ASO-Unigrund-S_Product_Information_GB_4915.pdf
2 Pages
260 KB
Download
<h1>ASO-Unigrund-S_Product_Information_GB_4915.pdf</h1> <p>Product information <br />Primers</p> <p>ASO®-Unigrund-S <br />Rapid special adhesion promoting primer</p> <p>Technical Data: <br />Basis: </p> <p>styrene butadiene</p> <p>Colour: </p> <p>pink – violet</p> <p>Mixing ratio: <br /> </p> <p>undiluted on non-absorbent substrates, <br />diluted 1:1 with water on absorbent substrates</p> <p>Application/ <br />substrate temp: </p> <p>+5°C to +25 °C</p> <p>Consumption: approx. 50–100 g/m², dependent on the <br />porosity of the substrate <br />Packaging: </p> <p>1. 5 and 5 kg containers</p> <p>TS/CoS/JD</p> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstrasse 2–8 <br />D-32760 Detmold (Germany) <br />phone +49-5231-953-00 <br />fax <br />+49-5231-953-108 <br />email export@schomburg.de <br />www.schomburg.com</p> <p>49/15</p> <p>Areas of application: <br />• ASO®-Unigrund-S is used as a primer to improve the adhesion <br />to absorbent and non-absorbent substrates prior to the <br />installation of ceramic finishes with cementbased or dispersionbased SCHOMBURG thin or midbed adhesives. <br />• ASO®-Unigrund-S is also suitable for priming clean, old, <br />load-bearing tiled finishes, which have been levelled up to <br />a maximum thickness of 20 mm with SOLOPLAN®-30 or <br />ASO®-NM15. <br />• ASO®-Unigrund-S reduces the porosity of the substrate and <br />protects moisture sensitive substrates from the water in cementbased adhesives. <br />• ASO®-Unigrund-S is suitable as an adhesion promoter for <br />surface applied waterproof membranes (e.g. SANIFLEX, <br />AQUAFIN®-2K/M), thin-bed adhesives as well as wall and <br />floor levelling compounds such as SOLOCRET®-50, <br />SOLOPLAN®-30 and ASO®-NM15. It is also suitable for <br />exterior use.</p> <p>Subject to changes. Consult current technical data sheet for most recent information.</p> <p>* at +20 °C and 65 % relative humidity</p> <p>2 04201</p> <p>ASO®-Unigrund-S <br />Rapid special adhesion <br />promoting primer</p> <p>v er</p> <p>y lo</p> <p>1 Cleaning the substrate</p> <p>2 ASO®-Unigrund-S and suitable tools</p> <p>3 Pouring out ASO®-Unigrund-S</p> <p>4 Evenly spreading ASO®-Unigrund-S with a <br />lamb’s wool roller</p> <p>5 Dried ASO®-Unigrund-S</p> <p>6 Combing out e.g. a thin-bed adhesive</p> <p>7 Cleaning an absorbent substrate</p> <p>8 Diluting ASO®-Unigrund-S 1:1 with water</p> <p>9 Priming the substrate with undiluted <br />ASO®-Unigrund-S</p> <p>10 Combing out e.g. a thin-bed adhesive</p> <p>Application: <br />The substrate must be load-bearing, clean, dry and free from materials, <br />which will impede adhesion. Flow screeds must be abraded and <br />vacuumed. Remove unstable or weakly bonded layers e.g. release agents, <br />residues of old adhesive, levelling layers, surface finishes and paints, by <br />mechanical scrubbing, planing, scabbling or shot-blasting.</p> <p>io n</p> <p>Properties: <br />• High adhesion strength to <br />non-absorbent substrates <br />• High grip primer once dried due <br />to the silicate based aggregates <br />• Rapid drying <br />• Universal application <br />• For absorbent and nonabsorbent substrates <br />• Low emissions <br />• Solvent free <br />• For interior and exterior use</p> <p>Product preparation: <br />Shake thoroughly before use. Evenly apply a thin coat of ASO®-Unigrund-S <br />at right angles with a foam or lamb’s wool roller. Use neat on non-absorbent <br />substrates, on absorbent substrates dilute 1:1 with water. On nonporous <br />substrates further processes may only be carried out once completely dry. <br />Drying time approx. 1 hour. On absorbent substrates tiles can be laid as <br />soon as the ASO®-Unigrund-S is surface dry – approx. 5 minutes – and <br />touch-dry. The dry coating is transparent-pink and sand grey. <br />When using externally, protect ASO®-Unigrund-S with a bonded <br />waterproofing system for use beneath tiled finishes e.g. AQUAFIN®-2K/M <br />or AQUAFIN®-RS300.</p> <p>w e m is</p> <p>s</p> <p>Information about the emission level of volatile compounds in indoor <br />air, which pose a health risk by inhalation, on a scale from class A+ <br />(very low emissions) to C (high emissions).</p>
