CRISTALLFUGE-Plus_Produktinformation_0122.pdf
2 Pages
482 KB
Download
<h1>CRISTALLFUGE-Plus_Produktinformation_0122.pdf</h1> <p>Properties <br />• Rapid crystalline binding of the mixing water <br />• Protected against bacterial and fungicidal attack <br />• Protects against discolouration caused by the <br />stone's own components with sensitive laying <br />materials <br />• Rapid setting <br />• Good binding and wash-off properties <br />• Smooth consistency <br />• Vapour permeable <br />• Pigmented <br />• Polymer modified <br />• Cures without cracks <br />• For floor and wall heating systems <br />• Colours matched to the ESCOSIL-2000 and <br />ESCOSIL-2000-ST silicone system <br />Areas of use <br />• CRISTALLFUGE-PLUS is suited especially <br />to grouting joints in natural stones free of <br />discolouration, e.g. limestones, Jura marble, <br />Solnhofer boards, sensitive bright crystalline <br />marble, granite, and ceramic made of porcelain <br />stoneware, earthenware, vitrified tiles, glass <br />mosaics, and more. <br />• CRISTALLFUGE-PLUS can be used for joint widths <br />up to 10 mm in the interior and exterior area for <br />heated wall and floor structures, mainly in dry, <br />damp, and wet areas.</p> <p>Application <br />• After the bedding mortar sets, scratch out the joints sufficiently deep. <br />• Next, clean the tiled finish sufficiently damp. <br />• The bedding mortar must be fully set, since otherwise discolourations in <br />the grout finish could result. <br />• Pre-moisten strongly absorbing coverings with water equally. <br />• Joint edges must be clean and free of separating substances. <br />• The time of grouting of the tiles set in the thin-bed depends on the thinbed mortar and amounts to approx. 3 to 72 hours. <br />• In case of thick-bed laying, the mortar bed must be sufficiently firm and <br />equally dry. <br />• Do not grout on surfaces with different surfaces temperatures (e.g. due to <br />sun exposure). <br />• The consistency of joint mortar must be specified depending on the <br />absorbency of the covering and substrate to be grouted.</p> <p>2 CRISTALLFUGE-PLUS, suitable tools</p> <p>3 Fill the joint mortar into a clean mixing bucket</p> <p>4 Mix the joint mortar</p> <p>5 Apply the joint mortar</p> <p>6 Sliding diagonally across excess joint mortar</p> <p>7 Moisten and press out the clean sponge <br />board</p> <p>8 Emulsify the joint mortar after setting</p> <p>9 Rinsing off surfaces diagonally to the joint <br />direction</p> <p>10 Finished and jointed wall surface</p> <p>Consumption table <br />Tiles/boards <br />format (in cm)</p> <p>Joint width <br />(in mm)</p> <p>Joint depth <br />(in mm)</p> <p>Approx. <br />consumption in m2 <br />(in kg)</p> <p>2×2</p> <p>1.5</p> <p>2.0</p> <p>0.6</p> <p>2×2</p> <p>1.5</p> <p>10.0</p> <p>2.9</p> <p>10 × 10</p> <p>3.0</p> <p>6.0</p> <p>0.7</p> <p>20 × 30</p> <p>3.0</p> <p>8.0</p> <p>0.4</p> <p>30 × 30</p> <p>3.0</p> <p>10.0</p> <p>0.4</p> <p>30 × 40</p> <p>3.0</p> <p>10.0</p> <p>0.5</p> <p>30 × 60</p> <p>3.0</p> <p>10.0</p> <p>0.3</p> <p>30 × 60</p> <p>3.0</p> <p>20.0</p> <p>0.6</p> <p>30 x 90</p> <p>3.0</p> <p>20.0</p> <p>0.6</p> <p>v er</p> <p>y lo</p> <p>w e m is</p> <p>s</p> <p>an</p> <p>ti b</p> <p>* Informationen über das Emissionsniveau von flüchtigen Stoffen in <br />der Raumluft, die bei Inhalation Gesundheitsrisiken, auf einer Skala <br />von Klasse A + (sehr emissionsarm) bis C (hohe Emissionen), darstellen.</p> <p>l</p> <p>Multifunctional, rapid, flexible, fine-joint <br />mortar 1–10 mm, CG 2 WA</p> <p>1 Available wall surface, bonding bed is set</p> <p>Please refer to the currently valid technical data sheet for <br />additional instructions.</p> <p>el</p> <p>joint mortar <br />CRISTALLFUGE-PLUS</p> <p>Application <br />1. Mix CRISTALLFUGE-PLUS with clean water in a clean mixing bucket. <br />Add 1.25 l water depending on the desired consistency and the type of <br />ceramic to be joined, add 5 kg CRISTALLFUGE-PLUS, and then stir into <br />a homogeneous, smooth mass. We recommend mixing with a suitable <br />stirrer. After an activation time of 2 min., the joint mortar is stirred again. <br />In order to avoid colour differences, the mix ratio must always be kept <br />the same. <br />2. CRISTALLFUGE-PLUS is added to the wall or floor areas with a suitable <br />jointing board and pulled diagonally to the joint cleanly, so that the joint <br />cross-section is filled completely. Do not scatter dry joint mortar powder. <br />3. After applying the joint mortar (control via finger test), wash the surface <br />first with a moist sponge board. After approx. 15–45 minutes, <br />depending on the absorbency of the covering, wash after cleanly with <br />the sponge board.</p> <p>io n</p> <p>joint mortar</p> <p>a kter</p> <p>i</p> <p>Note: T he adjacent wall jointing process <br />is also valid for floor areas</p> <p>joint mortar <br />CRISTALLFUGE-PLUS <br />Multifunctional, rapid, flexible, fine-joint mortar 1–10 mm, <br />CG 2 WA</p> <p>Special cement, mineral aggregate materials, and <br />high-quality additives</p> <p>Colours</p> <p>white, silver-grey, grey, jasmine, parchment, beige, caramel, Jura beige, brown, nut brown, medium grey, <br />titanium grey, graphite, Bahamas beige, sand grey</p> <p>Classification</p> <p>EN 13888 CG 2 WA</p> <p>Application temperature</p> <p>+5 °C to +25 °C</p> <p>Pot life*</p> <p>approx. 30–45 minutes</p> <p>Water addition</p> <p>approx. 1.3 l water: 5 kg CRISTALLFUGE-PLUS</p> <p>Consumption</p> <p>see consumption table</p> <p>Foot traffic* <br />Withstands loads*</p> <p> fter approx. 2 hours <br />a <br />after 1 day at the earliest</p> <p>Packaging</p> <p>5 kg foil bag, <br />10 kg foil bag</p> <p>*at +20 °C, 65 % rel. humidity</p> <p>Colours*</p> <p>silver grey</p> <p>white</p> <p>jasmine</p> <p>pergamon</p> <p>beige</p> <p>caramel</p> <p>Jura beige</p> <p>brown</p> <p>nut brown</p> <p>grey</p> <p>medium grey</p> <p>Titanium grey</p> <p>graphite</p> <p>Bahama beige</p> <p>sand grey</p> <p>* Colour deviations are due to printing technology.</p> <p>SCHOMBURG GmbH <br />Aquafinstraße 2–8 <br />D-32760 Detmold (Germany) <br />Telephone +49-5231-953-00 <br />Fax <br />+49-5231-953-333 <br />www.schomburg.com</p> <p>01/22 TS/Tet/LiW</p> <p>Basis</p> <p>Subject to change without prior notification. The valid issue of the corresponding technical bulletin legally applies.</p> <p>Technical data</p>
