20,0 <br />1105,6 <br />2851,6</p> <p>10,0</p> <p>2919,6</p> <p>0,00 <br />4000,0</p> <p>3600</p> <p>3200</p> <p>2800</p> <p>2400</p> <p>2000</p> <p>1800 <br />cm-1</p> <p>1600</p> <p>1400</p> <p>1200</p> <p>1000</p> <p>800</p> <p>600,0</p> <p>MPA BRAUNSCHWEIG <br />Annex 4 | General Building Code Test Certificate No. P-5196/307/09 MPA-BS of 09/03/2020</p> <p>Manufacturer's Technical Data Sheet</p> <p>MPA BRAUNSCHWEIG <br />Annex 5 | General Building Code Test Certificate No. P-5196/307/09 MPA-BS of 09/03/2020</p> <p>Manufacturer's Technical Data Sheet</p>
