ESCOSIL-2000-UW_Product_Information_GB_4915.pdf
2 Pages
262 KB
Download
<h1>ESCOSIL-2000-UW_Product_Information_GB_4915.pdf</h1> <p>Product information <br />Elastic joint sealer</p> <p>ESCOSIL®-2000-UW <br />Silicone for underwater use</p> <p>Technical Data: <br />Basis: pure, unmodified, neutral curing silicone sealant, silicone oils <br />Colours: </p> <p>medium grey, cement grey</p> <p>Consistency: paste <br />Application temperature: +5 °C to +35 °C <br />Curing after 1 day: </p> <p>approx. 2–3 mm, at +23 °C and 50 % relative humidity</p> <p>Skin formation: </p> <p>approx. 6 minutes, at +23 °C and 50 % relative humidity</p> <p>Temperature resistance: </p> <p>-40 °C to +180 °C</p> <p>Permissible movement <br />accommodation: </p> <p>25 % *</p> <p>Shore-A-hardness: </p> <p>approx. 24, acc. to DIN 53505</p> <p>Consumption: </p> <p>dependent on joint cross-section and depth</p> <p>Packaging: 310 ml, polyethylene cartridges, <br />(12 × 310 ml tubes per box)</p> <p>* Colour differences may exist due to print limitations.</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>TS/CoS/JD</p> <p>Areas of application: <br />• ESCOSIL®-2000-UW is used for the elastic jointing of <br />expansion and construction joints in swimming pools, water <br />features etc. or where an especially high fungicidal <br />performance is desired.</p> <p>cement grey</p> <p>49/15</p> <p>medium grey</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>Colour illustration*:</p> <p>2 05591</p> <p>Product application: <br />Once any applied primer has dried (see technical data sheet), filling can be <br />undertaken with ESCOSIL®-2000-UW. Using a caulking gun, extrude <br />ESCOSIL®-2000-UW into the prepared joint. Then smooth the applied <br />sealant before it forms a skin, with a suitable tool and water containing a <br />surfactant. This process ensures the material is pressed into the joint and at <br />the same time pressed against the contact surfaces. Do not expose to water <br />contact until after 4 days at the earliest. Follow the general rules for <br />producing elastic joints.</p> <p>ESCOSIL®-2000-UW <br />Silicone for underwater use</p> <p>Properties: <br />• 1 component <br />• Acetic cross-linking <br />• Elastic <br />• High level of fungicide <br />• Resistant to chemicals and <br />chlorine <br />• Weather-, UV- and <br />ageing-resistant <br />• Watertight <br />• For walls and floors</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p> <p>Please take supplementary advice from the current valid technical data <br />sheet.</p> <p>1 ESCOSIL®-2000-UW and suitable tool</p> <p>2 Installation of a suitable backing strip</p> <p>3 Application of ESCOSIL®-2000-UW</p> <p>4 Application of a suitable smoothing agent</p> <p>5 Striking off excess silicone sealant</p> <p>6 Subsequent smoothing</p> <p>Application: <br />The surfaces with which the sealant will be in contact must be dry (concrete <br />< 4% moisture), clean, dust free as well as free from all substances, which <br />act as separating agents (e.g. oil, paint residues, sealants, cement slurries, <br />grout residues etc.). Whilst ESCOSIL®-2000-UW hardens, no moisture may <br />be allowed to penetrate from the edges or the base of the joint. <br />Only expose to water contact after 4 days at the earliest!</p>
