Product information Smoothing and levelling compounds
SOLOCRET®-50 Anti-sag smoothing compound – rapid hardening
Technical Data: Basis:
Special cement, aggregate, high quality additives
Flexural and compressive strength*:
4.0 N/mm²/25 N/mm² after 28 days
Application temperature:
+5 °C to +25 °C
Pot life*:
min. 30 mins
Water addition: 4.0–4.5 l water : 25 kg SOLOCRET®-50 (dependent on thickness installed) Consumption:
approx. 1.5 kg/m²/mm thickness
Overcoat*:
after approx. 3–4 hrs
Foot traffic*:
after approx. 7 day
Packaging:
25 kg plastic bag
TS/CoS/JD
SCHOMBURG GmbH & Co. KG Aquafinstrasse 2–8 D-32760 Detmold (Germany) phone +49-5231-953-00 fax +49-5231-953-108 email export@schomburg.de www.schomburg.com
26/16
Areas of application: • SOLOCRET®-50 is a rapid hardening, highly slump resistant smoothing compound for use at thicknesses from 2-50 mm in one application for preparing substrates before the subsequent installation of ceramic tiles and slabs, natural and artificial stone as well as other finishes, including over underfloor heating. • SOLOCRET®-50 can be used on suitable substrates such as e.g. mineral-based substrates; concrete to DIN 1045, heated and unheated cement-based screeds to DIN 18560, cement-based renders, old well adhered tiled finishes and rapid setting cement-based screeds. • SOLOCRET®-50 is suitable for exterior and wet duty areas when an appropriate SCHOMBURG bonded waterproof membrane is installed.
Subject to changes. Consult current technical data sheet for most recent information.
*) Values are valid at +23° C and 50% relative humidity.
2 05440
1 Load-bearing substrate
2 Cleaning the wall substrate
3 Priming the substrate, e.g. with ASO-®Unigrund
4 Adding the smoothing compound to the pre-weighed water
5 Mixing the smoothing compound
6 Levelling uneven areas in walls
7 Cleaning the floor substrate
8 Priming the substrate, e.g. with ASO®-Unigrund
9 Levelling and/or creating falls in the floor
10 Even walls and floor ready to receive finishes
Properties: • For thicknesses from 2 - 50 mm in one application • Rapid hardening • Low shrinkage • Smooth and easy application • For interior and exterior use • Suitable for heated screeds • For walls, ceilings and floors
Product application: Prime the substrate with ASO-Unigrund. Cement-based substrates can also be pre-wetted until matt damp. Mix SOLOCRET®-50 at a ratio of approx. 4.0 to 4.5 l water : 25 kg SOLOCRET®-50 with clean water in a clean mixing bucket with a suitable drill mixer for approx. 3-5 minutes until homogenous. After standing for approx. 5 mins, stir through once again. Do not mix more material than can be used within 30 minutes. Produce a scratch coat and then trowel out SOLOCRET®-50 and spread evenly with a suitable tool (plasterer’s darby) within the working life of the product. SOLOCRET®-50 can be applied to surfaces at a thickness of 50 mm in one application and for localised defects also to a thickness of 100 mm. After approx. 60–80 minutes (dependent on the substrate, ambient conditions and thickness), SOLOCRET®-50 can be smoothed off or roughened with a grid float to remove uneven areas and produce a rough surface texture, which provides a good key for subsequent applications of bonded materials.
Application: The substrate must be dry, load-bearing, adequately flat, free from penetrating cracks and free from separating substances such as e.g. oil, paints, laitance layers and loose components. It must have a largely closed texture and possess surface characteristics and strength typical for its type. Prime absorbent substrates with ASO®-Unigrund. Heat substrates with underfloor heating before applying finishes. The readiness of a substrate to receive finishes is to be determined using the carbide (CM) method and may not fall below the following values: •CT ≤ 2.0 % •CA/ CFA unheated ≤ 0.5 %, heated ≤ 0.3 %