Method Statement_BETOCRETE-CP360-WP_0720.pdf
3 Pages
601 KB
Download
<h1>Method Statement_BETOCRETE-CP360-WP_0720.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone + 49-5231- 953-00 <br />fax + 49-5231- 953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>Method Statement</p> <p>BETOCRETE-CP360-WP <br />Crystalline waterproofing concrete admixture</p> <p>Scope <br />This method statement covers powder crystalline <br />waterproofing admixture for concrete.</p> <p>Part 1 – General <br />This section covers materials, labour, tools and equipment <br />for installation and application of powder crystalline <br />waterproofing admixture that are used to produce <br />permanently active waterproof concrete. <br />1.1 Standards <br /> DIN EN 934-2 – Admixtures for concrete, mortar, <br />and grout – table 9: water resisting admixtures <br />1.2 Submittal <br />A. Submit two copies of Technical Data Sheet <br />containing all the instructions for use and <br />installation (TDS) and Material Safety Data Sheet <br />(MSDS). <br />B. Submit a list of SCHOMBURG GmbH & Co. KG <br />or your local SCHOMBURG/AQUAFIN <br />approved applicators (Please ask for an <br />applicator list). <br />1.3 Quality Assurance <br />A. Manufacturer Qualifications <br />The manufacturer shall certify that the specified <br />product is valid and suitable for use and <br />application as mentioned in the TDS. <br />B. Applicator Qualifications <br />Applicator shall be qualified in the field of <br />concrete protection and repair with successful <br />records. Applicator shall maintain qualified and <br />certified personnel with good repute. <br />C. Application and use of this product shall be in <br />accordance with all instructions and precautions <br />stated in the Technical Data Sheet. The MSDS <br />and local regulations should be followed during <br />handling, storage, applications and waste <br />disposal.</p> <p>1.4 Delivery, Storage and Handling <br />A. All materials shall be delivered in unopened and <br />original containers and fully identified with brand, <br />type, grade, class, batch numbers and all other <br />qualifying information. <br />B. All the delivered materials shall be stored in its <br />original packaging and elevated from the ground <br />on pallets or shelves (avoid direct contact with the <br />floor) according to the valid TDS. <br />C. All the necessary precaution shall be taken to keep <br />the product clean, dry and free from damage. <br />D. Shelf life is 12 months when stored according to <br />the above conditions and cool conditions above <br />+5 °C. <br />1.5 Job Conditions <br />A. Environmental conditions: the material shall not <br />be applied during rain and protect from strong <br />drafts. The application temperature must remain <br />lower than +40 °C, for lower temperature curing <br />time extends & for higher temperature curing time <br />reduces. During application at higher temperatures <br />protect material from direct sunlight.</p> <p>Part 2 – Product <br />2.1 Manufacturer <br /> BETOCRETE-CP360-WP as manufactured by <br />SCHOMBURG GmbH & Co. KG conforms to all <br />requirements of this method statement. <br />2.2 Materials <br /> Powder crystalline waterproofing admixture that <br />used to produce permanently active waterproof <br />concrete <br />Component: In powder form. <br />It is supplied in: <br /> 3 kg water-soluble bags <br /> 17 kg bags <br /> 700 kg big bags</p> <p>1/3</p> <p>07/20</p> <p>2.3 Performance Criteria <br /> BETOCRETE-CP360-WP has the following <br />properties: <br /> Colour: <br />grey <br /> <br />Form: Powder <br /> <br />Density: 0.80 g/cm³ <br /> <br />Application temp.: ≥ +5 °C <br /> Compressive strength <br />according to <br />EN 12390-3 ≥ 85 % compared to untreated <br />concrete after 28 days <br /> <br />Air content <br /> according to <br />EN 12350-7 ≤ 2 % higher volume share than <br />untreated concrete <br /> Capillary water intake <br />according to <br />EN 480-5 ≤ 60 % mass portion of <br />untreated concrete after <br />28 days and 90 days curing <br />time <br />≤ 50 % mass portion of <br />untreated concrete after 7 days <br />and 7 days curing time</p> <p>mixture is homogeneous specially when stored for <br />longer periods. Assure that the water/cement ratio <br />(w/c) does not exceed 0.55 (powder crystalline <br />waterproofing admixture is included</p> <p> <br />Dosage range <br /> <br />w/c ratio 0.4–0.5: 0.80 % by weight of CEM <br /> <br />> 0.5–0.55: 0.90 % by weight of CEM <br /> <br />Do not exceed 1.25 % by weight of CEM. <br /> <br /> <br /> <br /> <br /> <br /> <br /> <br /> </p> <p>Dosage in ready-mix factory: <br />BETOCRETE-CP360-WP can be dosed together <br />with the aggregate for at least 30 seconds before <br />adding water and cement. Then mix at least for <br />45 seconds. <br />Dosage in truck mixer on the job site: <br />Dose BETOCRETE-CP360-WP directly into the <br />mixing drum. Mix thoroughly mixed for 1 min per <br />m³ of concrete, but at least 5 minutes. Use quickly.</p> <p>Part 3 – Execution <br />3.1 General: <br /> Assure that concrete mix design and proposed <br />materials are in compliance with manufacturer’s <br />recommendations. Assure that test batching and <br />material testing, if recommended by manufacturer, <br />has been carried out prior to starting concrete <br />work. Comply with manufacturer’s product data <br />and installation instructions. <br />3.2 Application: <br /> Stir powder crystalline waterproofing admixture in <br />a container provided prior to use, to assure that the</p> <p>Minimum Cement Content: <br />CEM I: <br />270 kg/m3 <br />CEM II: <br />290 kg/m3 <br />CEM III /A: 380 kg/m3 <br />Puzzolanic cements <br />with puzzolan content > 20 %: 300 kg/m3 <br />Granulated slag: <br />max.100 kg/m3 <br />Fly ash: <br />max. 80 kg/m3</p> <p>3.3 Important Advice: <br />• Please ensure that pre-tests were made with all <br />admixtures that will be used in the concrete mix <br />• The addition of a concrete retarder can be <br />necessary when using Portland Cement Type <br />II or III. Suitability tests have to be carried out <br />before usage. <br />• It is rarely possible that <br />BETOCRETE-CP360-WP influences the setting <br />of the concrete. Our product REMITARD-20 (BV)</p> <p>2/3</p> <p>07/20</p> <p>has proven as the most effective retarder. <br />• Concrete modified with <br />BETOCRETE-CP360-WP may tend to effloresce <br />depending on the composition. <br />• If the BETOCRETE-CP360-WP was stored at <br />temperatures below +5 °C crystals may form, <br />BETOCRETE-CP360-WP is suitable for usage <br />again after warming up to minimum +15 °C <br />followed by stirring or homogenizing. <br />• Suitability tests according to valid standards <br />and norms have to be carried out prior to <br />application.</p> <p>3.4 Cleaning: <br /> Regular water flushing of dispensing equipment <br />will prolong service life and reduce breakdowns. <br />Use REINIT-BM on internal metal surfaces subject <br />to contact with concrete in concrete mixers, <br />batch plants and truck mixers regularly to prevent <br />concrete crust formations. Use ASO-R005 to <br />remove hardened concrete crusts.</p> <p>The rights of the buyer with regard to the quality of our materials are based on our terms and conditions of sale and delivery. Our technical advice team will be happy to advise you in the case <br />of requirements that exceed the scope of the application described here. In order to be binding, a legally binding written confirmation is required. The product description does not release the <br />user from a duty of care. Lay a test area in the event of uncertainty. This version becomes invalid in the event of a new version being issued. <br />3/3</p> <p>SE/KK 07/20</p>
