SOLOPLAN-FA_Product_information_GB_2716.pdf
2 Pages
279 KB
Download
<h1>SOLOPLAN-FA_Product_information_GB_2716.pdf</h1> <p>Product information <br />Smoothing and levelling compounds</p> <p>SOLOPLAN®-FA <br />Self levelling, fibre reinforced <br />floor levelling compound <br />C30-F7</p> <p>Technical Data: <br />Basis: </p> <p>Special cement, aggregates, additives</p> <p>Classification: </p> <p>EN 13813 CT-C30-F7</p> <p>Application temperature: +15°C to +25°C <br />Pot life*: </p> <p>approx. 20–30 mins</p> <p>Water addition: 6.0–6.3 l water : 25 kg <br />SOLOPLAN-FA <br />Consumption: </p> <p>approx. 1.6 kg/m²/mm thickness</p> <p>Foot traffic*: </p> <p>after approx. 3 hrs</p> <p>Ready for finishes*: </p> <p>after approx. 24 hrs</p> <p>Full service conditions*: </p> <p>after approx. 7 days</p> <p>Reaction to fire: </p> <p>Class E</p> <p>Packaging: </p> <p>25 kg plastic bag</p> <p>TS/CoS/JD</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>27/16</p> <p>Areas of application: <br />• SOLOPLAN®-FA is a powder based, highly modified factory <br />blended mortar with reinforcing fibres, which minimises cracks <br />on wooden floors. For producing self-levelling flat, high strength <br />substrates to receive ceramic tiles and slabs. On wooden floors <br />at thicknesses from 3 to 20 mm. <br />• SOLOPLAN®-FA can be installed over wooden floorboards and <br />V100 grade chipboard, without additional reinforcing mesh as <br />well as on all mineral-based substrates. <br />• SOLOPLAN®-FA is also suitable for rooms with light duty water <br />exposure (wet duty exposure class A0 in accordance with the <br />ZDB information sheet “Bonded waterproof membranes”) when <br />treated with a suitable SCHOMBURG waterproof membrane. <br />• SOLOPLAN®-FA is suitable for use in interior rooms in <br />accordance with the French VOC by-law and is very low <br />emissions in accordance with GEV EMICODE.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>*) Values are valid at +23° C and 65% relative humidity.</p> <p>2 00011</p> <p>Product application: <br />Place 6.0–6.3 l water, dependent on desired consistency, in a clean <br />suitable mixing container and mix together with 25 kg SOLOPLAN®-FA to a <br />lump-free, flowing mass. After standing for an adequate time to mature, <br />pour the mixed levelling compound onto the prepared substrate. To ensure <br />even distribution of the material, use a suitable rake or trowel. This should <br />be followed by de-aerating the fresh material by rolling through with a <br />spiked roller. For installing SOLOPLAN®-FA in large areas, we recommend <br />suitable mixing equipment such as e.g. PFT G4/ G5.</p> <p>SOLOPLAN®-FA <br />Self levelling, fibre reinforced <br />floor levelling compound</p> <p>Properties: <br />• For thicknesses from 3 to 20 mm <br />in one application <br />• Fibre reinforced <br />• Self levelling <br />• Rapid hardening <br />• Very low emissions <br />• Very low consumption <br />• For interiors <br />• Suitable for heated screeds <br />• Pumpable</p> <p>1 Load-bearing substrate</p> <p>2 Cleaning the substrate</p> <p>Priming:</p> <p>3 Priming the substrate, e.g. with <br />ASO®-Unigrund</p> <p>4 Placing the edge isolating strip RD-SK50</p> <p>5 Adding the levelling compound to the preweighed water</p> <p>6 Mixing the levelling compound</p> <p>7 Tipping out the levelling compound</p> <p>8 Evening and de-aerating the fresh levelling <br />compound</p> <p>Calcium sufate screed: ASO®-Unigrund-S <br />(Mixing ratio 1:1 with water) <br />Cement-based screed: ASO®-Unigrund-S <br />(Mixing ratio 1:1 with water) <br />Wooden substrates <br />(screwed) <br />such as e.g. <br />OSB boards, wooden floor <br />boards, V100 chipboard: ASO®-Unigrund-S <br />Well bonded ceramic tiles, <br />terrazzo: ASODUR®-SG2 *</p> <p>io n</p> <p>ve</p> <p>ry</p> <p>Application: <br />The substrate must be dry, load-bearing, sound with a good key, free from <br />materials acting as separating substances. Remove separating layers, <br />laitance or similar by suitable means e.g. by mechanical blasting <br />techniques or scabbling. With unbonded or floating screeds, the readiness <br />to receive SOLOPLAN®-FA is to be tested by the carbide (CM) method <br />(• CT ≤ 2.0 %, • CA/ CFA unheated ≤ 0.5 %, heated ≤ 0.3 %). <br />The residual moisture of the wooden substrate may not exceed an <br />equilibrium moisture content of 6 to 12% by weight. Screw fix all loose, <br />springy or squeaking boards or sheets. Abrade wooden substrates and <br />thoroughly vacuum.</p> <p>l o w e m iss</p> <p>*Blinded to excess with 0.5 – 1.0 mm quartz sand. Only sweep off and <br />vacuum excess sand once reacted (approx. 16 hrs *1).</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold <br />14 <br />2 00012 <br />EN 13813 <br />SOLOPLAN®-FA <br />Cement screeding mortar for <br />use in buildings <br />CT-C30-F7 <br />Reaction to fire: <br />Release of corrosive <br />substances: <br />Compressive strength: <br />Flexural strength: </p> <p>Class E <br />CT <br />C30 <br />F7</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>9 Finished levelled floor ready for finishes</p>
