AQUAFIN-CJ6.pdf
7 Seiten
900 KB
Herunterladen
<h1>AQUAFIN-CJ6.pdf</h1> <p>SCHOMBURG GmbH & Co. KG <br />Aquafinstr. 2-8 <br />Detmold <br />NRW <br />32760, Germany</p> <p>Tel: +49 5231 953 00 Fax: +49 5231 953 333</p> <p>Agrément Certificate <br />20/5741</p> <p>e-mail: info@schomburg.de <br />website: www.schomburg.com</p> <p>Product Sheet 3</p> <p>SCHOMBURG WATERPROOF CONCRETE CONSTRUCTION SYSTEM <br />AQUAFIN-CJ6 <br />This Agrément Certificate Product Sheet(1) relates to <br />AQUAFIN-CJ6, a flexible, hydrophilic waterstop for use at <br />construction joints and penetrations in underground <br />reinforced waterproof concrete structures. <br />(1) Hereinafter referred to as ‘Certificate’.</p> <p>CERTIFICATION INCLUDES: <br />• factors relating to compliance with Building Regulations <br />where applicable <br />• factors relating to additional non-regulatory information <br />where applicable <br />• independently verified technical specification <br />• assessment criteria and technical investigations <br />• design considerations <br />• installation guidance <br />• regular surveillance of production <br />• formal three-yearly review. <br />KEY FACTORS ASSESSED <br />Resistance to water pressure — the product provides an effective barrier to the passage of moisture <br />from the ground (see section 6). <br />Durability — when fully enclosed in a concrete structure the product will remain effective as a <br />waterstop for the life of the structure in which it is incorporated (see section 8).</p> <p>The BBA has awarded this Certificate to the company named above for the product described herein. This product <br />has been assessed by the BBA as being fit for its intended use provided it is installed, used and maintained as set <br />out in this Certificate. <br />On behalf of the British Board of Agrément <br />Date of First issue: 15 April 2020</p> <p>Hardy Giesler <br />Chief Executive Officer</p> <p>The BBA is a UKAS accredited certification body – Number 113. <br />The schedule of the current scope of accreditation for product certification is available in pdf format via the UKAS link on the BBA website at www.bbacerts.co.uk <br />Readers MUST check the validity and latest issue number of this Agrément Certificate by either referring to the BBA website or contacting the BBA directly. <br />Any photographs are for illustrative purposes only, do not constitute advice and should not be relied upon.</p> <p>British Board of Agrément <br />Bucknalls Lane <br />Watford <br />Herts WD25 9BA</p> <p>©2020 <br />Page 1 of 7</p> <p>tel: 01923 665300 <br />clientservices@bbacerts.co.uk <br />www.bbacerts.co.uk</p> <p>Regulations <br />In the opinion of the BBA, AQUAFIN-CJ6, if installed, used and maintained in accordance with this Certificate, can <br />satisfy or contribute to satisfying the relevant requirements of the following Building Regulations (the presence of a <br />UK map indicates that the subject is related to the Building Regulations in the region or regions of the UK depicted):</p> <p>The Building Regulations 2010 (England and Wales) (as amended) <br />Requirement: <br />Comment:</p> <p>C2(a)</p> <p>Resistance to moisture <br />The product can contribute to satisfying this Requirement. See section 6 of this <br />Certificate.</p> <p>Regulation: <br />Comment:</p> <p>7(1)</p> <p>Materials and workmanship <br />The product is acceptable. See section 8.1 and the Installation part of this Certificate.</p> <p>The Building (Scotland) Regulations 2004 (as amended) <br />Regulation: <br />Comment:</p> <p>8(1)</p> <p>Durability, workmanship and fitness of materials <br />The product is acceptable. See section 8.1 and the Installation part of this Certificate.</p> <p>Regulation: <br />Standard: <br />Comment:</p> <p>9 <br />3.4</p> <p>Building standards applicable to construction <br />Moisture from the ground <br />The product can contribute to satisfying this Standard, with reference to clauses <br />3.4.1(1)(2), 3.4.5(1)(2) and 3.4.7(1)(2) of this Standard. See section 6 of this Certificate.</p> <p>Standard: <br />Comment:</p> <p>7.1(a)</p> <p>Statement of sustainability <br />The product can contribute to meeting the relevant requirements of Regulation 9, <br />Standards 1 to 6 and therefore will contribute to a construction meeting a bronze level <br />of sustainability as defined in this Standard.</p> <p>Regulation: <br />Comment:</p> <p>12</p> <p>Building standards applicable to conversions <br />All comments given for the product under Regulation 9, Standards 1 to 6 also apply to <br />this Regulation, with reference to clause 0.12.1(1)(2) and Schedule 6(1)(2). <br />(1) Technical Handbook (Domestic). <br />(2) Technical Handbook (Non-Domestic).</p> <p>The Building Regulations (Northern Ireland) 2012 (as amended) <br />Regulation: <br />Comment:</p> <p>23(a)(i) <br />(iv)(b)(i)</p> <p>Fitness of materials and workmanship <br />The product is acceptable. See section 8.1 and the Installation part of this Certificate.</p> <p>Regulation: <br />Comment:</p> <p>28(a)</p> <p>Resistance to moisture and weather <br />The product is an effective barrier to water under hydrostatic pressure. See section 6 of <br />this Certificate.</p> <p>Construction (Design and Management) Regulations 2015 <br />Construction (Design and Management) Regulations (Northern Ireland) 2016 <br />Information in this Certificate may assist the client, designer (including Principal Designer) and contractor (including <br />Principal Contractor) to address their obligations under these Regulations. <br />See section:</p> <p>3 Delivery and site handling (3.1 and 3.3) of this Certificate.</p> <p>Page 2 of 7</p> <p>Additional Information <br />NHBC Standards 2020 <br />In the opinion of the BBA, AQUAFIN-CJ6, if installed, used and maintained in accordance with this Certificate, can satisfy <br />or contribute to satisfying the relevant requirements in relation to NHBC Standards, Chapter 5.4 Waterproofing of <br />basements and other below ground structures (requiring proprietary waterproofing materials to comply with Technical <br />Requirement R3). <br />Unless it can be demonstrated that the water table is permanently below the underside of the slab, the product must <br />be used within a Type B(1) waterproofing protection product, in combination with either a Type A (1) or C(1) waterproofing <br />protection where Grade 3(1) protection is required and the below ground wall retains more than 600 mm (measured <br />from the top of the retained ground to the lowest finished floor level). <br />(1) As defined in BS 8102 : 2009.</p> <p>Technical Specification <br />1 Description <br />1.1 AQUAFIN-CJ6 is a flexible hydrophilic waterstop. It is red in colour and measures 20 mm wide by 5 mm in thickness. <br />1.2 An ancillary item that is available for use with the product, and which is included in this Certificate is: <br />• AQUAFIN-CA – used to secure AQUAFIN-CJ6 to the concrete substrate.</p> <p>2 Manufacture <br />2.1 The compound is manufactured by a batch blending process and then extruded into strips and cut to length. <br />2.2 As part of the assessment and ongoing surveillance of product quality, the BBA has: <br />• <br />• <br />• <br />• <br />• <br />•</p> <p>agreed with the manufacturer the quality control procedures and product testing to be undertaken <br />assessed and agreed the quality control operated over batches of incoming materials <br />monitored the production process and verified that it is in accordance with the documented process <br />evaluated the process for management of nonconformities <br />checked that equipment has been properly tested and calibrated <br />undertaken to carry out the above measures on a regular basis through a surveillance process, to verify that the <br />specifications and quality control operated by the manufacturer are being maintained.</p> <p>2.3 The management systems of Schomburg GmbH & Co. KG have been assessed and registered as meeting the <br />requirements of BS EN ISO 9001 : 2015 by TÜV Rheinland Cert GmbH International (Certificate 01 100 6383/05).</p> <p>3 Delivery and site handling <br />3.1 AQUAFIN-CJ6 is supplied in 40 m rolls, which are packaged in a carton containing 5 rolls and having a gross weight <br />of approximately 25 kg. Cartons can be supplied on pallets containing a maximum of 20 cartons. <br />3.2 The product must be stored under cover, clear of the ground and protected from UV, moisture, frost and other <br />sources of contamination at a temperature of between 5 and 35°C. When stored correctly in unopened packs, <br />AQUAFIN-CJ6 will have a shelf life of at least two years from the date of manufacture. <br />3.3 The Certificate holder has taken the responsibility of classifying and labelling the product under the CLP Regulation <br />(EC) No 1272/2008 on the classification, labelling and packaging of substances and mixtures. Users must refer to the <br />relevant Safety Data Sheet(s).</p> <p>Page 3 of 7</p> <p>Assessment and Technical Investigations <br />The following is a summary of the assessment and technical investigations carried out on AQUAFIN-CJ6.</p> <p>Design Considerations <br />4 Use <br />4.1 The product is satisfactory for use as part of a Type B (structurally integral) protection (as defined in BS 8102 : <br />2009) to waterproof construction joints and penetrations in underground waterproof reinforced concrete structures. <br />4.2 The product is not suitable for use in movement joints, eg expansion joints. <br />4.3 The product swells on contact with water and must be fully confined within the concrete structure to form an <br />effective seal. <br />4.4 The unconfined AQUAFIN-CJ6 will expand by up to 550 % by volume in neutral pH water. The expansion under <br />alkaline or acidic water conditions will be less, but will be adequate to enable the product to form an effective seal <br />when fully confined. <br />4.5 The product will shrink on drying, but will re-hydrate on wetting and re-swell to provide an effective seal. <br />4.6 The ability of the product to expand and form an effective seal can be adversely affected by the groundwater <br />chemistry, especially saline conditions. A detailed study of this aspect must be carried out to establish the presence of <br />any contamination. The Certificate holder must be consulted for advice on specific applications, service conditions and <br />groundwater chemistry. <br />4.7 The product will develop significant pressure when confined within a concrete structure and must be covered by at <br />least 80 mm of concrete from each edge to avoid damage to the concrete.</p> <p>5 Practicability of installation <br />5.1 The product must only be installed by contractors who have been trained by the Certificate holder. <br />5.2 To avoid premature swelling, the product must be protected from contact with water until enclosed in the <br />structure and must not be placed during rain or when rain is forecast.</p> <p>6 Resistance to water pressure <br />6.1 When confined, the product forms an effective barrier to water under hydrostatic pressure from the <br />ground in water-resistant reinforced concrete construction joints. <br />6.2 The product was tested at a maximum hydrostatic water pressure of 4.0 bar and remained watertight. <br />6.3 An appropriate safety factor must be applied to the maximum water pressure given in section 6.2 and the use of <br />additional waterproof protection should be considered, depending on the specific use and risks associated with any <br />particular structure.</p> <p>7 Maintenance <br />As the product is confined within the structure and has suitable in-situ durability, maintenance is neither possible nor <br />required.</p> <p>Page 4 of 7</p> <p>8 Durability <br />8.1 AQUAFIN-CJ6 will function effectively as a waterstop and provide an effective barrier to water under <br />hydrostatic pressure for the life of the structure in which it is incorporated.</p> <p>8.2 The durability of the product may be affected if dislodged or damaged during or following installation, therefore <br />care must be taken to ensure that the product remains in position and is not dislodged when concrete is poured over it, <br />nor damaged during subsequent actions, eg vibration.</p> <p>Installation <br />9 General <br />9.1 AQUAFIN-CJ6 must be placed onto smooth and dust-free concrete surfaces. Uneven and irregular surfaces must be <br />levelled using a suitable mastic. The Certificate holder must be consulted for suitable products, the performance of <br />which are outside of the scope of this Certificate. <br />9.2 Dust, dirt and other debris must be removed using a stiff brush and/or suitable mechanical means.</p> <p>10 Procedure <br />Placing <br />10.1 AQUAFIN-CJ6 is unrolled and placed onto the concrete surface to sit centrally between the inner and outer rows <br />of the reinforcing bars. <br />10.2 A minimum of 80 mm concrete coverage must be ensured around all edges. <br />10.3 Roll ends must be placed to have an overlap of ≥50 mm and pressed firmly together, or by butt jointing. Butt <br />joints must be covered by a separate section of waterstop with a 30 mm overlap to both sections. <br />Fixing <br />10.4 AQUAFIN-CA can be used on clean substrates, wire brushed to remove all contamination. A 10 mm bead of <br />AQUAFIN-CA is gunned onto the substrate, and the product firmly pressed into the adhesive. <br />Enclosing <br />10.5 Prior to enclosing AQUAFIN-CJ6, the placed product must be inspected for damage and premature swelling. If <br />damaged and/or swollen, the product must be replaced at this stage. <br />10.6 Concrete is then poured to enclose the product, compacting well around the waterstop but taking particular care <br />not to dislodge or damage the strip during the process.</p> <p>Technical Investigations <br />11 Tests <br />Tests were carried out on samples of AQUAFIN-CJ6 and the results assessed to determine: <br />• <br />• <br />• <br />• <br />•</p> <p>product characteristics <br />resistance to hydrostatic water pressure <br />unrestricted swelling characteristics under alkali, neutral and acidic water conditions <br />effect of wet/dry cycles on swelling characteristics <br />load developed when restrained. <br />Page 5 of 7</p> <p>12 Investigations <br />The manufacturing process was evaluated, including the methods adopted for quality control, and details were <br />obtained of the quality and composition of the materials used.</p> <p>Bibliography <br />BS 8102 : 2009 Code of practice for protection of below ground structures against water from the ground <br />EN ISO 9001 : 2015 Quality management systems — Requirements</p> <p>Page 6 of 7</p> <p>Conditions of Certification <br />13 Conditions <br />13.1 This Certificate: <br />• relates only to the product/system that is named and described on the front page <br />• is issued only to the company, firm, organisation or person named on the front page – no other company, firm, <br />organisation or person may hold or claim that this Certificate has been issued to them <br />• is valid only within the UK <br />• has to be read, considered and used as a whole document – it may be misleading and will be incomplete to be <br />selective <br />• is copyright of the BBA <br />• is subject to English Law. <br />13.2 Publications, documents, specifications, legislation, regulations, standards and the like referenced in this <br />Certificate are those that were current and/or deemed relevant by the BBA at the date of issue or reissue of this <br />Certificate. <br />13.3 This Certificate will remain valid for an unlimited period provided that the product/system and its manufacture <br />and/or fabrication, including all related and relevant parts and processes thereof: <br />• are maintained at or above the levels which have been assessed and found to be satisfactory by the BBA <br />• continue to be checked as and when deemed appropriate by the BBA under arrangements that it will determine <br />• are reviewed by the BBA as and when it considers appropriate. <br />13.4 The BBA has used due skill, care and diligence in preparing this Certificate, but no warranty is provided. <br />13.5 In issuing this Certificate the BBA is not responsible and is excluded from any liability to any company, firm, <br />organisation or person, for any matters arising directly or indirectly from: <br />• the presence or absence of any patent, intellectual property or similar rights subsisting in the product/system or any <br />other product/system <br />• the right of the Certificate holder to manufacture, supply, install, maintain or market the product/system <br />• actual installations of the product/system, including their nature, design, methods, performance, workmanship and <br />maintenance <br />• any works and constructions in which the product/system is installed, including their nature, design, methods, <br />performance, workmanship and maintenance <br />• any loss or damage, including personal injury, howsoever caused by the product/system, including its manufacture, <br />supply, installation, use, maintenance and removal <br />• any claims by the manufacturer relating to CE marking. <br />13.6 Any information relating to the manufacture, supply, installation, use, maintenance and removal of this <br />product/system which is contained or referred to in this Certificate is the minimum required to be met when the <br />product/system is manufactured, supplied, installed, used, maintained and removed. It does not purport in any way to <br />restate the requirements of the Health and Safety at Work etc. Act 1974, or of any other statutory, common law or <br />other duty which may exist at the date of issue or reissue of this Certificate; nor is conformity with such information to <br />be taken as satisfying the requirements of the 1974 Act or of any statutory, common law or other duty of care.</p> <p>British Board of Agrément <br />Bucknalls Lane <br />Watford <br />Herts WD25 9BA</p> <p>©2020</p> <p>Page 7 of 7</p> <p>tel: 01923 665300 <br />clientservices@bbacerts.co.uk <br />www.bbacerts.co.uk</p>
